• Korean Journal of Soil Science and Fertilizer
• /
• v.22 no.3
• /
• pp.191-196
• /
• 1989

Monosaccharide content of four forest soils were analyzed. Two soils under coniferous forest trees and another two under duciduous forest trees of Mts. Zeombong and Odae in Kangweon-Do were sampled from the surface horizon down into the subhorizons. 1. The largest amount of monosaccharide is found in the surface organic horizon of each soil and with increasing depth the amount decreases as might be expected considering total organic matter content. 2. Hexoses (galactose, glucose, mannose) predominate over pentoses (arabinose, ribose, xylose) and deoxyhexoses (fucose, rhamnose), the latter being in the smallest amount. Glucose is the most abundant monosaccharide in all samples regardless of vegetation of soil or depth. In general the content of each monosaccharide follows the order of glucose > manrtose > galactose > arabinose > xylose > rhamnose > fucose > ribose. 3. Very little amount of ribose is present even in organic horizons of coniferous forest soils. In samples taken from deciduous forest soils ribose is virtually absent. 4. The relative proportion of monosacchaiide to the total soil organic matter decreases with increasing depth, which may be resulted from the effect of prolonged humification. The total monosaccharide in the organic surface layer amounts to 27-50% of the total organic carbon or 15.7-29% of the total organic matter. Hexoses alone take the largest share of 20-38% of the carbon, or 12-22% of the organic matter.

• The Journal of Engineering Geology
• /
• v.17 no.1 s.50
• /
• pp.125-133
• /
• 2007

The environmental and geotechnical properties are investigated to the 8th landfill area made of only sewage sludge in Nanji-Do. To do this, the soils are sampled in this area, and leaching tests, heavy metal content tests, and so on are performed to research the environmental properties. As the result of heavy metal content tests, Pb, Zn, Cu, Ni, Cd and Cr were leached from the sewage sludge. Because the leaching concentration of Cu is more than the standard value of California state, Cu content have to bring down during the recycling of the sewage sludge. Meanwhile, a series of tests concerning specific gravity, liquid and plastic limits, compaction, permeability and shear strength is performed to research the geotechnical properties. The sewage sludge is consisted of sand, silt and clay, and is classified into non-organic silt or organic clay with 42.3% of plastic index. As the result of compaction test, it is expected that the compaction effect according to variation of water contents is low relatively because the dry unit weight is low and the curve of compaction forms flatness. Also, as the result of direct shear tests, the cohesion is $0.058kg/cm^2$, and the internal friction angle is $14^{\circ}$. Taking everything into consideration, the various problems are happening in case of recycling the sludge like the cover layer of landfill and so on because the compaction is bad, and the shear strength is low. Also, it is expected that the ground water pollution caused by leaching the heavy metal into the sludge. To do recycling the sewage sludge in this site, supplementary and treatment programs should be prepared.

• Journal of Food Hygiene and Safety
• /
• v.18 no.4
• /
• pp.195-201
• /
• 2003

An easily available, simultaneous identification/determination procedure for sildenafil, homosildenafil, tadalafil, vardenafil in adulterated health related foods was established by using a combination of three different analytical methods; thin layer chromatography(TLC), liquied chromatography-mass spectrometry (LC/MS) and high-performance liquied chromatography (HPLC)/photo-diode-array detector. The sample solution for TLC was applied to silica gel 60 $F_{254}$ plates with ethylacetate/acetonitrile/25%ammonia (90:10:5) as a developing solvent. Spots were located under UV radiation at 254 nm and dragendolfs reagent. Mass spectra of the compounds by LC/MS were investigated with electrospray ionization (ESI) interface, under positive ion mode. The HPLC analysis was performed on a column of capcell pack $C_{18}$ (UG120, 4.6${\times}$250mm I.D. 5 ${\mu}$m)with 0.1% sodium 1-hexansulfonate (in 0.1% phosphoric acid)/acetnitrile (73:27) as a mobile phase, and effluent was minitored with a photo-diode-applied to commercial foods, Sildenafil content was inthe range of 0.4mg/g~360.9 mg/g from 7 out of 35 samples. Homosildenafil content was in the range of 2.2 mg/g~336.0 mg/g from 7 out of 35 samples. Tadalafil content was 429.3 mg/g, 9.6 mg/500 mg from 2 out of 35 samples. The procedure described here is available for the screening of sildenafil, homosildenafil, tadalafil, vardenafil.

• The Korean Journal of Malacology
• /
• v.24 no.3
• /
• pp.243-251
• /
• 2008

Analyses of UV-Vis spectrum and reflectance are useful tools to identify pearls of which color was naturally made or chemically changed. Contents of some trace elements of pearls by using ED-XRF may give us the information that the pearls were originated from marine shells or freshwater shells, and may give us whether the pearls were chemically treated or not. Three types of chemically untreated pearls, freshwater cultured, Akoya cultured and Tahitian cultured, were treated with silver nitrate. UV-Vis absorbance spectrum of Ag was changed after treatment, and reflectance of pearls was decreased. Absorbance of natural black colored Tahitian cultured pearls at 400, 500 and 700 nm was observed. Natural black colored freshwater cultured pearls showed two characteristic absorption patterns in UV-Vis spectra at 380-400, 480-500 nm. Unlike naturally black colored Tahitian cultured pearls, the absorption spectrum at 700 nm could not be found from black freshwater cultured pearls. Manganese was not detected in the pearls from marine shells, and strontium content of the pearls from marine cultured shells was higher than that from freshwater cultured shells. According to ED-XRF analysis, Ag contents of silver nitrate treated pearls increased as more time passed, because silver ion invaded to nacre layer of the pearls. Since Ag content of the black pearls known as untreated ranged under 0.1%, analysis of Ag content may used to distinguish the black pearls are treated or not in marketplace.

• Composites Research
• /
• v.30 no.6
• /
• pp.365-370
• /
• 2017

Mechanical properties of carbon fiber reinforced thermoplastic composites (CFRTPs) are affected by various factors. One of the them are poor compatibility of the epoxy sizing layer on the carbon fiber surface with thermoplastic matrix, which causes the inferior interfacial strength between fibers and matrix. In addition, the high molten-viscosity of thermoplastics attributes to the poor impregnation state. Consequently, many voids in the composite materials were generated, which leads to poor mechanical properties of the thermoplastic composites. In this study, the epoxy sizing on the carbon fiber surface was removed and the polyamide 6,6 solution was coated on the de-sized carbon fiber surface to improve the impregnation state and mechanical properties. Interlaminar shear strength (ILSS) of CFRPTs was estimated by implementing short beam shear tests. In addition, flexural strength was measured and the impregnation state of the composites was evaluated by calculating void content.

• Economic and Environmental Geology
• /
• v.51 no.1
• /
• pp.49-65
• /
• 2018

The lime-soil mixture on tomb barrier (LSMB) is a type of tomb in Joseon Dynasty, which made with so-called 'Sammul' (three material compound) that mixture of lime, fine sand and yellow ocher. This study divided the tombs of the Gungri Site from Joseon Dynasty with layered wall and integrated wall according to the manufacturing types, and investigated on the basis of analysis to material characteristics and making techniques. Analytical samples were classified with lime-soil mixtures and soils, and interpreted the mixing characteristics of Sammul based on types of tomb barrier. The tomb barrier which is directly effect to control the inner environment was made with high content of lime. But the finishing or bottom layer were made with low content of lime. Overall the LSMB with integrated wall has higher content of lime and physical property than the LSMB with layered wall. The soil which was compounded as a Sammul and collected near the Gungri Site had similar with mineralogical and geochemical characteristics. Therefore, it is presumed that the fine sand and yellow ocher that made as a Sammul, were used with soil that was distributed around the site. Meanwhile, large scale limestone quarry is distributed near the site. Especially, Gungri Site has a possibility of material supply through water transport, due to the sea route from Asan bay is connected near the site. Thus, there is the possibility of transportation of lime materials from nearby quarry.

• Journal of Internet Computing and Services
• /
• v.19 no.1
• /
• pp.37-47
• /
• 2018

The number of capabilities of Internet of Things (IoT) devices will exponentially grow over the next years. These devices may generate a vast amount of time-constrained data. In the context of IoT, data management should act as a layer between the objects and devices generating the data and the applications accessing the data for analysis purposes and services. In addition, most of IoT services will be content-centric rather than host centric to increase the data availability and the efficiency of data delivery. IoT will enable all the communication devices to be interconnected and make the data generated by or associated with devices or objects globally accessible. Also, fog computing keeps data and computation close to end users at the edge of network, and thus provides a new breed of applications and services to end users with low latency, high bandwidth, and geographically distributed. In this paper, we propose Edge-Fog cloud-based Hierarchical Data Delivery ($EFcHD^2$) method that effectively and reliably delivers IoT data to associated with IoT applications with ensuring time sensitivity. The proposed $EFcHD^2$ method stands on basis of fully decentralized hybrid of Edge and Fog compute cloud model, Edge-Fog cloud, and uses information-centric networking and bloom filters. In addition, it stores the replica of IoT data or the pre-processed feature data by edge node in the appropriate locations of Edge-Fog cloud considering the characteristic of IoT data: locality, size, time sensitivity and popularity. Then, the performance of $EFcHD^2$ method is evaluated through an analytical model, and is compared to fog server-based and Content-Centric Networking (CCN)-based data delivery methods.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.7
• /
• pp.19-29
• /
• 2013

Analysis via classical soil mechanics theory is either ineffective or inappropriate for fully describing stress distribution or failure conditions in cold regions, since mechanical properties of soils in cold regions are different from those reported in the classical soil mechanics theory. Therefore, collecting and analyzing technical data, and systematic and specialized research for cold regions are required for design and construction of the structure in cold regions. Freezing and thawing repeat in active layer of permafrost region, and a loading condition affecting the structure changes. Therefore, the reliable analysis of mechanical properties of frozen soils according to various conditions is prerequisite for design and construction of the structure in cold regions, since mechanical properties of frozen soils are sensitive to temperature condition, water content, grain size, relative density, and loading rate. In this research, the direct shear apparatus which operates at 30 degrees below zero and large-scaled low temperature chamber are used for evaluating shear strength characteristics of frozen soils. Weathered granite soil is used to analyzed the shear strength characteristics with varying freezing temperature condition, vertical confining pressure, relative density, and water content. This research shows that the shear strength of weathered granite soil is sensitively affected by various conditions such as freezing temperature conditions, normal stresses, relative densities, and water contents.

• Corrosion Science and Technology
• /
• v.8 no.4
• /
• pp.162-169
• /
• 2009

Pure titanium and its alloys are drastically used in implant materials due to their excellent mechanical properties, high corrosion resistance and good biocompatibility. However, the widely used Ti-6Al-4V is found to release toxic ions (Al and V) into the body, leading to undesirable long-term effects. Ti-6Al-4V has much higher elastic modulus than cortical bone. Therefore, titanium alloys with low elastic modulus have been developed as biomaterials to minimize stress shielding. For this reason, Ti-30Ta-xZr alloy systems have been studied in this study. The Ti-30Ta containing Zr(5, 10 and 15 wt%) were 10 times melted to improve chemical homogeneity by using a vacuum furnace and then homogenized for 24 hrs at $1000^{\circ}C$. The specimens were cut and polished for corrosion test and Ti coating and then coated with TiN, respectively, by using DC magnetron sputtering method. The analyses of coated surface were carried out by field emission scanning electron microscope(FE-SEM). The electrochemical characteristics were examined using potentiodynamic (- 1500 mV~+ 2000 mV) and AC impedance spectroscopy(100 kHz~10 mHz) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The equiaxed structure was changed to needle-like structure with increasing Zr content. The surface defects and structures were covered with TiN/Ti coated layer. From the polarization behavior in 0.9% NaCl solution, The corrosion current density of Ti-30Ta-xZr alloys decreased as Zr content increased, whereas, the corrosion potential of Ti-30Ta-xZr alloys increased as Zr content increased. The corrosion resistance of TiN/Ti-coated Ti-30Ta-xZr alloys were higher than that of the TiN-coated Ti-30Ta-xZr alloys. From the AC impedance in 0.9% NaCl solution, polarization resistance($R_p$) value of TiN/Ti coated Ti-30Ta-xZr alloys showed higher than that of TiN-coated Ti-30Ta-xZr alloys.

• Korean Journal of Food Science and Technology
• /
• v.32 no.2
• /
• pp.231-237
• /
• 2000

A Comparative study was performed among five Korean wheat(Greu, Eunpa, Tapdong, Allgreu, Woori) and three imported wheat(Dark Northern Spring, Austrian Standard Wheat, Western White) to investigate the characteristics of minerals and phytate from Korean wheat varieties. Ash contents of kernel was higher in Korean wheat than in imported wheat and related to ash contents and darkness of flour. More contents of Fe, P, and Mg from Korean wheat grains and Fe from Korean wheat flours were observed in comparison to imported wheat varieties. Fe concentration in Korean flour show high, indicating Fe was distributed at endosperm layer of kernels and not eliminated with milling. In addition, phytate affecting availability of minerals was determined from kernels and flours. Even though Korean wheat kernels had more phytate than that of imported wheat kernels, it is believed that most of phytate was removed with milling and there was no major difference between Korean and imported wheat flours. We also observed that the content of phosphate closely parallels the content of phytate from both the flours and kernels.