• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.3
• /
• pp.1393-1405
• /
• 2017

It is well known that duty-cycling control by dynamically adjusting the polling interval according to the traffic loads can effectively achieve power saving in wireless sensor networks. Thus, there has been a significant research effort in developing polling interval adaptation schemes. Especially, Dynamic Low Power Listening (DLPL) scheme is one of the most widely adopted open-looping polling interval adaptation techniques in wireless sensor networks. In DLPL scheme, if consecutive idle (busy) samplings reach a given fixed threshold, the polling interval is increased (decreased). However, due to the trial-and-error based approach, it may significantly deteriorate the system performance depending on given threshold parameters. In this paper, we propose a novel DLPL scheme, called SDL (Sequential hypothesis testing based Dynamic LPL), which employs sequential hypothesis testing to decide whether to change the polling interval conforming to various traffic conditions. Simulation results show that SDL achieves substantial power saving over state-of-the-art DLPL schemes.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.495-502
• /
• 2013

In the mobile Ad hoc Network(MANET), improving technique for management and control of topology is recognized as an important part of the next generation network. In this paper, we proposed an efficient node life time management of ATICC(Adaptive Time Interval Clustering Control) in Ad-hoc Networks. Ad-hoc Network is a self-configuration network or wireless multi-hop network based on inference topology. This is a method of path routing management node for increasing the network life time through the periodical route alternation. The proposed ATICC algorithm is time interval control technique depended on the use of the battery energy while node management considering the attribute of node and network routing. This can reduce the network traffic of nodes consume energy cost effectively. As a result, it could be improving the network life time by using timing control method in ad-hoc networks.

• Journal of Power Electronics
• /
• v.13 no.1
• /
• pp.139-160
• /
• 2013

In this paper, an intelligent robust control system (IRCS) for precision tracking control of permanent-magnet synchronous motor (PMSM) servo drives is proposed. The IRCS comprises a recurrent wavelet-based interval type-2 fuzzy-neural-network controller (RWIT2FNNC), an RWIT2FNN estimator (RWIT2FNNE) and a compensated controller. The RWIT2FNNC combines the merits of a self-constructing interval type-2 fuzzy logic system, a recurrent neural network and a wavelet neural network. Moreover, it performs the structure and parameter-learning concurrently. The RWIT2FNNC is used as the main tracking controller to mimic the ideal control law (ICL) while the RWIT2FNNE is developed to approximate an unknown dynamic function including the lumped parameter uncertainty. Furthermore, the compensated controller is designed to achieve $L_2$ tracking performance with a desired attenuation level and to deal with uncertainties including approximation errors, optimal parameter vectors and higher order terms in the Taylor series. Moreover, the adaptive learning algorithms for the compensated controller and the RWIT2FNNE are derived by using the Lyapunov stability theorem to train the parameters of the RWIT2FNNE online. A computer simulation and an experimental system are developed to validate the effectiveness of the proposed IRCS. All of the control algorithms are implemented on a TMS320C31 DSP-based control computer. The simulation and experimental results confirm that the IRCS grants robust performance and precise response regardless of load disturbances and PMSM parameters uncertainties.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.51-58
• /
• 2000

It is well known that the majority of the emissions measured from vehicle exhaust in the US Federal Test Procedure(FTP-75) are emitted during the first 60 seconds. This paper describes an experimental study on SI engine emissions reduction after cold start with interval secondary air injection and coolant control. Secondary air injection after cold start to reduce exhaust emissions causes an exothermic reaction at the exhaust port and gives sufficient air to the catalyst. For that reason engine-out emissions oxidized in the exhaust port and the rapid heating of a catalytic converter after cold start with CSAI and ISAI are estimated. The influence of the coolant temperature on SI engine emissions has been estimated. In the present studycoolant control of the cylinder head tempeature is used to investigate the effect of coolant temperature on SI engine emissions. The results show that engine-out hydrocarbon and carbon monoxide emissions are considerably reduced with interval secondary air injection and coolant control.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.590-595
• /
• 2022

When a train is delayed because of a disturbance, the time interval deviation between successive trains increases, and high frequency metro lines can become unstable. Thus, it is necessary to control the traffic regularity to prevent any such instability. In this paper, we propose a simple but effective traffic regulation algorithm that gurantees system stability. In the proposed method, the control algorithm for running time is designed using a discrete traffic model where control input is determined from a linear combination of departure time deviations and control input of the preceding train to ensure an optimal time interval between successive trains. The results of the computer simulation are also given to demonstrate the validity of the proposed algorithm.

• Journal of Biosystems Engineering
• /
• v.21 no.2
• /
• pp.155-166
• /
• 1996

A direct injection sprayer was designed using the concepts of injection mixing and total flow control, flowrate-based system compensating for the variation of forwarding speed. A metered rate, proportionally to the actual diluent flow rate, of a tracer chemical was injected directly into the diluent stream. The injection of chemical may improve the precision and safety of chemical application process. The control system was evaluated for the variables of the control interval, tolerances and sensitivities of flow regulation valve and injection pump. Performance of the system was assessed as that the response time of flow rate, response time of injection rate, absolute steady state error, and the coefficient of variance(C.V.) of concentration were 8.5 and -0.53 seconds, 0.067 lpm(0.8%) and 3.15%, respectively, at optimal parameters of control interval of 1.0 sec, fast sensitivity of flow regulation valve, medium sensitivity of injection pump and medium tolerance of flow rate. Performance of the system can be improved by increasing the sensitivity of flow regulating valve and employing a high resolution velocimeter, such as Doppler radar.

• Journal of the Korea Safety Management & Science
• /
• v.9 no.2
• /
• pp.215-233
• /
• 2007

Even though the ad hoc Shewhart methods remain controversial due to various mathematical flaws, there is little disagreement among researchers and practitioners when a set of process data has a skewness distribution. In the context and language of process control, the error related to the process data shows that time to signal increases when a control parameter shifts to a skewness direction. In real-world industrial settings, however, quality practitioners often need to consider a skewness distribution. To address this situation, we developed an enhanced design method to utilize advantages of the traditional attribute control chart and to overcome its associated shortcomings. The proposed design method minimizes bias, i.e., an average time to signal for the shift of process from the target value (ATS) curve, as well as it applies a variable sampling interval (VSI) method to an attribute control chart for detecting a process shift efficiently. The results of the factorial experiment obtained by various parameter circumstances show that the VSI c control chart using nearly unbiased ATS design provides the smallest decreasing rate in ATS among other charts for all experimental cases.

• Corrosion Science and Technology
• /
• v.22 no.5
• /
• pp.377-386
• /
• 2023

Aircraft washing is performed periodically for corrosion control. Currently, the aircraft washing interval is qualitatively set according to the geographical conditions of each base. We developed a washing interval determination algorithm based on atmospheric corrosion environment monitoring data at the Republic of Korea Air Force (ROKAF) bases and United States Air Force (USAF) bases to determine the optimal interval. The main factors of the washing interval decision algorithm were identified through hierarchical clustering, sensitivity analysis, and analysis of variance, and criteria were derived. To improve the classification accuracy, we developed a washing interval decision model based on an artificial neural network (ANN). The ANN model was calibrated and validated using the atmospheric corrosion environment monitoring data and washing intervals of the USAF bases. The new algorithm returned a three-level washing interval, depending on the corrosion rate of steel and the results of the ANN model. A new base-specific aircraft washing interval was proposed by inputting the atmospheric corrosion environment monitoring results of the ROKAF bases into the algorithm.

• 한국데이터정보과학회:학술대회논문집
• /
• 2004.04a
• /
• pp.151-159
• /
• 2004

Properties of the variable sampling interval(VSI) control charts for monitoring dispersion matrix of related quality characteristics are investigated. Performances of the proposed charts are evaluated for matched fixed sampling interval(FSI) and VSI charts in terms of average time to signal(ATS) and average number of samples to signal (ANSS). Average number of swiches(ANSW) of the proposed VSI charts are also investigated.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1781-1790
• /
• 2016

This study focuses on the coordination control problem of multiple electrical excited synchronous motor systems. A robust coordination controller is designed on the basis of cross coupling and an interval matrix. The proposed control strategy can deal with load uncertainty. In addition, the proposed control strategy is applied to a high-power metal-rolling system. Simulation and experiment results demonstrate that the proposed control strategy achieves good dynamic and static performance. It also shows better coordination performance than traditional proportional-integral controllers.