• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.6
• /
• pp.495-500
• /
• 2017

In the boundary layer of supersonic or hypersonic vehicles, there is the conversion from kinetic energy to thermal energy, called aerodynamic heating. Aerodynamic heating has to be considered to design supersonic vehicles, because it induces severe heat flux to surface. Transient heat transfer analysis with CFD is used to predict thermal response of vehicles, however transient heat transfer analysis needs excessive computing powers. Loosely coupled method is widely used for evaluating thermal response, however it needs to be revised for overestimated heat flux. In this research, quasi-transient method, which is combined loosely coupled method and conjugate heat transfer analysis, is proposed for evaluating thermal response with efficiency and reliability. Defining reference time of splitting flight scenario for transient simulation is important on accuracy of quasi-transient method, however there is no algorithm to determine. Therefore the research suggests the algorithm with various flow conditions to define reference time. Supersonic flow field of blunt body with constant acceleration is calculated to evaluate quasi-transient method. Temperature difference between transient and quasi-transient method is about 11.4%, and calculation time reduces 28 times for using quasi-transient method.

• Solar Energy
• /
• v.17 no.4
• /
• pp.3-11
• /
• 1997

Because grain boundaries in polycrystalline silicon act as potential barriers and recombination centers for the photo-generated charge carriers, these defects degrade conversion effiency of solar cell. To reduce these effects of grain boundaries, we investigated various influencing factors such as thermal treatment, various grid pattern, selective wet etching for grain boundaries, buried contact metallization along grain boundaries, grid on metallic thin film. Pretreatment above $900^{\circ}C$ in $N_2$ atmosphere, gettering by $POCl_3$ and Al treatment for back surface field contributed to obtain a high quality poly-Si. To prevent carrier losses at the grain boundaries, we carried out surface treatment using Schimmel etchant. This etchant delineated grain boundaries of $10{\mu}m$ depth as well as surface texturing effect. A metal AI diffusion into grain boundaries on rear side reduced back surface recombination effects at grain boundaries. A combination of fine grid with finger spacing of 0.4mm and buried electrode along grain boundaries improved short circuit current density of solar cell. A ultra-thin Chromium layer of 20nm with transmittance of 80% reduced series resistance. This paper focused on the grain boundary effect for terrestrial applications of solar cells with low cost, large area, and high efficiency.

• Journal of Radiation Protection and Research
• /
• v.33 no.2
• /
• pp.67-76
• /
• 2008

As the first comprehensive attempt at a national implementation, this study aims at assessing the external costs of major electricity generation technologies in Korea, particularly an evaluation of the impacts on human health resulting from exposures to atmospheric radiological emissions from nuclear power plants, and a monetary quantification of their damages. The methodology used for the assessment of the externalities of the selected fuel cycles has been developed by the International Atomic Energy Agency (IAEA), namely the SimPacts Model Package. The model is internationally recognized as a tool which can be applied to a wide range of fuels, different technologies and locations, for an externalities study. In this study, the relevant emissions are quantified first and then their impacts on human health are evaluated and compared. The study focused on all the nuclear power plants for the last 6 years ($2001{\sim}2006$) in Korea. With respect to nuclear power, the impact analysis only focuses on a power generation, however the front- and back-end nuclear fuel cycles are not included, namely uranium mining, conversion, enrichment, reprocessing, conditioning, etc., because these facilities are not present in Korea. The analysis results show that nuclear power in general, generates low external costs. The highest damage costs from the nuclear power plants among the 4 sites in Korea were estimated to be 3.9 mills/MWh, which is about 1/20th of the result for a similar case study conducted in the U.K., implemented through the ExternE project. This difference is largely due to the number of radionuclides included in the study and the amount of released radioactive emissions based on up-to-date information in Korea. In this study, the sensitivities of the major factors for nuclear power plants were also calculated. The analysis indicates that there was around a ${\pm}3%$ damage costs variation to a ${\pm}15%$ change of the reference population density and a ${\pm}1%$ damage cost variation to a $1{\sim}30$ meters change of the effective release height, respectively. These sensitive calculations show that there is only a minor difference when the reference costs are compared.

• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.219-224
• /
• 2012

We study for long-term performance of amorphous silicon solar cells under light exposure. The performance is predicted with a kinetic model in which the carrier lifetimes are determined by the defect density. In particular, the kinetic model is described by the stretched-exponential relaxation of defects to reach equilibrium. In this report, we simulate the light-induced degradation of the amorphous silicon solar cells with the kinetic model and AMPS-1D computer program. And data measured for outdoor performances of various solar cells are compared with the simulated results. This study focuses on examining the light-induced degradation for the following amorphous silicon pin solar cells: thickness${\approx}$300 nm, built-in potential${\approx}$1.05 V, defect density (at t=0)${\approx}5{\times}10^{15}cm^{-3}$, short-circuit current density (at t=0)${\approx}15.8mA/cm^2$, fill factor (at t=0)${\approx}0.691$, open-circuit voltage (at t=0)${\approx}0.865V$, conversion efficiency (at t=0)${\approx}9.50%$.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.4
• /
• pp.232-236
• /
• 1999

A solar cell based on dye-sensitized photoelectric conversion was studied by electrochemical and spec-trofluorometric methods for the purposes of enhancing its efficiency and stability of $TiO_2$ solar cells. Nanocrystalline $TiO_2$ was used to prepare photoelectrodes, and photosensitizing dyes such as malachite green oxalate, basic blue3, rhodamine B, and bromocresol purple were chosen as sensitizers. Electrochemical oxidation potentials and absorption and emission wavelengths of dyes were used to determine energy levels of the dyes. By comparing excited energy levels of the dyes with the conduction band edge potential $(E_{c,s})\;of\;TiO_2$ calculated by using the flat-band potential $(E_{fb})\;of\;TiO_2$, properties of a dye required to fabricate a high efficient photosensitizing solar cell with high short-circuit current $(J_{sc})$ were suggested. Enhanced stability of photocurrent was obtained by coating a $TiO_2|ITO$ electrode with Polypyrrole that Possibly Prevented the recombination between the conduction band electrons and oxidized dyes and suppressed the direct electrode redox reactions of dyes on ITO.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.5
• /
• pp.326-332
• /
• 2012

In this paper, error analyses on the calculation of offshore wind speed have been conducted using HeMOSU-1 data to develop offshore wind energy in Yeonggwang sea of Korea and onshore observed wind data in Buan, Gochang and Yeonggwang for 2011. Offshore wind speed data at 98.69 m height above M.S.L is estimated using relational expression induced by linear regression analysis between onshore and offshore wind data. In addition, estimated offshore wind speed data is set at 87.65 m above M.S.L using power law wind profile model with power law exponent(0.115) and its results are compared with the observed data. As a result, the spatial adjustment error are 1.6~2.2 m/s and the altitude adjustment error is approximately 0.1 m/s. This study shows that the altitude adjustment error is about 5% of the spatial adjustment error. Thus, long term observed data are needed when offshore wind speed was estimated by onshore wind speed data. because the conversion of onshore wind data lead to large error.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.940-947
• /
• 2006

A variety of actuators fur an implantable artificial heart have been studied. They, all, however, share the disadvantages of a complicated energy conversion mechanism and of the need to use bearings. A ferrofluidic actuator directly drives magnetic fluids by applying a magnetic field to these fluids; it does not require bearings. In this study, the feasibility of a ferrofluidic actuator for an implantable artificial heart was studied. An way of two Poles of ring solenoids was mounted near the acrylic tube $({\phi}\;7.4mm)$. A rubber sack (volume : $2m{\ell}$ was connected to both ends of the acrylic tube. The sack were encased in a rigid chamber that had inlet and outlet ports. The acrylic tube and the rubber sack were filled with water encased in a rigid chamber magnetic fluid and the iron cylinder were immersed in the water. Two experiment method was conducted. 1) distance between stoppers were 72mm and 2) distance between stoppers were 104mm. A stroke volume was stability and $0.96m{\ell}$ was obtained in the experiment 1 and $1.92m{\ell}$ in the experiment 2. The energy efficiency of Experiment method 2 is about five times than Experiment method 2. A magnetic fluid-driven blood pump could be feasible if the magnetic fluid with high magnetization (3 times yester than the current value) is developed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.201-208
• /
• 2017

Recently, the installation of photovoltaic(PV) systems has been increasing due to the worldwide interest in eco-friendly and abundant solar energy. On the other hand, a PV system has approximately 25% power loss while the energy generated from solar cells is transformed to the power coupling point through a power conversion system (DC/AC). If the output voltage of a string in the PV system is lower than the operating range of the inverter when a part of module in the string has a shadow due to weather conditions, the string is not synchronized and the whole efficiency of output power in a PV system may be reduced significantly. Therefore, to overcome this problem, this paper proposes a novel control method to compensate for the lower voltage by introducing a DC/DC voltage regulator for each string in a PV system, which adopts a concept for MPPT (Maximum Power Point Tracking) control function using the P&O algorithm and adopts constant voltage control method used in an existing inverter. This paper also implements a 2kW DC/DC voltage regulator based on the proposed algorithm and performs a variety of scenario-based experiments. From the simulation result, it was confirmed that the operation efficiency in the proposed method is improved compared to the existing method.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.647-655
• /
• 2021

The IMO (International Maritime Organization) is discussing the improvement of energy ef iciency of ships in order to reduce greenhouse gas emissions from ships. Currently, by applying an ORC power generation system using waste heat generated from ships, high energy conversion efficiency can be expected from ships. This technology uses an organic medium based on Freon or hydrocarbons as the working fluid, which evaporates at a lower temperature range than water. Through this, it is possible to generate steam (gas) and generate power at a low and low temperature relatively. In this study, the analysis of heat flow between the refrigerant and waste heat in the ORC power generation system, which is an organic Rankine cycle, is analyzed using 3D simulation techniques to determine the temperature change, velocity change, pressure change, and mass change of the fluid flowing of the WHRU (Waste Heat Recovery Unit) inside and the outside the structure. The purpose of this study is to analyze how the mass change affects the structure, and this study analyzed the heat transfer of the heat exchanger from the refrigerant and the exhaust gas of the ship's main engine in the ORC power generation system using this technique.

• Clean Technology
• /
• v.24 no.4
• /
• pp.307-314
• /
• 2018

In this study, NMO (Natural Manganese Ore), $MnO_2$, and $Mn_2O_3$ catalysts were used in the selective catalytic reduction process to remove nitrogen oxides (NOx) using $NH_3$ as a reducing agent at low temperatures in the presence of oxygen. In the case of the NMO (Natural Manganese Ore), it was confirmed that the conversion of nitrogen oxides in the stability test did not change even after 100 hours at 423 K. The Kinetics experiments were carried out within the range where heat and mass transfer were not factors. From a steady-state Kinetics study, it was found that the low-temperature SCR reaction was zero order with the respect to $NH_3$ and 0.41 ~ 0.57 order with the respect to NO and 0.13 ~ 0.26 order with the respect to $O_2$. As temperature increases, the reaction order decreases as a result of $NH_3$ and oxygen concentration. It was confirmed that the reaction between the $NH_3$ dissociated and adsorbedon the catalyst surface and the gaseous nitrogen monoxide (E-R model) and the reaction with the adsorbed nitrogen monoxide (L-H model) occur.