• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.896-905
• /
• 1993

Thin-layers of wheat and barley are dried at near-ambient temperatures(3.5$^{\circ}C$ -5$0^{\circ}C$) in order to obtain the intrinsic drying data. The well established apparatus was modified to enable it to record all the sample weight data in still air by using a purpose -built automatically controlled sliding valve. The air could be diverted in less than 0.5seconds and a 7 second period was required to attain a steady weight reading. With this apparatus, very smooth drying curves were obtained. The data of sample weight , drying temperature and dew point temperature wee recorded continuously . The drying process was terminated when the moisture content change in 24 hours was less than 0.004 d.b. This was achieved by drying a sample for about a week . The final points were recorded as the dynamic equilibrium moisture content(EMC). The drying data were than fitted to the exponential Newton model and the dynamic EMC data were fitted to the Modified-Chung-Pfost Model . All the fitted parameters are given and comparison is made with previous published data. The comparisons who that the current drying constants are lower than the previous data, the dynamic EMC data obtained for wheat and barely agree with the previous data. The results show that to obtain the drying constant in the exponential Newton model, adequate drying time is necessary.

• KSBB Journal
• /
• v.23 no.2
• /
• pp.169-176
• /
• 2008

The concentration of fresh gel from Aloe vera L. by using ulfrafiltration (UF) process was investigated and analyzed. The two membranes (organic and ceramic) with different molecular weight cut-off (MWCO) and modules (flat sheet and tubular) was used. Under optimum operation conditions, ceramic (zirconium dioxide) tubular membrane with MWCO of 50 kDa resulted in higher flux, less fouling, more turbid, higher total solid, higher polysaccharide and less aloin content. Optimum operation conditions were transmembrane pressure of 1.0 bar, feed velocity of 240 L/hr and temperature of $23^{\circ}C$. Volume concentration factor of aloe gel was 3.13 at permeate flux of $51.1\;L/m^2{\cdot}hr$ after processing time of 1.66 hr. Aloin in fresh aloe gel by UF process was effectively removed as permeate and bioactive polysaccharide content was 2.1 times higher than that of fresh aloe gel. These results allowed a very good level of concentration degree and polysaccharide content. Thus, ultrafiltration process of this study was suitable for the concentration of fresh aloe gel though the aloe concentrate showed both the viscosity decrease and partially separation of liquid layer during storage at $4^{\circ}C$.

• Journal of KIISE:Information Networking
• /
• v.32 no.1
• /
• pp.60-67
• /
• 2005

A cluster consists of a collection of interconnected stand-alone computers working together and provides a high-availability solution in application area such as web services or information systems. Content-based load distribution for web server clusters uses the detailed data found in the application layer to intelligently route user requests among web servers. In this paper, we propose a content-based load distribution algorithm that considers cache hit and load information of the web servers under the web server clusters. In addition, we expand this algorithm in order to manage user requests for dynamic file. Specially, our algorithm does not keep track of any frequency of access information or try to model the contents of the caches of the web servers.

• Journal of Surface Science and Engineering
• /
• v.24 no.2
• /
• pp.103-113
• /
• 1991

Electroless Ni-Cu-P alloy plating of Al base hard disk was performed to investigate some properties according to the change of composition. It was found that the composition of Ni and Cu in deposits changed linearly with increasing the mole ratio of NiSO4.6H2O/CuSO4.5H2O. The increase in hardness by heat - treatment was confirmed to be associated with small size grained crystallization of the amorphous deposits. Acid resistance of all deposits layer. which had been heated up to 30$0^{\circ}C$, was found to be exellent when immersed in 1N-H2SO4 solution, and it showed more superior acid resistance with decreasing Cu content and with increasing P. The resistivity of the deposits heat treated became smaller at temperature more than 50$0^{\circ}C$, and it became largerly with increasing P content. Cu 44.1wt% alloy(C bath) showed the most superior non-magnetically stable characteristics after heat treatment. It was superiorly with higher temperature and with decreasing P content.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.2
• /
• pp.24-28
• /
• 2018

To understand the effects of Cd substitution for Cu, $(Pb_{0.5}Cu_{0.5-x}Cd_x)Sr_2(Ca_{0.7}Y_{0.3})Cu_2O_z$ (x = 0 ~ 0.5) compounds were synthesized and the structural and superconducting properties of the compounds were characterized. Resistivity data revealed that superconducting transition temperature rises initially up to x = 0.25 and then decreases as the Cd doping content increases. Room-temperature thermoelectric power decreases at first up to x = 0.25 and then increases with higher Cd doping content, indicating that the change in $T_c$ is mainly caused by the change in the hole concentration on the superconducting planes by the Cd doping. The non-monotonic dependence of the lattice parameters and the transition temperature with Cd doping content is discussed in connection with the possible formation of $Pb^{+2}$ ions and the removal of excess oxygen caused by Cd substitution in the charge reservoir layer. A correlation between transition temperature and c/a lattice parameter ratio was observed for the $(Pb_{0.5}Cu_{0.5-x}Cd_x)Sr_2(Ca_{0.7}Y_{0.3})Cu_2O_z$ system.

• Journal of Surface Science and Engineering
• /
• v.26 no.3
• /
• pp.149-157
• /
• 1993

In the study of TAB(Tape Automated Bonding)technologies, Cu-Cr sputtered seed layer has been used to improve the adhesion between Polyimide and Cu film and electrical properties. But the Cu electrodeposit on Cu-Cr film had poor adhesion or powder-like form due to the surface Cr oxides on the Cu-Cr film. By means of activating the Cu-Cr film with the oxalic acid and phosphoric acid, the Cu film with the improved adhesion could be coated on the Cu-Cr sputtered film in CuSO4 solution. The etching rate was compared with increasing the Cr content of the sputtered Cu-Cr film, and anodic polarization curve in FeCl3 solution was investigated. With increasing the Cr content, the etching rate was reduced. The clean etching cross section could be obtained with increasing the concentration of FeCl3 solution. But above the 13 w/o Cr content, Cu-Cr sputtered film could not bed etched cleanly only with FeCl3 solution and additives were needed.

• Corrosion Science and Technology
• /
• v.20 no.4
• /
• pp.196-203
• /
• 2021

To improve corrosion resistance and reduce the hydrogen uptake of 22MnB5, up to 5% Mg was added to the AlSi coating of 22MnB5. After hot-stamping and electrocoating were done on the metallic-coated specimen, the surface characteristics of the steel, hydrogen uptake content, and corrosion resistance were examined by transmittance electron microscopy, thermal desorption spectrometry, cyclic corrosion testing, and electrochemical impedance spectroscopy. Mg was investigated as MgO on the surface layer after hot-stamping while it existed as Mg₂Si before hot-stamping. The total hydrogen content of 22MnB5 was decreased along with the Mg content. However, there was no difference at 0.2 wt% or more. When a small amount of Mg was added, the coating corrosion resistance was decreased, but when it was added at around 1.0 wt%, the greatest corrosion resistance increase was seen. However, when 3 wt% or more was added excessively, the corrosion resistance was decreased. MgO on the surface was considered to suppress H uptake by the AlSi melting solution and increase the barrier effect of the coating.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.1
• /
• pp.45-54
• /
• 1986

A study was conducted to determine the physical properties related to drying characteristics, the seasonal air drying curves and the kiln drying schedule for taun lumber imported and utilized. This kiln drying schedule was found by oven drying and developed by pilot testing of green lumber and partially air dried lumber. The results of this study were as follows; 1. Average green specific gravity and standard deviation of heartwood lumber were 0.60${\pm}$0.03 and those of sapwood lumber were 0.64${\pm}$0.02. 2. Radial shrinkage from green to air dry and from green to oven dry were 3.05 percent and 5.96 percent respectively, and tangential shrinkage from green to air dry and to oven dry were 5.49 percent and 8.74 percent respectively. 3. Drying time for 25mm thick green lumber (50 percent moisture content) air dried to 30 percent moisture content were 14 days in springtime. 6 days in summertime, and 12 days in autumntime, whereas for 50mm thick lumber in 36 days in springtime, 18 days in summertime, 38 days in autumntime. 4. Kiln drying schedules developed by oven drying were T8-B3 for 25mm thick lumber and T5-B2 for 50mm thick lumber. 5. Kiln drying curves of green 25mm and 50mm thick lumber were similar to those of partially air dried lumber from the level of 30 percent average moisture content. Green 25mm thick lumber (55.7 percent moisture content) was dried to 9.3 percent moisture content in 101.5 hours and green 50mm thick lumber (65.6 percent moisture content) was dried to 11.5 percent moisture content in 526 hours. 6. End checking for green 25mm thick lumber occured in 49.6 percent moisture content and reached maximum amount in 27.6 percent moisture content and closed in 15.8 percent moisture content. 7. End checking for green 50mm thick lumber and partially air dried lumber developed and reached maximum amount earlier then for 25mm thick lumber. 8. Final moisture content of surface layer for 50mm thick lumber was one half of that of core, and moisture content equalized in the lumber after nine days of room conditioning. 9. Casehardening for 50mm thick lumber was slight and was conditioned after nine days of room stroage. 10. Drying defects, such as end checking and surface checking, were not observed and the quality of dry lumber was first.

• Applied Biological Chemistry
• /
• v.20 no.1
• /
• pp.147-155
• /
• 1977

In this experiment, we expected yield increase depending on the control of ineffective tiller, heightening of effective tillering ratio and continuous supply of nitrogen until later growth stage of rice plant by deep layer split application. Treats were applied at Tongil and Jinheung variety, clayey loam and sandy loam soil, and drained and non-drained condition. Nitrogenous fertilizer application wab adopted as liquefied(50%) and lumped (50% and 80%) fertilizer at 12cm depth of soil before 35 days of rice heading time against the standard soil surface application. The results are summarized as follaw. 1. a. Jinheung showed great variant width of tiller numbers per rice plant growth stage, and low effective tillering ratio at soil surface dressing. But in the case of deep layer split application, the number of tiller increased normally, and effective tillering ratio was high. b. At Tonsil, the width of increase and decrease range of effective tiller number between soil surface dressing and deep layer split application was not so high as Jinheung. Deep layer split application of 80% lumped fertilizer showed maximum effective tillering ratio ($83%{\sim}93%$). C. In the case of Jinheung, it was supposed that deep layer split application of 80% lumped fertilizer was excessive nitrogen quantity. d. Effective tillering ratio was higher than Tonsil at Jinheung. 2. The number of grains per hill was increased by the deep layer split application, but the ripening ratio was decreased inversely with the increase of total grain number. 3. Length of top leaves was elongated at Jinheung by deep layer split application. It showed significant correlation between top leaves length and grain yield. 4. Deep layer split application inclosed N content of harvested straw. Yield and N content of straw showed possitive correlation. 5. The ratio of unhulled grain yield per straw weight was increased by deep layer splication. This ratio was higher at Jinheung than Tonsil. 6. Grain yield was appeared in order of 80% lumped fertilizer>50% lumped fertilizer>50% liquefied fertilizer>surface dressing by the deep layer split application. The yield increasing factors were the increasing of effective tillering ratio, number of panicles per hill and number of ripening grains per hill. 7. Grain yield was increased at Tongil in sandy loam soil and at Jinheung in clayey loam soil by deep layer split application. 8. The grain yield was increased at drained conditions of clayey loam soil and non-drained conditions of sandy loam soil. But in the case of 80% lumped fertilizer of deep layer split application at the sandy loam soil, the yield was not increased at non-drained conditions. 9. The effect of yield increase by deep layer split application comparing with the surface dressing was higher at Tonsil than ginheung, in spite of low ripening ratio of Tonsil caused by low temperature at heading and harvesting time.

• Economic and Environmental Geology
• /
• v.16 no.2
• /
• pp.65-78
• /
• 1983

This report deals with the sedimentological study of the littoral sand of beaches in the Busan area. The purpose of this report is to know the grain size, mineralogical composition, heavy mineral and clay mineral of the beach sands, and gravity measurements of the Nagdong River Deltas. 1) As a whole, the littoral sand of the beaches are composed of uniformly medium grained, moderately sorted and nearly symmetrical. The barrier sand of the Nagdong Estuary is composed of fine grained, well sorted and nearly symmetrical. 2) The littoral sand of the beaches is transported by saltation and rolling. The barrier sand of the Nagdong Estuary is transported by suspension and saltation. 3) In the littoral sand of the beaches, the ratio of feldspar to quartz is 1 :2.31 and in the barrier sand of the Nagdong Estuary 1:1.40. 4) The content of heavy mineral of samples ranges from 0.54 to 3.87 %. The principal heavy minerals are hornblende, pyroxene, epidote, garnet, leucoxene, zircon, apatite, magnetite, hematite and ilmenite with minor accessories of rutile and olivine. 5) The x-ray diffraction analysis of the clay mineral informs the existence of quartz, feldspar, kaolinite and montmorillonite. The montmorillonite is considered to have been derived from the alteration of acidic volcanic rocks. 6) To determine the depositional structure of the Nagdong Estuary, Gravity measurements were made. Free air anomaly ranges from 14.5 mgal to 33.5 mgal and Bouguer anomaly ranges from 14.3 to 23.5 mgal and both are closely related to the topography. According to the interpreted layer structure, the upper layer composing sand, silt and clay, the intermediate layer composing sand with gravel, the lower layer composing weathered and soft rock, and bed rock composing hornfels or andesite. 7) The depositional environments of the study, the littoral area is dominated by the marine environment and the Nagdong Estuary by the mixed environment.