• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.3
• /
• pp.74-80
• /
• 2004

If the withdrawal force of strand driven roll which is controlled with predetermined speed isn't distributed regularly in continuous casting process, mold level is changed cyclically and slab quality is not good. In this paper, both casting speed control and load sharing control algorithm of strand driven roll according to ratio which is set up by operator at same time is proposed. The proposed algorithm is to share the withdrawal force by following torque current of each driven roll as average torque current by changing speed reference of each driven roll motor. The load sharing control with anti-wind up for improvement transient state is adopted and the proposed algorithm is implemented in POSCO pilot caster.

• Transactions of Materials Processing
• /
• v.4 no.3
• /
• pp.233-244
• /
• 1995

Rolling force in the direct rolling(or twin-roll strip continuous casting) process fo semi-solid material has been computed using rigid-viscoplastic finite element method. Temperature distributions for calculations of rolling force and roll deformation are obtained from thermofluid analysis. Three dimensional roll deformation analysis has also been performed by using commercial package ANSYS. From the results, behavior of metal flow, rolling force and roll deformation have been investigated according to the process conditions of semi-solid direct rolling.

• Journal of Korea Foundry Society
• /
• v.43 no.2
• /
• pp.55-63
• /
• 2023

Due to the importance of the surface on the final slab quality, it is essential to maintain a smooth segment roll surface that is in touch with the thin solid shell during solidification. In this paper, the surface of the used continuous casting guide roll was analyzed to realize the mechanism of its surface deterioration. Surface analysis has revealed severe corrosion at two distinct areas leading to deep roughness occurring on the guide roll. Firstly, the severe corrosion follows prior austenite grain boundary due to exposure with acidic environment. Also, in heat affected zone (HAZ) where two cladding beads overlap, more severe corrosion takes place. The overheat input results in local ferritization without full melting which increases retained δ-ferrite content almost 10 times higher than surrounding area. Corrosion was observed to happen at the δ-γ interface where Cr depletion takes place.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.12
• /
• pp.73-85
• /
• 1997

The rolling force and roll deformation behavior in the twin roll type strip continuous casting process has been computed to estimate the thermal charcteristics of a caster roll. To calculation of rolling force, the relationship between flow stress and strain for a roll material and casting alloy are assumed as a function of strain-rate and temperature because mechanical properties of a casting materials depends on tempera- ture. The three dimensional thermal dlastic-plastic analysis of a cooling roll has also been carried out to obtain a roll stress and plastic strain distributions with the commercial finite element analysis package of ANSYS. Temperature fields data of caster roll which are provided by authors were used to estimated of roll deformation. Roll life considering thermal cycle is calculated by using thermal elastic-plastic analysis results. Roll life is proposed as a terms of a roll revolution in the caster roll with and without fine failure model on the roll surface. To obtain of plastic strain distributions of caster roll, thermomechan- ical properties of roll sleeve with a copper alloy is obtained by uniaxial tensile test for variation of temperature.

• Corrosion Science and Technology
• /
• v.20 no.5
• /
• pp.315-323
• /
• 2021

In this study, we examined corrosion behaviors of two types of Pb alloys for a lead acid battery comparatively. One containing 6.6 wt% Sn, 36 mg/kg Bi, and 612.4 mg/kg Ca was prepared by twin-roll continuous casting. The other containing 5.2 wt% Sn, 30.5 mg/kg Ag, and 557 mg/kg Ca was made by twin-belt continuous casting. Potentiodynamic polarization tests were performed to evaluate corrosion resistance. Cyclic voltammetry was done to examine oxidation and reduction reactions occurring on the surface of each alloy in 4.8 M H₂SO₄ solution. Electrochemical test results implied that the Pb alloy prepared with the twin-belt casting method was less stable than that cast with the twin-roll method. Such results might be due to precipitations formed during the casting process. Rolling did not appear to affect the corrosion behavior of the twin-roll samples with Ag < 10 mg/kg, while it reduced the anodic reaction of Ag on the surface of the twin-belt sample with 30.5 mg/kg Ag.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.274-278
• /
• 1992

냉간압연기술의 발달로 냉간압연기도 매우 다양하게 발달되었으며 냉간압연의 원자재인 열간압연재의 종류도 다양하다. 최근 열간압연가공시 회수율이 높은 연속주조재(Continuous casting strip)인 CC 재가 종전의 가공과정이 복잡하며 불량율이 높은 Ingot주조재(Ingot casting strip)인 IC 재 보다 생산비율이 점차 증대되어 냉간압연재료의 주종을 차지하고있다. CC재는 냉간압연가공시 IC재에 비해 Work roll 조도저하가 현저하게 크기 때문에 슬립(Slip)과 채팅(Charttering) 현상 등이 발생하여 압연가공성이 불안정 하게 되어 Work roll과 판표면에 손상이 생기게 되고, 압연가공시 Roll 사고 등의 문제가 발생하므로 Roll 마멸의 정도를 파악하여 Roll을 효과적으로 관리하므로써 Work roll과 판표면의 슬립현상 및 채터 링현상 등을 방지할 수 있다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.30-34
• /
• 2000

In this paper we analyzed bulging condition which affect the quality of continuous casting steel by using the numerical analytic method. First solidification analyses are performed for each cooling zones. Solidification analysis are carried out by one-dimensuional finite difference method. The bulging deformation of cast slab has been calculated with a two-dimensional elasto-plastic and creep finite element model. The adequacy of the model has been checked against the experimental results. From this study the effects of the process variables such as casting speed cooling condition roll pitch are examined. The results from these analyses would be able to apply to the design of continuous casting process.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.11
• /
• pp.122-128
• /
• 2000

In this paper, a bulging condition which affect the quality of continuous casting steel was analyzed by using the numerical analytic method. First, solidification analyses were performed for each cooling zone by one-dimensional finite difference method. The bulging deformation of cast slab has been calculated with a two-dimensional elasto-plastic and creep finite element model. The adequacy of the model has been checked against the experimental results. From this study the effects of the process variables such as casting speed, cooling condition and roll pitch were examined. The results from these analyses would be able to apply to the design of continuous casting process.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.2
• /
• pp.70-76
• /
• 2004

In the steel marking industry, most companies have adapted the continuous casting process, due to its economical benefit. Casting rolls are utilized for frictional drive and the transport of solidifying slap. Dimensional tolerances, mechanical stability, and surface condition of the casting rolls can affect both the surface and the internal quality of the product being cast. To overcome these problems, the industry now is focused on accelerating the rate of technological improvements. This study has been undertaken for the development of casting rolls overlaid materials (SAW FCW wire), with the addition of Vanadium and Molybdenum to the martensitic stainless steel, in order to increase tensile strength and hardness at elevated temperatures.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.913-922
• /
• 1987

In this paper the solidification phenomena at the molten pool has been modeled and simulated in terms with the one dimensional unsteady-state heat transfer of the solid and molten phase and the pressure distribution in the solid phase for the twin-roller continuous casting of Sn-15% Pb. The further purpose of this study was to effectively analyze the thermal and mechanical deformation of roll applying the results of the heat transfer and the pressure distribution to the boundary conditions. The strip thickness of rapidly solidified metallic strip decreases with increasing angular velocity of the roller and with increasing initial roll gap. For this reason the roll spacing and angular velocity of the rolls are considered to be main variables. The recommended optimal casting regimes for continuous strip dimensions is near 0.8mm-1.0mm in thickness at the given angular velocity .omega.=2.0 rad/sec. Results of the experiment using Sn-15% Pb are compared with model predictions. The calculated roll deformation has been in good agreement with the observed value of roll deformatiion. All the deformation. All the deformation of the roller is within the elastic range, the plastic yielding are not occured. However, these elastic stresses are sufficient to take place of the shortened roller life by the thermal fatigue and a notch fatigue. The higher cooling rates were obtained by a twin-roller quenching technique. Also the quenched microstructure of the rapidly solidified shell was verified.