• Membrane Journal
• /
• v.14 no.2
• /
• pp.166-172
• /
• 2004

As a preliminary study for esterification membrane reactor used to produce 2,2,2-trifluoroethylmetacrylate (TFEMA), Pervaporation behaviors with crosslinked Poly(vinyl alcohol) composite membranes were investigated for aqueous TFEA (2,2,2-trifluoroethanol) feed solutions. In this study, crosslinked PVA composite membranes were prepared by reacting PVA with glutaraldehyde (CA)/acid catalyst onto porous polyethersulfone (PES) supports. SEH images (scanning electron microscopy) showed the thicknesses of selective coating layer was about 2-3 ${\mu}{\textrm}{m}$. The swelling tests showed the dogree of crosslinking decreased as content of the crosslinking agent, GA, increased. Total permeation flux decreased while separation factor increased as the CA content increased. As operating temperature increased, total permeation flux remarkably increased in the range of 85-95 wt% TFEA aqueous solutions. Interestingly, however, separation factor decreased in 85-90 wt% with operating temperature, while that increased in 95 wt%. In case of 90 wt% TFEA concentration and operating temperature 8$0^{\circ}C$, the PVA composite membrane crosslinked with 0.1 mol GA per PVA repeating unit showed high permeation flux of 1.5 kg/$m^2$hr and separation factor of 320. These results confirmed the applicability of the PVA composite membranes for the esterification membrane reactor of TFEMA.

• Geotechnical Engineering
• /
• v.14 no.6
• /
• pp.113-125
• /
• 1998

At the end of 1997 about 3 million tons of coal ash was produced as byproducts from the coal fired electrical power plants in Korea. Only about 27% of that byproducts was utilized as the admixtures of cement and concrete industry. But the large quantity of coal fired fly-ash has been used as the soil improvement materials in other countries. So the aim of this study is the estimation of the applicability of the coal fired fly-ash as microfine grouting materials by admixing the superfine particles which were separated from the coal fired fly-ash for the higher values. The 6 types of specimens were manufactured in the laboratory for the purpose of estimating the chemical and physical properties of cement and grouts. These specimens consisted of 2 specific surfaces of 6, 000 and 8, 000$cm^2$/g in Elaine method. And these specimens are devide into 3 ratios (30%, 50%, 70%) of fly-ash by weight. From the estimated properties of the coal fired fly-ash microflne cements and grouts, 50% fly-ash is the most suitable ratio for grouting materials. However, further study of durability is necessary for using fly-ash grouts practically at the field projects. The higher content of the unburned carbon of fly-ash increases the thinner layer of carbon on the surface of solution of grouts, and requires more quantity of surface active agent. As a results of this study, it is found that the microfine fly-ash is very useful as a good grouting material if 50% of fly-ash is added with the microfine portland cement. So, in the near future, if the coal fired fly-ash is able to be used as grouting material in Korea, the demand of fly-ash will increase rapidly.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.3
• /
• pp.107-116
• /
• 1983

This paper is concerned with the permeability through a decomposed granite soil layer which is influnced by change of grain sizes and crushed soils made by varied compaction energy. The change in the content of crushed soils can be described in terms of the ratio of surface area ($S_w{^{\prime}}/S_w $). The experiments were carried out to obtain the relationships of the coefficient of permeability(K) versus the optimum moisture content($w_{opt}$) by the variable head permeability test with the samples that were preapared by compaction test. The results are found as follows; (1) By the change in compaction energy, the crush ratio increased whereas the void ratio decreased with a larger maximum dry density running in parallel with the zero air void curve. (2) The ratio of surface area was $0.33(P)^{0.96}$ in $S_w{^{\prime}}/S_w $ with no relation to the compaction energy. (3) The grain size which produced the largest crush of soil particles ranged from 0.5 to 1 millimetre (4) The relationship of K versus $e^3$/1+e appeared as a straight line on the full-log-scale paper under the optimum moisture state. (5) As the compaction energy was larger, the passing percentage of #200-sieve grains increased linearly. The increment in the surface area ratio was deemed to have been caused by the decreased in the permeability.

• Korean Journal of Poultry Science
• /
• v.17 no.4
• /
• pp.310-317
• /
• 1990

An experiment was conducted to investigate the effects of adding extra dietary salt on the blood acid－base balance, water intake and egg quality in heat stressed layers. Eighteen 44－wk－old brown commercial layers(Dekalb Warren) were randomly alloted to 0.25 and 0.75% dietary salt treatments, with nine replicates per treatment and one bird per replicate. After 3 d of preliminary period at 13~$16^{\circ}C$(normal temperature), layers were subjected to 3 d of collection period. Then the room temperature was raised to 33－$35^{\circ}C$f(hot temperature), and another 3 d of collodion period was followed. The experiment was designed as a $2\times2$ factorial and analyzed as suck The ANOVA test and comparison among treatment means were done at 5% probability levels. Results obtained were summarized as follows. L The heat stressed layers decreased feed intake, and increased water intake and excreta moisture content significantly. The addition of extradietary salt significantly increased excreta moisture content 2. The heat stressed layers showed significantly higher blood pH and lower $pCO_2$ values than the control bird However, the addition of extra salt did not change any acid－base variables. 3. The egg weight and shell quality decreased significantly, and haugh unit increased significantly by the heat stress. However, these values were not affected by the salt addition. In summary, the heat stressed layers displayed respiratory alkalosis and poor egg quality, as expected However, the addition of ex03 salt to the diet failed to alleviated the heat stress in this layer experiment.

• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.368-373
• /
• 1998

As device dimensions approach submicrometer size in ULSI, the demand for interlayer dielectric materials with very low dielectric constant is increased to solve problems of RC delay caused by increase in parasitic resistance and capacitance in multilevel interconnectins. Fluorinated amorphous carbon in one of the promising materials in ULSI for the interlayer dielectric films with low dielectric constant. However, poor thermal stability and adhesion with Si substrates have inhibited its use. Recently, amorphous hydrogenated carbon (a-C:H) film as a buffer layer between the Si substrate and a-C:F has been introduced because it improves the adhesion with Si substrate. In this study, therfore, a-C:F/a-C:H films were deposited on p-type Si(100) by ECRCVD from $C_2F_6, CH_4$and $H_2$gas source and investigated the effect of forward power and composition on the thickness, chemical bonding state, dielectric constant, surface morphology and roughness of a-C:F films as an interlayer dielectric for ULSI. SEM, FT-IR, XPS, C-V meter and AFM were used for determination of each properties. The dielectric constant in the a-C:F/a-C:H films were found to decrease with increasing fluorine content. However, the dielectric constant increased after furnace annealing in $N_2$atomosphere at $400^{\circ}C$ for 1hour due to decreasing of flurorine content. However, the dielectric constant increased after furnace annealing in $N_2$atmosphere at $400^{\circ}C$ for 1hour due to decreasing of fluorine concentration.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.167-174
• /
• 2001

Reflection method using ultrasonic source has been attempted to obtain the information about tunnel lining structures composed of lining, shotcrete, water barrier and voids at the back of lining. In this work, two different types of sources, i.e. single-pulse source and sweep source, can be used. Single-pulse source with short time duration has the frequency content whose amplitudes tend to be concentrated around the dominant frequency, whereas sweep source with long time duration denotes a flat distribution of relatively larger amplitude over a broad frequency band, although the peak to peak amplitude of single-pulse source wavelet is equivalent to that of sweep source one. In traditional seismic application, a single-pulse source(weight drop, dynamite) is typically used. However, to investigate the fine structure, as it is the case in the tunnel lining structure, the sweep wavelet can be also a desirable source waveform primarily due to the higher energy over a broad frequency band. For the investigation purposes of sweep source, a physical modeling is a useful tool, especially to study problems of wave propagation in the fine layered media. The main purpose of this work was using a physical modeling technique to explore the applicability of sweep source to the delineation of inner layer boundaries. To this end, a two-dimensional physical model analogous to the lining structure was built and a special ultrasonic sweep source was devised. The measurements were carried out in the sweep frequency range 10 ∼ 60 KHz, as peformed in the regular reflection survey(e.g. roll-along technique). The measured data were further rearranged with a proper software (cross-correlation). The resulting seismograms(raw data) showed quitely similar features to those from a single-pulse source, in which high frequency content of reflection events could be considerably emphasized, as expected. The data were further processed by using a regular data processing system "FOCUS" and the results(stack section) were well associated with the known model structure. In this context, it is worthy to note that in view of measuring condition the sweep source would be applied to benefit the penetration of high frequency energy into the media and to enhance the resolution of reflection events.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.4
• /
• pp.559-568
• /
• 2012

White (Lohmann LSL) and Brown (ATAK-S) laying hens, were reared under organic and conventional cage rearing systems, and the effects of the rearing system on performance parameters, egg production, egg characteristics, and immune response were investigated. For this purpose, a total of 832 laying hens of two commercial hybrids, i.e., 416 white (Lohmann LSL) and 416 Brown (ATAK-S) layers, were used. The experiment lasted between 23 and 70 wk of age. In this study, the white layers yielded more eggs as compared to the brown layers in both organic and conventional production systems. Egg weight exhibited a similar pattern to that of laying performance. However, the total hen-housed egg number for the white birds in the organic system was fewer than that of white birds in the conventional cage facility; conversely, a contradictory tendency was observed for the brown birds. Livability of the white layers in the organic system was remarkably lower (14%) than that of the brown line, whereas the white line survived better (3.42%) than their brown counterparts in conventional cages. The feed conversion ratio of the white hens was markedly inferior in the organic system as compared to that of the white hens in the conventional system, whereas relatively lower deterioration was reported in brown layers when reared in an organic system. The organic production system increased egg albumen height and the Haugh unit in eggs of the brown layers. The yolk color score of organic eggs was lower than that of conventional eggs for both brown and white hens. The egg yolk ratio of eggs from white layers was found to be higher in organic eggs as compared to those obtained in the conventional system. All organic eggs had heavier shells than those produced in the conventional system. Eggs from brown layers had more protein content than eggs from white layers. Neither housing systems nor genotype influenced egg yolk cholesterol concentration. When compared to conventional eggs, n-3 fatty acid content was lower in organic eggs, and the n-6:n-3 ratio was higher in organic eggs. In conclusion, two hen genotypes showed different responses in terms of performance and egg quality to two different rearing systems. A commercial white strain produced more eggs with higher egg quality as compared to a native brown strain. The brown strain was found to have adapted well to organic production conditions when survival and total egg number was taken into consideration.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.5
• /
• pp.121-128
• /
• 2010

The present research examined heat insulation performance according to change of various laid construction conditions of double bubble sheet being used as material for heat insulation & curing construction of cold weather concrete, and its results are as follows. First, the change in a laid period of bubble sheet within 4 hours and the change in water content inside bubble sheet overall showed similar temperature history and maturity without a big difference in terms of the temperature history of concrete according to construction factors, but it could be confirmed that when a structure was thin or several bubble sheets are laid, requisites unfavorable for initial curing of concrete can occur if a lagger distance between sheets is generated. In terms of the compressive strength of concrete core specimens, it appeared that the initial compressive strength is declined when conditions unfavorable for concrete curing such as delay of a laid period of bubble sheets, induction of large distance between sheets, increase of water content inside bubble sheets and thinness of a structure of placing concrete, etc. were applied, but it appeared that as its age passes, the difference becomes small.

• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.3
• /
• pp.206-213
• /
• 2008

We observed the physical and chemical properties of a soil on pine mushroom picking areas where were located in the most upper and lower parts showing a comparative climatic characteristics in Korea. The slope gradients within the investigation areas which were divided into 100 quadrates of $1m^2$ ranged from $5.7{\sim}8.6{\beta}$ to $24{\sim}22.7{\beta}$ (left to right) and $4.5{\sim}6.8{\beta}$ to $13.5{\sim}17.8{\beta}$ (top to bottom) for Ponghwa and Gansung, respectively. The amount of clay and thickness of organic matter were significantly decreased with increasing slope gradient, resulting in decrease of the soil moisture content around a fairly ring-colony of Tricholoma matsutake which was observed under the relatively thicker organic matter layer beyond 3 cm depth. Soil pHswere weak acid and average EC was $0.44dS\;m^{-1}$ in both areas. The cations were in the order of Fe K > Na > Mg > Ca and Fe > K > Na > Ca > Mg for the upper(Gansung) and the lower (Ponghwa) part. And the amount of Fe was approximately $80dS\;m^{-1}$ or greater in the pine mushroom picking soil. From this, we could assume that the growth of the pine mushroom was closely related not only with iron but also soil moisture content.

• Membrane Journal
• /
• v.24 no.4
• /
• pp.301-310
• /
• 2014

In this study, the silica nanoparticles were considerably chosen to improve a dimensional stability, proton transport and electrochemical performance of the resulting inorganic-organic nanocomposite membranes. For this purpose, hydrophobic silica (Aerosil$^{(R)}$ 812, Degussa) and hydrophilic silica (Aerosil$^{(R)}$ 380, Degussa) nanoparticles were, respectively, introduced into a Sulfonated poly(arylene ether sulfone) (SPAES) polymer matrix. The $SiO_2$ particles are evenly dispersed in a SPAES matrix by the aid of a non-ionic surfactant (Pluronics$^{(R)}$ L64). A $SiO_2$ content plays an important role in membrane microstructures and membrane properties such as proton conductivity and water uptake. Therefore, to study nanocomposite membranes with excessive amount of silica, the content of silica nanoparticles were increased up to 5 wt%. Interestingly, a hydrophobic $SiO_2$ containing nanocomposite membrane showed better electrochemical performance (29% higher than pristine SPAES) despite of low proton conductivity due to its adhesive properties with a catalyst layer in a single cell test. All the silica-SPAES membranes exhibited better performance than a pristine SPAES membrane.