• 열처리공학회지
• /
• 제17권5호
• /
• pp.283-292
• /
• 2004

The effects of the annealing parameters on microstructures were examined in a cold-rolled high strength steel containing 0.1% C, 0.5% Si, 1.5% Mn, and 0.04% Nb. It was impossible to avoid martensite in the microstructure even though the continuous annealing parameters were controlled. This indicates that the alloying elements such as silicon and manganese contributing to manganese equivalent($Mn_{eq}$) should be reduced to produce the ferrite-pearlite microstructure for the solid solution and precipitation hardened steel. It was found that a decrease in the rapid cooling temperature to $520^{\circ}C$ was effective to change the microstructure from ferrite-martensite to ferrite-pearlite-martensite. Typical dual-phase properties exhibiting a low yield ratio and a continuous yielding behavior were obtained when the rapid cooling temperature was in the range of $680^{\circ}C$ to $600^{\circ}C$. The critical volume fraction of martensite for the typical properties of dual-phase steel was about 11 percent.

• 열처리공학회지
• /
• 제26권5호
• /
• pp.241-247
• /
• 2013

Hardenability and mechanical properties of boron-bearing steels containing C, Mo and Cr were investigated in this study. Using quench dilatometer, the steel specimens were cooled down to room temperature at different cooling rates to construct continuous cooling transformation diagrams and then the transformation products from austenite were examined. A critical cooling rate was introduced as an index to quantitatively evaluate the hardenability. The C addition to boron-bearing steels did not significantly affect hardenability compared to boron-free steels although it increases the hardenability. With the same content, the Mo addition largely increased the hardenability of boron-bearing steels than the Cr addition because it decreased both the transformation start and finish temperatures at low cooling rates. In particular, the Mo addition completely suppressed the formation of eutectoid ferrite even at the slow cooling rate of $0.2^{\circ}C/s$, whereas the Cr addition nearly suppressed it at the cooling rates above $3^{\circ}C/s$.

• 한국분말재료학회지
• /
• 제22권1호
• /
• pp.10-14
• /
• 2015

In recent years, industrial demands for superior mechanical properties of powder metallurgy steel components with low cost are rapidly growing. Sinter hardening that combines sintering and heat treatment in continuous one step is cost-effective. The cooling rate during the sinter hardening process dominates material microstructures, which finally determine the mechanical properties of the parts. This research establishes a numerical model of the relation between various cooling rates and microstructures in a sinter hardenable material. The evolution of a martensitic phase in the treated microstructure during end quench tests using various cooling media of water, oil, and air is predicted from the cooling rate, which is influenced by cooling conditions, using the finite element method simulations. The effects of the cooling condition on the microstructure of the sinter hardening material are found. The obtained limiting size of the sinter hardening part is helpful to design complicate shaped components.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1261-1266
• /
• 2008

Experimental study was performed to understand the operations of a showcase working in a discount store. Temperatures of evaporation, condenser were measured and also electric power consumption of compressor were measured. The purpose of this study is to application use of cold-heat storage systems operated the showcase. At the condition using ice storage system, the ice making process was operated during midnight being not needed the cooling of the showcase through the continuous running of the condenser unit. And then, the refrigerant was sub-cooled using stored cold-heat after being discharged from the air cooling condenser during the day time. The cooling performance was increased owing to the sub-cooling of refrigerant during day time, hence the running time of the compressor was effectively decreased. In other words, this study showed that power consumption during daytime can be transferred to the midnight for making use of the refrigerant sub-cooling. So the operating characteristics of the showcase system under various working conditions were analyzed and discussed.

• 한국초전도ㆍ저온공학회논문지
• /
• 제10권3호
• /
• pp.27-31
• /
• 2008

In order to cool the SMES coil to the operating temperature, conduction cooling is generally used. However, it often consumes a large amount of electric power because of it's continuous cryocooler operation. This can also lead to poor thermal stability and serious protection problems of the system. Solid nitrogen (SN2) can counter those disadvantages in the conduction cooling system because it has a large heat capacity. Particularly, a large amount of enthalpy with a minimal weight to the cold body of SN2 makes a compact and portable system by increase a recooling to recooling time period (RRTP) value. A conceptual design of the proto-type SN2 cooling system for a portable HTS superconducting magnetic energy storage (SMES) system will be introduced in this paper.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.71-72
• /
• 2006

• 한국재료학회지
• /
• 제4권1호
• /
• pp.44-54
• /
• 1994

Ti, Nb B를 합금원소로 첨가한 알루미늄 킬드 극저탄소 고강도 강판의 재결정 집합조직에 미치는 코일링처리시의 냉각속도, 냉간가공도, 연속어닐링처리등의 효과를 조사하였다. 집합조직계수비 TC(222)/TC(200)는 코일링시의 냉각속도 감소와 냉간압연시의 입하율 증가에 따라 증가하는 경향을 나타내었다. 그러나 압하율이 80%에서 90%로 증가됨에 따라 집합조직계수비가 오히려 감소하는 경향을 나타내는데, 이것은 주집합조직이 {554}<225>로부터 {111}<112>로부터 {111}<112>로 바뀌기 때문인것으로 보여진다. 집합조직계수비를 최대로 만들기위한 최적의 강판제조 공정 조건을 제시하면, 코일링처리시 노냉하고, 냉간압연시의 압하율은 80%로 하며, 연속열처리시 $800^{\circ}C$에서 1분간 유지한다음 $20^{\circ}C$로 수냉하고 다시 $450^{\circ}C$에 5분간 과시효처리하는 것이다.

• 설비공학논문집
• /
• 제13권12호
• /
• pp.1236-1244
• /
• 2001

In the present study, the possibility of continuous slurry ice making using flowing water solution in a cooled tube has been investigated. The experiments were carried out at various concentration and velocity of water solution, temperature of cooled tube wall, and control pressure in a tube. As a result, four types of operating conditions, that is super-cooling, continuous ice making, intermittent ice making and ice blockage, were classified. And it was found that the critical condition for the continuous ice making was acquired as a function of these experimental parameters.

• 한국주조공학회지
• /
• 제20권2호
• /
• pp.80-88
• /
• 2000

Continuous casting equipment was designed to cast the metallic uranium rods, and a thermal analysis was carried out to calculate the temperature and solidification profiles. Fluid flow and heat transfer analysis model including the effects of phase change was used to simulate the continuous casting process by finite volume method. In the design of continuous casting equipment, the casting speed, pouring temperature and cooling conditions should be considered as significant factors. In this study, the effects of casting speed, pouring temperature, and air gap between the uranium and mold were investigate. The results represented that the temperature and solidification profiles of continuous casting equipment varied with the casting speed, pouring temperature, and air gap.

• 한국전기전자재료학회논문지
• /
• 제16권12S호
• /
• pp.1278-1285
• /
• 2003

This study investigated the phase transformation of the REBa$_2$Cu$_3$$O_{7-x}$ (RE=Nd, Gd, Dy) superconductor, and CCT (Continuous-Cooling-Transformation) along with the TTT (Time-Temperature-Transformation) diagrams are suggested according to the isothermal and continuous cooling heat-treatments. The peritectic temperature of the 123 phases decreased approximately 3$0^{\circ}C$ when the ionic radius of the rare-earth elements was reduced. The optimum cooling rate where BC and Cu-free phases do not exist was 0.001$^{\circ}C$/s. At this cooling late, the 123 phase grew with a c-axis Perpendicular to the surface and had a well-distributed 211 phase. When the oxygen partial pressure was reduced Outing isothermal heat-treatment, the formation temperature of the 211 phase decreased. In addition, the formation temperature of the 123 phases decreased from 100$0^{\circ}C$ (Nd-123) to 9$25^{\circ}C$ (Gd-123), and finally 875$^{\circ}C$ (Dy-123) according to the decrease in the ionic radius of the tare-earth elements. Compared to Nd-123, Gd- and Dy-123 had a better texture with a well-distributed 211 phase.e.