• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.168-170
• /
• 1994

Carbide-tipped twist drill of new type which is better than traditional H.S.S twist drill has been developed successfully to drill steel work-pieces with high speed. This new carbide drill consists of a characteristic flature of special shape of cutting edge, chip pocket, and flute. The special design of the chip pocket and the flute guarantees both periodic fracture and smooth transport of chips along the flute. The carbide-tipped twist drill also allows one to apply more drilling force than conventional one and produce holes with high accuracy.

• 대한치과의사협회지
• /
• 제53권5호
• /
• pp.368-376
• /
• 2015

Purpose : The objective of this research was to develop a more simplified drilling procedure with an enhanced implant drill. Materials and Methods : The drill enhanced design factors enabled implantation of Dia. 5.0mm fixture with only 2 times drilling which is more simplified drilling procedure. The enhanced drill was designed with 2 flutes, 2-phase or 3-phase formed drill tip and 25 degrees of helix angle. The proposed drilling procedure (2 times) was compared with a general drilling process (4 times) in terms of temperature changes, cutting time and ISQ value. Results : The simplified drilling procedure indicated less heat than a conventional drilling procedure (p<0.05). The enhanced drill showed significantly shorter drilling time than a conventional drill (p<0.05). On the other hand, higher insertion torque and ISQ value were observed on the the suggested drilling procedure than the conventional drilling procedure (p<0.05). Conclusion : A simplified drilling procedure with the newly designed drill could provide higher effectiveness and safety of dental implant operations under properly controlled external conditions, such as irrigation and RPM of drilling.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 2022년도 추계학술대회
• /
• pp.102-102
• /
• 2022

More than 74% of forage crops in Korea are cultivated in winter rice fields. Italian ryegrass (IRG) can be said to be a representative forage crop, but over 70% of its seeds are dependent on imports. In addition, there are concerns that the stable supply of research fees may be disrupted due to the effects of climate change, war, and other factors. Therefore, it is necessary to secure a large production area for stable supply. Korea's reclaimed land area is 135,000 ha and its agricultural area is 112,000 ha. Therefore, this study attempted to apply IRG to the domestic IRG seed industry through stable cultivation techniques on reclaimed land. In this study, IRG 'Kowiearly' varsity was cultivated in late October 2020 and early October 2021 in the Saemangeum reclaimed land. The seeding methods were conventional drill sowing seeding, new technology spot seedling (30 × 18 cm) and new technology drill sowing seeding. The amount of sowing was conventional drill sowing seeding 2.0(kg/10a), new technology spot seedling 1.5(kg/10a), and new technology drill sowing seeding 1.5(kg/10a). Fertilizer application amount is conventional drill sowing seeding(N-P₂O₅-K₂O) 9.0-12-12(kg/10a), and new technology spot seedling and drill sowing seeding were(N-P₂O₅-K₂O) 4.5-12-12(kg/10a) respectively. Fertilizer was applied accordingly. After that, in February, the conventional drill sowing seeding, new technology drill sowing seeding and spot seedling applied 4.0 and 2.2(kg/10a) of nitrogen supplement fertilizer, respectively. Before wintering, plant length was higher in 2022 than in 2021, but leaf number was higher in 2021. Heading time was April 30, 2021 and April 25, 2022. In heading time, plant length was 74 cm in 2021 and 67 cm in 2022, lower than in 2021. On the other hand, There was no difference in the number of panicle and the number of seeds in the 2021 harvester in all treatment plots, and, thus seed yield was no differ. However, the drill sowing seeding and spot seedling of the new technology were somewhat higher than the conventional drill sowing seeding. On the other hand, seed yield was decreased in all treatment plots compared to 2022 because of raifall deficiency in 2021.

• 한국정밀공학회지
• /
• 제17권3호
• /
• pp.114-121
• /
• 2000

A new concept drill was developed recently (or increasing accuracy and productivity in drilling operation. The burr formation in drilling causes many problems in deburring operation because burrs are formed inside holes and it is difficult to remove them. Burr formations are observed in drilling operation with a new concept drill and are compared with conventional HSS drill. Several workpieces with different materials are drilled with several cutting conditions, velocity and feed rate. The burr in drilling can be classified into three types according to the location of crack. To observe the burr formation mechanism, the cap which is formed with the new concept drill is observed and measured.

• 한국정밀공학회지
• /
• 제17권10호
• /
• pp.132-140
• /
• 2000

In conventional drilling, burr geometry can be changed according to the variation of drill geometry like point angle, rake angle. Step drilling is proposed to minimize the burr formation in drilling operation. The burr formed in first cutting can be removed in second cutting by the edge in step. The burr formed in second cutting by the edge in step can be minimized according to the change of geometry like, step angle and depth. The mechanism in step drilling is analyzed. Some step drills are applied to drilling the input shaft which is used for vehicle steering. To measure the burr formed in drilling, laser and height gage are used.

• 한국기계가공학회지
• /
• 제15권1호
• /
• pp.8-13
• /
• 2016

The micro drill bit automatic regrinding in-line system is a system that refurbishes drill bits used in a PCB manufacturing process. This system is able to refurbish drill bits with a minimum size of ø0.15-0.075mm that have previously been discarded. Beyond the conventional manual cleaning process using ultrasound, this system adopts a water jet cleaning system, making it capable of cleaning drill bits with a minimum size of ø0.15-0.075mm. This paper analyses various contact pressures applied to the surface of drill bits depending on the shooting pressure of the cleaning device and fluid velocity in order to optimize the nozzle location and to detect structural instability caused by the contact pressures.

• 한국작물학회지
• /
• 제41권1호
• /
• pp.28-33
• /
• 1996

벼 건답직파재배에서 화성벼를 공시 종자조건, 파종후 복토 및 파종후 관개시기등을 달리한 파종방법 차이가 입모정도. 생육특성 및 수량에 미치는 영향을 검토하였던 결과는 다음과 같다. 1. 입모수는 파종후 관개배수를 하는 것이 입모후 담수를 하는 것보다 많았으며, 휴입세조파가 평면세조파후 무복토나 점파보다 많았다. 2. 파종후 관개배수가 위묘후 담수보다 출아일수는 6∼10일 짧았고, 출수기는 2∼3일 일렀다. 3. 경수는 생육초기에는 휴입세조파와 평면세조파후 복토(관행 : 건종자로 평면세조파 후 복토를 하고 입모후 담수를 한 파종방법)에서 많았으나, 유수형성기 이후의 경수 및 수수는 평면세조파후 무복토(침종종자로 평면세조파후 복토를 하지 않고 파종직후 관개배수를 한 파종방법)에서 가장 많았다. 4. 도복지수는 휴입세조파가 점파나 평면세조파보다 약간 높았고, 포장도복은 휴입세조파와 평면세조파 무복토에서 1 정도의 가벼운 도복이 발생되었다. 5. 쌀 수량은 관행인 평면세조파후 복토(5.35t/ha)보다 평면세조파후 무복토에서 7％ 증수되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1994년도 가을 학술발표회 논문집
• /
• pp.199-208
• /
• 1994

This paper presents an evaluation of new drill and blast method with two different drilling directions for pilot tunnel enlargement using numerical experiment and field test. To evaluate the effieiency of new tunnel enlargement method, field tests were performed and compared with conventional drill and blast method. Also, three dimensional transient dynamic analysis was made to investigate the effect of the ground vibration when blasting was performed at same position using the equivalent single hole charge.

• 대한산업공학회지
• /
• 제39권3호
• /
• pp.149-155
• /
• 2013

Electric discharging machining (EDM) is commonly adopted to machine the precise and tiny part when it is difficult to meet the productivity and the tolerance by the conventional cutting method. The die-sinking EDM method works well to machine the micro-parts and the perpendicular wall of die and mould, whereas EDM drilling, called super drill, is excellent to machine the deep and narrow hole regardless the material hardness and the hole location. However, the electrode wear is rapid compared to the conventional cutting tool and makes it difficult to control the electrode feeding and to machine precisely. This paper presents an efficient method to estimate the electrode wear using hole pass-through experiment while the stochastic method is used to compensate for the estimation model. To validate the proposed method, the commercial EDM drill machine is used. The experiment result shows that the electrode wear amount can be predicted very precisely.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 추계학술대회 논문집
• /
• pp.298-301
• /
• 1992

A digital image processing approach has been adopted to measure the flank wear area, which is very difficult to measure using conventional techniques. Automatic thresholding of the gray-level values of an image is very useful in automated analysis of image. 1-D entropy thresholding technique is used for image processing and analysis of the flank wear area. This strategy provides more information about drill wear conditions and should therefore have a higher reliability than previous methods. This study calulated quantitatively the flank were area of drill by computer program.