• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.11-18
• /
• 2021

A novel microwave dielectric composite material for ultra-low temperature co-fired ceramics (ULTCC) with (1-x)BaWO₄-xBaV₂O₆ (x=0.54~0.85) composition was prepared by firing a mixture of BaWO₄ and BaV₂O₆. Shrinkage tests showed that the ceramic composite begins to densify at a temperature as low as 550℃ and can be sintered at 650℃ with 98% of relative density under the influence of BaV₂O₆. X-ray diffraction analysis showed that BaWO₄ and BaV₂O₆ coexisted and no secondary phase was detected in the sintered bodies, implying good chemical compatibility between the two phases. Near-zero temperature coefficients of the resonant frequency (𝛕_f) could be achieved by controlling the relative content of the two phases, due to their positive and negative 𝛕_f values, respectively. With increasing BaV₂O₆ (x from 0.53 to 0.85), the 𝛕_f value of the composites increased from -7.54 to 14.49 ppm/℃, ε_r increased from 10.08 to 11.17 and the quality factor (Q×f value) decreased from 47,661 to 37,131 GHz. The best microwave dielectric properties were obtained for x=0.6 samples with ε_r=10.4, Q×f=44,090 GHz, and 𝛕_f=-2.38 ppm/℃. Chemical compatibility experiments showed the developed composites are compatible with aluminum electrode during co-firing process.

• Korean Journal of Ecology and Environment
• /
• v.55 no.2
• /
• pp.99-110
• /
• 2022

We investigated physicochemical properties and isotopic compositions of organic matter (δ¹³C_TOC and δ ¹⁵N_TN) in the old fish farming (OFF) site after the cessation of aquaculture farming. Based on this approach, our objective is to determine the organic matter origin and their relative contributions preserved at sediments of fish farming. Temporal and spatial distribution of particulate and sinking organic matter(OFF sites: 2.0 to 3.3 mg L^-1 for particulate matter concentration, 18.8 to 246.6 g m^-2 day^-1 for sinking organic matter rate, control sites: 2.0 to 3.5 mg L^-1 for particulate matter concentration, 25.5 to 129.4 g m^-2 day^-1 for sinking organic matter rate) between both sites showed significant difference along seasonal precipitations. In contrast to variations of δ¹³C_TOC and δ¹⁵N_TN values at water columns, these isotopic compositions (OFF sites: -21.5‰ to -20.4‰ for δ¹³ C_TOC, 6.0‰ to 7.6‰ for δ¹⁵N_TN, control sites: -21.6‰ to -21.0‰ for δ¹³C_TOC, 6.6‰ to 8.0‰ for δ¹⁵N_TN) investigated at sediments have distinctive isotopic patterns(p<0.05) for seawater-derived nitrogen sources, indicating the increased input of aquaculture-derived sources (e.g., fish fecal). With respect to past fish farming activities, representative sources(e.g., fish fecal and algae) between both sites showed significant difference (p<0.05), confirming predominant contribution (55.9±4.6%) of fish fecal within OFF sites. Thus, our results may determine specific controlling factor for sustainable use of fish farming sites by estimating the discriminative contributions of organic matter between both sites.

• Korea Trade Review
• /
• v.42 no.5
• /
• pp.71-91
• /
• 2017

This purpose of this study is to examine how emotional intelligence has a moderating effect on the relationship between emotional labor and job burnout. To test the hypotheses, moderation analysis, mediation analysis and moderated mediation analysis were performed. Of the 1,500 self-report questionnaires distributed to franchise employees, 1,412 usable responses and utilized in the final analyses. The resoults show that emotional labor significantly affected job burnout, and job burnout completely mediated the effect of emotional labor on turnover intention. And emotional intelligence moderated the relationship between emotional labor and job burnout, suggesting that the emotional dissonance-job burnout relationship was stronger in the low emotional intelligence group than in the high emotional intelligence group. The results of this study provide some implications for Korean companies entering the Chinese franchise field. First, the mediating effects of "emotional labor → job burnout → turnover intention" and the effect of emotional labor on job burnout were mitigated by self-efficacy in Chinese franchise workers. And the self-efficacy of the employees was an important factor. The implication of this study is that self-efficacy, which is a controlling variable affecting emotional labor, job burnout, and turnover intention, is important, so Korean companies that enter the Chinese franchise employ employees with high self-efficacy and to develop and implement an employee education program that can enhance self-efficacy.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.14 no.1
• /
• pp.1-9
• /
• 2009

Export fluxes of particulate organic carbon were estimated for the first time by using $^{234}Th/^{238}U$ disequilibrium in the southwestern East Sea during August 2007. They were calculated by multiplying POC/$^{234}Th_p$ ratios of sinking particles (larger than 0.7 ${\mu}m$) obtained from 150-200 m water depths to $^{234}Th$ fluxes that were estimated by integrating $^{234}Th/^{238}U$ disequilibrium from surface to 100 m water depth. Export fluxes ranged from 14 to 505 mg C $m^{-2}$ $day^{-1}$, with the highest value at station A2 and the lowest value at station D4. Primary production was well correlated with export flux, indicating that it was a major factor controlling export flux. Export flux in the East Sea was generally higher than those estimated in the open ocean and similar to or somewhat higher than those in the continental marginal seas. Export flux/primary production (EF/PP) ratios varied from 0.29 to 0.62, with an average of 0.43 and were somewhat higher in the basin area than in the coastal area. EF/PP ratio in the East Sea was rather similar to those estimated in the North Sea and Chukchi Sea, but much higher than those in the Labrador Sea, Barents Sea, and Gulf of Lions. Therefore, the East Sea is one of the major areas where a large amount of organic carbon produced in the euphotic zone sinks into the deep layer below 200 m water depth.

• Journal of the Korean Society of Radiology
• /
• v.85 no.3
• /
• pp.566-578
• /
• 2024

Purpose This study investigated whether the respiratory phase during pleural puncture in CT-guided percutaneous transthoracic needle biopsy (PTNB) affects complications. Materials and Methods We conducted a retrospective review of 477 lung biopsy CT scans performed during free breathing. The respiratory phases during pleural puncture were determined based on the table position of the targeted nodule using CT scans obtained during free breathing. We compared the rates of complications among the inspiratory, mid-, and expiratory respiratory phases. Logistic regression analysis was performed to control confounding factors associated with pneumothorax. Results Among the 477 procedures, pleural puncture was performed during the expiratory phase in 227 (47.6%), during the mid-phase in 108 (22.6%), and during the inspiratory phase in 142 (29.8%). The incidence of pneumothorax was significantly lower in the expiratory puncture group (40/227, 17.6%; p = 0.035) and significantly higher in the mid-phase puncture group (31/108, 28.7%; p = 0.048). After controlling for confounding factors, expiratory-phase puncture was found to be an independent protective factor against pneumothorax (odds ratio = 0.571; 95% confidence interval = 0.360-0.906; p = 0.017). Conclusion Our findings suggest that pleural puncture during the expiratory phase may reduce the risk of pneumothorax during image guided PTNB.

• Journal of Chest Surgery
• /
• v.41 no.5
• /
• pp.610-618
• /
• 2008

Background: There are various treatment modalities for atherosclerotic arterial obstructive disease at the lower limbs, for example, conservative physical therapy, medication, operation etc. Yet it has been established that an arterial bypass operation is the most effective treatment. The aim of this study is to evaluate the effect of arterial bypass operation within our experience and to determine the indicators of treatment. Material and Method: Ninety six patients received arterial bypass operation for atherosclerotic arterial obstructive disease from June 2002 to April 2006. We evaluated the feasibility of arterial bypass operation based on the improvement of symptoms and the ankle-brachial index (ABI) and the surgical outcomes, as based on the complications, the amputation rates and the patency rates. We also assessed the possible risk factors such as gender, age, a smoking history, co-morbidities, the anastomotic sites, the graft size and the graft type. We retrospectively reviewed the medical records of the patients. The total mean follow-up period was $29.4{\pm}13.1$ months. Result: The mean age was $65.95{\pm}9.61$ and there were 88 male patients. The most common clinical manifestation was ischemic resting pain in the lower extremities. The underlying combined diseases were hypertension (61%), diabetes (43%), cardiac problems (35%) and smoking (91.7%). The most frequent site of arterial obstruction was the superficial femoral artery (44 cases, 40%). A femoropopliteal artery bypass operation with a Polytetrafluoroethylene(PTFE) synthetic graft was done in 44 cases (40%) and the great saphenous vein graft was used in 11 cases. The postoperative ABI increased significantly from $0.30{\pm}0.11$ preoperatively to $0.63{\pm}0.11$ (p<0.001) postoperatively. In 8 cases, amputations above the ankle level were necessary. The graft patency rates were 86.4% and 68.0% after 1 and 3 years, respectively. There were 29 cases (30.21%) of patency failure; the male gender, smokers and hypertension were significantly more frequent in the failure group. Of these, hypertension was the most powerful risk factor (p=0.042). Conclusion: The arterial bypass operation is an effective treatment modality for controlling the symptoms such as pain and claudication, and for preventing major amputations for the patients with atherosclerotic arterial obstructive disease. This study suggests quitting smoking, strict blood pressure control, selection of an appropriate graft, regular outpatient follow up and proper medication would offer higher patency rates and more favorable outcomes.

• Journal of Global Scholars of Marketing Science
• /
• v.20 no.2
• /
• pp.135-148
• /
• 2010

Arab boycotts of Danish products, Australian boycotts of French products and Chinese consumer aversion toward Japanese products are all examples of how adverse actions at the country level might impact consumers' behavior. The animosity literature has examined how consumers react to the adverse actions of other countries, and how such animosity impacts consumers' attitudes and preferences for products from the transgressing country. For example, Chinese consumers are less likely to buy Japanese products because of Japanese atrocities during World War II and the unjust economic dealings of the Japanese (Klein, Ettenson and Morris 1998). The marketing literature, however, has not examined how consumers react to adverse actions committed by their own country against other countries, and whether such actions affect their attitudes towards purchasing products that originated from the adversely affected country. The social psychology literature argues that consumers will experience a feeling called collective guilt, in response to such adverse actions. Collective guilt stems from the distress experienced by group members when they accept that their group is responsible for actions that have harmed another group (Branscombe, Slugoski, and Kappenn 2004). Examples include Americans feeling guilty about the atrocities committed by the U.S. military at Abu Ghraib prison (Iyer, Schamder and Lickel 2007), and the Dutch about their occupation of Indonesia in the past (Doosje et al. 1998). The primary aim of this study is to examine consumers' perceptions of adverse actions by members of one's own country against another country and whether such perceptions affected their attitudes towards products originating from the country transgressed against. More specifically, one objective of this study is to examine the perceptual antecedents of collective guilt, an emotional reaction to adverse actions performed by members of one's country against another country. Another objective is to examine the impact of collective guilt on consumers' perceptions of, and preference for, products originating from the country transgressed against by the consumers' own country. If collective guilt emerges as a significant predictor, companies originating from countries that have been transgressed against might be able to capitalize on such unfortunate events. This research utilizes the animosity model introduced by Klein, Ettenson and Morris (1998) and later expanded on by Klein (2002). Klein finds that U.S. consumers harbor animosity toward the Japanese. This animosity is experienced in response to events that occurred during World War II (i.e., the bombing of Pearl Harbor) and more recently the perceived economic threat from Japan. Thus this study argues that the events of Word War II (i.e., bombing of Hiroshima and Nagasaki) might lead U.S. consumers to experience collective guilt. A series of three hypotheses were introduced. The first hypothesis deals with the antecedents of collective guilt. Previous research argues that collective guilt is experienced when consumers perceive that the harm following a transgression is illegitimate and that the country from which the transgressors originate should be responsible for the adverse actions. (Wohl, Branscombe, and Klar 2006). Therefore the following hypothesis was offered: H1a. Higher levels of perceived illegitimacy for the harm committed will result in higher levels of collective guilt. H1b. Higher levels of responsibility will be positively associated with higher levels of collective guilt. The second and third hypotheses deal with the impact of collective guilt on the preferences for Japanese products. Klein (2002) found that higher levels of animosity toward Japan resulted in a lower preference for a Japanese product relative to a South Korean product but not a lower preference for a Japanese product relative to a U.S. product. These results therefore indicate that the experience of collective guilt will lead to a higher preference for a Japanese product if consumers are contemplating a choice that inv olves a decision to buy Japanese versus South Korean product but not if the choice involves a decision to buy a Japanese versus a U.S. product. H2. Collective guilt will be positively related to the preference for a Japanese product over a South Korean product, but will not be related to the preference for a Japanese product over a U.S. product. H3. Collective guilt will be positively related to the preference for a Japanese product over a South Korean product, holding constant product judgments and animosity. An experiment was conducted to test the hypotheses. The illegitimacy of the harm and responsibility were manipulated by exposing respondents to a description of adverse events occurring during World War II. Data were collected using an online consumer panel in the United States. Subjects were randomly assigned to either the low levels of responsibility and illegitimacy condition (n=259) or the high levels of responsibility and illigitemacy (n=268) condition. Latent Variable Structural Equation Modeling (LVSEM) was used to test the hypothesized relationships. The first hypothesis is supported as both the illegitimacy of the harm and responsibility assigned to the Americans for the harm committed against the Japanese during WWII have a positive impact on collective guilt. The second hypothesis is also supported as collective guilt is positively related to preference for a Japanese product over a South Korean product but is not related to preference for a Japanese product over a U.S. product. Finally there is support for the third hypothesis, since collective guilt is positively related to the preference for a Japanese product over a South Korean product while controlling for the effect of product judgments about Japanese products and animosity. The results of these studies lead to several conclusions. First, the illegitimacy of harm and responsibility can be manipulated and that they are antecedents of collective guilt. Second, collective guilt has an impact on a consumers' decision when they face a choice set that includes a product from the country that was the target of the adverse action and a product from another foreign country. This impact however disappears from a consumers' decision when they face a choice set that includes a product from the country that was the target of the adverse action and a domestic product. This result suggests that collective guilt might be a viable factor for company originating from the country transgressed against if its competitors are foreign but not if they are local.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.23 no.3
• /
• pp.225-237
• /
• 1990

Various chemical constituents were measured from April to August 1988 at the down-ward 20 stations of Keum River, which is located in the Midwest of Korea, to understand the characteristics of water quality with respect to spatio-temporal variations of each constituent. The 24-hrs continuous measurements with 2-hrs interval were made simultaneously at station 2 near the estuary weir and station 9(Ganggyeong) of 35 km upstream from the weir in April. By the results observed for one day in April at station 2, salinity has a range of $7.88\~22.14\%_{\circ}$ and its temporal variability is identical to the pattern of tidal cycle in the neigh-bouring Kunsan Harbor. However, turbidity shows relatively high values only at an interval of 4~5 hours after the lowest salinity time, though hourly fluctuation of pH is very small. Silicate and dissolved inorganic nitrogen have inversively linear correlationships with salinity, implying the concentration of the two nutrients strongly regulated by estuarine mixing of sea and river waters. In contrast, phosphate sustains roughly a constant level over a wide salinity range and distinctly lower values than those corresponding to nitrate in the oceans. Such distributions of phosphate have been observed in some estuaries, and interpreted as driven by removal of dissolved phosphate into bottom sediments and the bufforing of phosphate by particulate matter. COD values at station 2 are relatively high in day-time(particularly afternoon) and in high-salinity periods. At station 9, saltwater intrusion was never found but water level changed to the extent of 2.5 m for one day. Although each parameter at this station exhibits very slight variations in their abundance for 24 hours compared with station 2, the contents of COD, silicate and ammonia are significantly higher than at station 2. Concentration of suspended matter is relatively high in the brackish water region up to $\~20$ km above the river mouth, probably due to strong tidal stirring of the bottom de-posits. Also, relatively high pH, COD and $O_2$ saturation at the upward stations of $40\~50$ km from the weir are presumably attributable to active photosynthesis of plants in the region. In general, COD and nutrients except phosphate are higher values at the upper stations than in the estuary zone, and show the highest abundances in July nearly at all stations. Finally, in the estuarine region tidal mixing of sea-river waters seems to be an important factor controlling the distributions of turbidity, COD, silicate and nitrate as well as salinity. However, water quality in the upward fresh-water zone is remarkably variable according to months or seasons.