• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.9
• /
• pp.54-61
• /
• 2016

A 6-Gbps single-ended receiver with a linear equalizer and a self-reference generator is proposed for a high-speed interface with the double data rate. The proposed single-ended receiver uses a common gate amplifier to increase a voltage gain for an input signal with low voltage level. The continuous-time linear equalizer which reduces gain to the low frequencies and achieves high-frequency peaking gain is implemented in the common gate amplifier. Furthermore, a self-reference generator, which is controlled with the resolution 2.1 mV using digital averaging method, is implemented to maximize the voltage margin by removing the offset noise of the common gate amplifier. The proposed single-ended receiver is designed using a 65-nm CMOS process with 1.2-V supply and consumes the power of 15 mW at the data rate of 6 Gbps. The peaking gain in the frequency of 3 GHz of the designed equalizer is more than 5 dB compared to that in the low frequency.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.71-79
• /
• 2013

This paper describes a 12.5 Gb/s low-power receiver design with equalizer adaptation. The receiver adapts to channel and chip process variation by adaptation circuit using sampler and serializer. The adaptation principle is explained. It describes technique receiving ground referenced differential signal of voltage-mode transmitter for low-power. The CTLE(Continuous Time Linear Equalizer) having 17.6 dB peaking gain to remove long tail ISI caused channel with -21 dB attenuation. The voltage margin is 210 mV and the timing margin is 0.75 UI in eye diagram. The receiver consumes 0.87 mW/Gb/s low power in 45 nm CMOS technology.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.155-167
• /
• 2015

An adaptive equalization scheme based on all-digital jitter measurement is proposed for a continuous time linear equalizer (CTLE) preceding a clock and data recovery (CDR) in a receiver circuit for high-speed serial interface. The optimum equalization coefficient of CTLE is determined during the initial training period based on the measured jitter. The proposed circuit finds automatically the optimum equalization coefficient for CTLE with 20", 30", 40" FR4 channel at the data rate of 5 Gbps. The chip area of the equalizer including the adaptive controller is 0.14 mm2 in a $0.13{\mu}m$ process. The equalizer consumes 12 mW at 1.2 V supply during the normal operation. The adaptive equalizer has been applied to a USB3.0 receiver.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.87-95
• /
• 2014

This paper describes a dual channel receiver design for CIS interfaces. Each channel includes CTLE(Continuous Time Linear Equalizer), sampler, deserializer and clocking circuit. The clocking circuit is composed of PLL, PI and CDR. Fast lock acquisition time, short latency and better jitter tolerance are achieved by adding OSPD(Over Sampling Phase Detector) and FSM(Finite State Machine) to PI-based CDR. The CTLE removes ISI caused by channel with -6 dB attenuation and the lock acquisition time of the CDR is below 1 baud period in frequency offset under 8000ppm. The voltage margin is 368 mV and the timing margin is 0.93 UI in eye diagram using 65 nm CMOS technology.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.433-448
• /
• 2012

A source-synchronous receiver based on a delay-locked loop is presented. It employs a shared global calibration control between channels, yet achieves channel expandability for high aggregate I/O bandwidth. The global calibration control accomplishes skew calibration, equalizer adaptation, and phase lock of all the channels in a calibration period, resulting in the reduced hardware overhead and area of each data lane. In addition, the weight-adjusted dual-interpolating delay cell, which is used in the multiphase DLL, guarantees sufficient phase linearity without using dummy delay cells, while offering a high-frequency operation. The proposed receiver is designed in the 90-nm CMOS technology, and achieves error-free eye openings of more than 0.5 UI across 9-28 inch Nelco4000-6 microstrips at 4-7 Gb/s and more than 0.42 UI at data rates of up to 9 Gb/s. The data lane occupies only $0.152mm^2$ and consumes 69.8 mW, while the rest of the receiver occupies $0.297mm^2$ and consumes 56.0 mW at the 7- Gb/s data-rate and supply voltage of 1.35 V.