• Structural Engineering and Mechanics
• /
• 제38권4호
• /
• pp.385-403
• /
• 2011

Continuous deep girders which transmit the gravity load from the upper wall to the lower columns have frequently long end shear spans between the boundary of the upper wall and the face of the lower column. This paper presents the results of tests and analyses performed on three 1:2.5 scale specimens with long end shear spans, (the ratios of shear-span/total depth: 1.8 < a/h < 2.5): one designed by the conventional approach using the beam theory and two by the strut-and-tie approach. The conclusions are as follows: (1) the yielding strength of the continuous RC deep girders is controlled by the tensile yielding of the bottom longitudinal reinforcements, being much larger than the nominal strength predicted by using the section analysis of the girder section only or using the strut-and-tie model based on elastic-analysis stress distribution. (2) The ultimate strengths are 22% to 26% larger than the yielding strength. This additional strength derives from the strain hardening of yielded reinforcements and the shear resistance due to continuity with the adjacent span. (3) The pattern of shear force flow and failure mode in shear zone varies depending on the amount of vertical shear reinforcement. And (4) it is necessary to take into account the existence of the upper wall in the analysis and design of the deep continuous transfer girders that support the upper wall with a long end shear span.

• Journal of Mechanical Science and Technology
• /
• 제17권4호
• /
• pp.477-483
• /
• 2003

An independent kinematic hardening material model in which the reverse yielding point is defined by the Bauschinger effect factor (BEF) , has been defined for stainless steel SUS 304. The material model and the BEF are obtained experimentally and represented mathematically as continuous functions of effective plastic strain. The material model has been incorporated in a non-linear stress analysis for the prediction of reverse yielding in thick-walled cylinders during the autofrettage process of these vessels. Residual stress distributions of the independent kinematic hardening material model at the onset of reverse yielding are compared with residual stresses of an isotropic hardening model showing the significant effect of the BEF on reverse yielding predictions. Critical pressures of direct and reverse yielding are obtained for the most commonly used cylinders and a range of permissible internal pressures for an efficient autofrettaged process is recommended.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.928-929
• /
• 2006

Tensile stress-strain and dynamic acoustic resonance tests were performed on Fe-C-Ni-Cu-Mo high-strength steels, characterized by a heterogeneous matrix microstructure and the prevalence of open porosity. All materials display the first yielding phenomenon and, successively, a continuous yielding behavior. This flow behavior can be described by the Ludwigson equation and developes through three stages: the onset of localized plastic deformation at the pore edges; the evolution of plastic deformation at the pore necks (where the austenitic Ni-rich phase is predominant); the spreading of plastic deformation in the interior of the matrix. The analytical modeling of the strain hardening behavior made it possible to obtain the boundaries between the different deformation stages.

• 열처리공학회지
• /
• 제28권4호
• /
• pp.171-180
• /
• 2015

The variation in microstructure and texture during continuous annealing was examined in a series of 1.6% Mn-0.1% Cr-0.3% Mo-0.005% B steels with carbon contents in the range of 0.010 to 0.030%. It was found that microstructure of hot band consisted of ferrite and pearlite as a consequence of high coiling temperature, and eutectoid carbon content was between 0.011% and 0.016%. Martensite ranged in volume fraction from 1.5% to 4.0% when annealed at $820{\circ}C$ according to the typical continuous annealing cycle. The critical martensite content for the continuous yielding was about 4% from stress-strain curves. The continuous yielding was obtained in the 0.030% carbon steel and 0.010% to 0.020% carbon steels revealed some yield point elongation ranging from 0.8% to 2.2% in as-annealed conditions. Higher tensile strength in the higher carbon steel is due to both increase in the martensite volume fraction and ferrite grain refinement. Decreasing the carbon content to 0.01% strengthened the intensities of ${\gamma}$-fiber textures, resulting in the increase in the $r_m$ value, which was caused by the lower volume fraction of martensite. The higher carbon steels showed the lower $r_m$ value of about 1.0.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.53-56
• /
• 2003

The disappearance of continuous yielding and the formation of an extended region in engineering stress-strain curves at tempering temperatures of 673-873K is closely related to the reduction of mobile dislocations during tempering and dynamic recovery during tensile deformation. In addition, the occurrence of discontinuous yielding at tempering temperature above 923K would be attributed to the formation of new strain-free polygonal ferrite grain.

• 소성∙가공
• /
• 제12권8호
• /
• pp.744-749
• /
• 2003

The effect of tempering temperatures on microstructures and mechanical properties was studied in a low carbon steel. The disappearance of continuous yielding and the formation of an extended region in engineering stress-strain curves at tempering temperatures ranging from 673 to 873K was caused by the reduction of mobile dislocations during tempering and dynamic recovery during tensile deformation. In addition, the occurrence of discontinuous yielding in the sample treated at the tempering temperatures above 923K was attributed to the formation of new strain-free polygonal ferrite grain.

• 한국재료학회지
• /
• 제30권6호
• /
• pp.315-320
• /
• 2020

This study deals with the yielding behavior and strain aging properties of three bake hardening steels with dual-phase microstructure, fabricated by varying the annealing temperature. Bake hardening and aging tests are performed to examine the correlation of martensite volume fraction with yielding behavior and strain aging properties of the bake hardening steels with dual-phase microstructure. The volume fraction of martensite increases with increasing annealing temperature. Room-temperature tensile test results show that the yielding behavior changes from discontinuous-type to continuous-type with increasing volume fraction of martensite due to higher mobile dislocation density. According to the bake hardening and aging tests, the specimen with the highest fraction of martensite exhibited high bake hardening with low aging index because solute carbon atoms in ferrite and martensite effectively diffuse to dislocations during the bake hardening test, while in the aging test they diffuse at only ferrite due to lower aging temperature.

• 한국강구조학회 논문집
• /
• 제11권2호통권39호
• /
• pp.213-222
• /
• 1999

ALFD방법은 연속합성판형교의 과재하중과 최대하중에 대한 강도검토에 있어서 실제적인 거동을 나타낼 수 있는 탄소성해석법이다. 주어진 하중으로 인한 최대 정, 부모멘트단면에서의 항복은 활하중이 통과한 후에 잔류하는 소성회전을 일으킨다. 또한 제조시의 잔류응력으로 인하여 이론적인 항복모멘트 이하에서도 소성변형을 일으킨다. 이러한 국부항복은 다음에 작용되는 과재하중하에서 탄성화되어 정의 자생모멘트를 유발한다. 본 연구에서는 지점과 최대 정모멘트 단면에서의 단위소성회전각으로 인한 자생모멘트를 공액보법과 3연모멘트법에 의하여 구하였고, 9개의 설계경간을 지점단면을 감소시켜가면서 본 연구에서 개발한 전산프로그램에 의하여 연속관계와 모멘트-비탄성회전각 실험곡선과 일치하는 자생모멘트를 구하였다. 또한 한국도로교시방서에 준하여 비조밀단면을 갖는 3경간 연속합성판형교의 평가를 수행하였다.

• ALGAE
• /
• 제17권2호
• /
• pp.127-133
• /
• 2002

The red seaweed Eucheuma serra is a high yielding source of lectins. The plants were collected from a depth of 5-6 meters and cultured in the laboratory, field and deep seawater. A Daily Growht Rate (DGR) of 3.5% was observed at 18℃ with a low light of 30μmol photon $ m^{-2} · s^{_1}$ in the laboratory. When the plants were cultured in the field at different depths during winter onths of December and January, best growth was observed at 1 m depth and a DGR of 2.14±0.04% was recorded. The plants grown in the tank with a continuous supply of deep seawater showed a DGR of 8.2% The results indicate that E. serra can be cultivated in large scale both in deep seawater in the tank and in the field for the extraction of lectins at a commercial scale.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.393-396
• /
• 2006

One of the important aspects of ductility is redistribution. To see the difference of redistribution between reinforced concrete members and prestressed concrete beams, two span continuous concrete beams are tested. From the test results, we can get important information on the redistribution ratio. After occurrence of crack at support section, the redistribution ratio increased and after yielding they fluctated very much. Compare with reinforced concrete, the redistribution ratio of prestressed concrete beam changed more abruptly after yielding. Both of the them show limited redistribution up to 70%.