• Journal of Korea Multimedia Society
• /
• v.10 no.1
• /
• pp.49-57
• /
• 2007

Recently, CMOS RF integration has been widely explored in the wireless communication area to save cost, power, and chip area. The direct conversion architecture, rather than a more conventional super-het-erodyne, has been an attractive choice for single-chip integration because of its many advantages. However, the direct conversion architecture has several fundamental problems to solve in achieving performance comparable to a super-heterodyne counterpart. In this paper, we describe a programmable filter for mobile communication terminals using a direct conversion architecture. The proposed filter can be implemented with the active-RC filter and programmed to meet the requirements of different communication standards, including GSM, DECT and WCDMA. The filter can be tuned to select a detail frequency by changing the gate voltage of the MOS resistors. The gain of the proposed architecture can be programmed from 27dB to 72dB using the filter gain and VGA in 3dB steps.

• Journal of Korea Multimedia Society
• /
• v.17 no.7
• /
• pp.797-805
• /
• 2014

In this paper we propose a new frame rate up conversion scheme which is used to overcome the motion blur problem of liquid crystal display caused by its slow response. The conventional bilateral motion estimation method which is mainly used in the frame rate up conversion scheme has a drawback that it cannot find true motion vector if there are blocks with simple texture in the search range. To solve this problem, a texture adaptive bilateral motion estimation method that increases cost value of block with simple texture is proposed. Also a motion estimation scheme that utilizes neighboring motion vector effectively is proposed to reduce computation time required to estimate motion. Since the proposed scheme does not apply all available motion vectors within the search range, the execution time of frame rate up conversion can be reduced dramatically. Experimental results show that the interpolated frame image quality of the proposed method is improved in subjective as well as objective view point compared with that of the conventional method.

• Nuclear Engineering and Technology
• /
• v.54 no.4
• /
• pp.1482-1494
• /
• 2022

Power conversion cycles (Subcritical Steam, Supercritical Steam, Open Air Brayton, Recuperated Air Brayton, Combined Cycle, Closed Brayton Supercritical CO₂ (sCO₂), and Stirling) are evaluated for land-based nuclear microreactors based on technical maturity, system efficiency, size, cost and maintainability, safety implications, and siting considerations. Based upon these criteria, Air Brayton systems were selected for further evaluation. A brief history of the development and applications of Brayton power systems is given, followed by a description of how these thermal-to-electrical energy conversion systems might be integrated with a nuclear microreactor. Modeling is performed for optimized cycles operating at 3 MW(e) with turbine inlet temperatures of 500 ℃, 650 ℃ and 850 ℃, corresponding to: a) sodium fast, b) molten salt or heat pipe, and c) helium or sodium thermal reactors, coupled with three types of Brayton power conversion units (PCUs): 1) simple open-cycle gas turbine, 2) recuperated open-cycle gas turbine, and 3) recuperated and intercooled open-cycle gas turbine. Aeroderivative turboshaft engines employing the simple Brayton cycle and two industrial gas turbine engines employing recuperated air Brayton cycles are also analyzed. These engines offer mature technology that can facilitate near-term deployment with a modest improvement in efficiency.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.718-724
• /
• 2018

With the development of photovoltaic industry, the cost of photovoltaic power generation has become the significant issue. And the metallization process has decided the cost of original materials and photovoltaic efficiency of the solar cells. Nowadays, double printing process has been introduced instead of one-step printing process for front contact of polycrystalline silicon solar cells, which can effectively improve the photovoltaic conversion efficiency of silicon solar cells. Here, the relative cheap Cu paste has replaced the expensive Ag paste to form Ag/Cu composite front contact of silicon solar cells. The photovoltaic performance and the cost of photovoltaic power generation have been investigated. With the optimization on structure and height of Cu finger layer for Ag/Cu composite double-printed front contact, the silicon solar cells have exhibited a photovoltaic conversion efficiency of 18.41%, which has reduced 3.42 cent per Watt for the cost of photovoltaic power generation.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.18 no.8
• /
• pp.2450-2463
• /
• 2024

Many legacy information systems are currently being clouded. This is due to the advantage of being able to respond flexibly to the changes in user needs and system environment while reducing the initial investment cost of IT infrastructure such as servers and storage. The infrastructure of the information system migrated to the cloud is being integrated through the API connections, while being subdivided by using MSA (Micro Service Architecture) internally. DBMS (Database Management System) is also becoming larger after cloud migration. Scale calculation in most layers of the application architecture can be measured and calculated from auto-scaling perspective, but the method of hardware scale calculation for DBMS has not been established as standardized methodology. If there is an error in hardware scale calculation of DBMS, problems such as poor performance of the information system or excessive auto-scaling may occur. In addition, evaluating hardware size is more crucial because it also affects the financial cost of the migration. CPU is the factor that has the greatest influence on hardware scale calculation of DBMS. Therefore, this paper aims to calculate the conversion factor for CPU scale calculation that will facilitate the cloud migration between heterogeneous DBMS. In order to do that, we utilize the concept and definition of hardware capacity planning and scale calculation in the on-premise information system. The methods to calculate the conversion factor using TPC-H tests are proposed and verified. In the future, further research and testing should be conducted on the size of the segmented CPU and more heterogeneous DBMS to demonstrate the effectiveness of the proposed test model.

• Current Photovoltaic Research
• /
• v.8 no.3
• /
• pp.94-101
• /
• 2020

This study was trying to focus on achieving high efficiency of multi junction solar cell with thin film silicon solar cells. The proposed thin film Si-Ge/c-Si tandem junction solar cell concept with a combination of low-cost thin-film silicon solar cell technology and high-efficiency c-Si cells in a monolithically stacked configuration. The tandem junction solar cells using amorphous silicon germanium (a-SiGe:H) as an absorption layer of upper sub-cell were simulated through ASA (Advanced Semiconductor Analysis) simulator for acquiring the optimum structure. Graded Ge composition - effect of E_g profiling and inserted buffer layer between absorption layer and doped layer showed the improved current density (J_sc) and conversion efficiency (η). 13.11% conversion efficiency of the tandem junction solar cell was observed, which is a result of showing the possibility of thin film Si-Ge/c-Si tandem junction solar cell.

• Journal of Life Science
• /
• v.11 no.3
• /
• pp.230-234
• /
• 2001

The cyclodextrin glucanotransferase(CGTase) gene of Bacillus macerans was expressed in Saccharomyces cerevisiae and the recombinant CGTase was partially purified from the yeast culture supernatant. The optimal pH and temperature of the CGTase were found to be 6.0 and 5$0^{\circ}C$, respectively. The pH and temperature stabilities of the recombinant enzyme were significantly enhanced and the half life at 55$^{\circ}C$ was about 60 hr. When the recombinant CGTase was reacted with 5% soluble starch, the conversion yield of total cyclodextrin (CD) from starch was estimated to be 41% at 48 hr, whereas the wild type enzyme showed the yield of 12%. This improvement of conversion yield and thermal stability of CGTase may be useful for the development of low-cost CD production process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.85-88
• /
• 2005

A low-cost and high-speed PDP color inspection system can be constructed by using a CCD camera against a colorimeter. Though the inspection can be done using RGB signals obtained by a camera, it has some difficulty to introduce human color sensitivity. Thus, it is quite desirable to convert the RGB values into the XYZ values that can be compared to the values of a colorimeter. Accordingly, the current study proposes a color conversion method that can analytically calculate the RGB-to-XYZ conversion matrix by utilizing the RGB primaries and the reference white. Experiments on Macbeth colorchecker colors showed that the average color difference between the converted XYZ values of the proposed method and the measured XYZ values of a colorimeter is much below the threshold of distinguishing two adjacent color patches.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3230-3232
• /
• 1999

In this paper describes the design and improvement of a hybrid module for dual slope A/D converter. Since the input voltage to be converted is very sensitive and small. A/D converter must have the temperature stability. low-drift, and the high-resolution the conversion. A dual slop A/D converter circuit which is controlled by microprocessoer has been developed to reduce the offset voltage and the drift characteristics of operation amplifiers, and to improve the A/D conversion speed. Also hybrid module has been adapted to obtain the to obtain the stable and accurate A/D conversion for low cost use. The evaluation of the designed hybrid module has been shown as having a good performance, which will give usefull application to the industrial measurements use.

• KSBB Journal
• /
• v.25 no.5
• /
• pp.483-489
• /
• 2010

Biodiesel has attracted great attention as an alternative renewable energy source for the replacement of petroleumbased diesel fuel, yet its high production cost due to expensive oil feedstock remainsas the major economical obstacle. In this study, we investigated catalysts and reaction conditions for the acid catalyzed pre-conversion of free fatty acid (FFA) to fatty acid methyl ester (FAME) in cheap low-grade oils of high acid value. The NaOH base catalyzed reaction of vegetable oil of the initial acid value of 2 mg KOH/g led to a high FAME conversion above 95.4%, but the conversion abruptly decreased at higher initial acid values. This base catalyzed reaction was practically ineffective displaying the FAME conversion below 15% even at the initial acid value of 10 mg KOH/g by the severe saponification side reaction. Among the various catalysts studied for the pre-conversion of FFA to FAME, Amberlyst-15 was the most effective in reducing the acid value, and the optimum reaction condition identified was $65^{\circ}C$ with oil to methanol ratio of 1:3 and catalyst concentration of 15% (w/w). As the results, great enhancements in the overall biodiesel conversion were achievable via a consecutive reaction of the acid catalyzed FFA pre-conversion to FAME under the optimal condition obtained with Amberlyst-15 followed by the NaOH base catalyzed reaction, far above the extent which was obtainable by the single NaOH catalyzed reaction.