• International Journal of Contents
• /
• v.14 no.1
• /
• pp.39-44
• /
• 2018

Today, cars have developed into intelligent automobiles that combine advanced control equipment and IT technology to provide driving assistance and convenience to users. These vehicles provide infotainment services to the driver, but this does not improve the safety of the driver. Accordingly, V2X communication, which forms a network between a vehicle and a vehicle, between a vehicle and an infrastructure, or between a vehicle and a human, is drawing attention. Therefore, various techniques for improving channel estimation performance without changing the IEEE 802.11p standard have been proposed, but they do not satisfy the packet error rate (PER) performance required by the C-ITS service. In this paper, we analyze existing channel estimation techniques and propose a new channel estimation scheme that achieves better performance than existing techniques. It does this by applying the updated matrix for the data pilot symbol to the construct data pilot (CDP) channel estimation scheme and by further performing the interpolation process in the frequency domain. Finally, through simulations based on the IEEE 802.11p standard, we confirmed the performance of the existing channel estimation schemes and the proposed channel estimation scheme by coded PER.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.3
• /
• pp.941-955
• /
• 2015

In dual-channel networks (DCNs), all frequency hopping (FH) sequences used for data channels are chosen from the original FH sequence used for the control channel by shifting different initial phases. As the number of data channels increases, the hitting frequency point problem becomes considerably serious because DCNs is non-orthogonal synchronization network and FH sequences are non-orthogonal. The increasing severity of the hitting frequency point problem consequently reduces the resource utilization efficiency. To solve this problem, we propose a novel hitting frequency point collision avoidance method, which consists of a sequence-selection strategy called sliding correlation (SC) and a collision avoidance strategy called keeping silent on hitting frequency point (KSHF). SC is used to find the optimal phase-shifted FH sequence with the minimum number of hitting frequency points for a new data channel. The hitting frequency points and their locations in this optimal sequence are also derived for KSHF according to SC strategy. In KSHF, the transceivers transmit or receive symbol information not on the hitting frequency point, but on the next frequency point during the next FH period. Analytical and simulation results demonstrate that unlike the traditional method, the proposed method can effectively reduce the number of hitting frequency points and improve the efficiency of the code resource utilization.

• Journal of KIISE:Computer Systems and Theory
• /
• v.29 no.7
• /
• pp.394-400
• /
• 2002

Networks of Workstations(NOWs), that has features of flexibility and scalability, recently has emerged as an inexpensive alternative to massively parallel multicomputers. However it is not easier to perform deadlock-free multicast than regular topologies like mash or hypercube. Single phase differential multicast(SPDM) is a modified multicast algorithm with less burden of the root node. By applying quality of serviece(QoS), a specific node can have differentiated service and artificial change of message flow pattern is also available. As the results of performance evaluation experiments, SPDM has lower latency and lower packet concentration rate of the root node than the case of SPAM, and has ability to control network load distribution among switch nodes by controlling the assignment rate among nodes.

• ETRI Journal
• /
• v.36 no.1
• /
• pp.31-41
• /
• 2014

The heterogeneous network (HetNet) has been discussed in detail in the Long-Term Evolution (LTE) and LTE Advanced standards. However, the standardization of High-Speed Packet Access HetNet (HSPA HetNet) launched by 3GPP is pushing at full steam. Interference coordination (IC), which is responsible for dealing with the interference in the system, remains a subject worthy of investigation in regard to HSPA HetNet. In this paper, considering the network framework of HSPA HetNet, we propose a quasi-distributed IC (QDIC) scheme to lower the interference level in the co-channel HSPA HetNet. Our QDIC scheme is constructed as slightly different energy-efficient non-cooperative games in the downlink (DL) and uplink (UL) scenarios, respectively. The existence and uniqueness of the equilibrium for these games are first revealed. Then, we derive the closed-form best responses of these games. A feasible implementation is finally developed to achieve our QDIC scheme in the practical DL and UL. Simulation results show the notable benefits of our scheme, which can indeed control the interference level and enhance the system performance.

• Journal of Korea Multimedia Society
• /
• v.9 no.7
• /
• pp.835-843
• /
• 2006

Multicast can send one copy of each packet to each member of the multicast group. Network resource is utilized effectively, consequently, it is suitable for one-to-many environments. reliability and flow control, however, are not supported basically, it is not suitable or transmission of multimedia data which have a time restriction. In this paper, we present a network model and a multicast retransmission scheme The proposed scheme remove ack-explosion from sender through local recovery and performs local retransmission when time restriction is satisfied on receiver by considering the state of receiver's buffer. Mathematical analysis and simulation are conducted to prove performance of the proposed scheme. The results are shown that the proposed scheme consumes a lower network bandwidth than the existing network model and guarantees QoS of receivers.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.5
• /
• pp.983-989
• /
• 2012

IEEE 802.3az LPI mechanism allows an Ethernet link to reduce power consumption by entering a low-power sleeping mode and letting some components being powered off when there is no data to be transmitted through the link. However, if small amount of packets are being sent periodically, such a mechanism can not obtain energy efficiency due to a high overhead caused by excessive mode transitions. In this paper, we propose an enhanced LPI mechanism which can perform state transition adaptively based on the traffic characteristics on transport layer and network status. This simulation result shows that proposed mechanism improves energy efficiency than LPI mechanism with respect to energy consumption rate for various traffic loads.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.5
• /
• pp.181-190
• /
• 2013

PMIPv6(Proxy Mobile IPv6) is a network-based IP mobility management protocol, which can control the mobility without depending on the type of access system or the capability of mobile node. Combining it with SIP mobility, it can establish the route optimization effectively and ensure the terminal mobility and the session mobility. There are many literatures on PMIPv6-SIP in mobility management, but efficient performance analysis and mathematical modeling has not been standardized. For this, a new PMIPv6-SIP architecture is proposed to compare with Pure-SIP in terms of the handover delay and packet loss.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.1928-1934
• /
• 2014

Induction motors are widely used due to their rugged, robust and easy to care features. Since they are heavily used in industry, testing of three phase induction motors have play a vital role. In order to determine motor equivalent circuit parameters, efficiency of motor, squirrel caged laboratory sized an induction motor test setup is prepared. It is suitable for the induction motor with the frame size of 100 and 112. A virtual Instrumentation typed engineering workbench (called as LabVIEW) software packet, is utilized as a graphical user interface program. Motor input power is measured by measuring the input voltage, current and power factor with the help of hall effect typed voltage and current transformers. Also, the output power is measured by measuring the speed and torque with the help of an encoder and torque sensor. All outputs of the voltage and current transformer, encoder and temperature, torque sensors are given to the Data Acquisition Card (DAQ) which acquires the data for processing and then the equivalent circuit parameters, efficiency, performance and loading characteristics are found out, using LabVIEW based user interface. It is suggested to use this test rig for the quality control of produced motors in industry, and an educational experiment setup in the school laboratories.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.7
• /
• pp.2354-2370
• /
• 2015

The advantages of employing SCTP-based Concurrent Multipath Transfer (CMT) have been demonstrated to be very useful for data delivery over multi-homed wireless networks. However, there is still significant ongoing work addressing some remaining limitations and challenges. The most important concern when applying CMT to data delivery is related to handling packet reordering and buffer blocking. Another concern on this topic is that current sender-based CMT solutions seldom consider balancing the overhead and sharing the load between the sender and receiver. This paper proposes a novel Receiver-driven Cooperation-based Concurrent Multipath Transfer solution (CMT-Rev) with the following aims: (i) to balance overhead and share load between the sender and receiver, by moving some functions including congestion and flow control from the sender onto receiver; (ii) to mitigate the data reordering and buffer blocking problems, by using an adaptive receiver-cooperative path aggregation model, (iii) to adaptively transmit packets over multiple paths according to their receiver-inspired sending rate values, by employing a new receiver-aware data distribution scheduler. Simulation results show that CMT-Rev outperforms the existing CMT solutions in terms of data delivery performance.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.7
• /
• pp.1585-1609
• /
• 2013

Over recent years, enormous amounts of research in wireless sensor networks (WSNs) have been conducted, due to its multifarious applications such as in environmental monitoring, object tracking, disaster management, manufacturing, monitoring and control. In some of WSN applications dependent the energy-efficient and link reliability are demanded. Hence, this paper presents a routing protocol that considers these two criteria. We propose a new mechanism called Reliable Routing Scheme for Energy-Balanced (RRSEB) to reduce the packets dropped during the data communications. It is based on Swarm Intelligence (SI) using the Ant Colony Optimization (ACO) method. The RRSEB is a self-adaptive method to ensure the high routing reliability in WSNs, if the failures occur due to the movement of the sensor nodes or sensor node's energy depletion. This is done by introducing a new method to create alternative paths together with the data routing obtained during the path discovery stage. The goal of this operation is to update and offer new routing information in order to construct the multiple paths resulting in an increased reliability of the sensor network. From the simulation, we have seen that the proposed method shows better results in terms of packet delivery ratio and energy efficiency.