• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.13-17
• /
• 2006

We investigated the effect of sustain electrode gap variation with high Xe content in an ac Plasma Display Panel through two-dimensional numerical simulation to understand the inherent high luminous efficiency mechanism. For the low Xe content, the optimal sustain electrode gap turned out to be about 200 ${\mu}m$, but with higher Xe content, the VUV generation efficiency increased as the electrode gap increases beyond 200 ${\mu}m$. We found that it is due to higher electron heating efficiency in the cathode sheath under the condition of long electrode gap and high Xe content.

• 공업화학
• /
• 제30권6호
• /
• pp.673-680
• /
• 2019

GAP 및 GAP-co-BO계 에너지 함유 열가소성 탄성체(ETPE)의 하드세그먼트 함량을 30~45% 범위에서 변화시켜 합성하여 열적 특성 및 기계적 특성을 비교 연구하여 고찰하였다. FTIR 분석 결과로부터 GAP-co-BO계 ETPE와 GAP계 ETPE는 하드세그먼트 함량이 증가함에 따라 수소결합을 형성하는 능력이 증가하였으며 GAP-co-BO계 ETPE의 수소 결합 능력이 GAP계 ETPE보다 크게 나타났다. DSC와 DMA 분석 결과로부터 GAP계 ETPE의 유리전이온도(T_g)는 하드세그먼트 함량이 증가함에 따라 증가하였으나, GAP-co-BO계 ETPE의 유리전이온도(T_g)는 하드세그먼트가 증가하여도 유사한 값을 유지하였다. 상온 storage modulus는 GAP-co-BO계 ETPE의 값이 GAP계 ETPE 값보다 더 크게 나타났다. 이러한 거동은 GAP-co-BO계 ETPE 내의 하드세그먼트와 소프트세그먼트의 강한 상분리 거동의 결과로 볼 수 있다. 그 결과 GAP-co-BO계 ETPE는 GAP계 ETPE보다 더 큰 파단강도와 더 낮은 파단신율 값을 나타냈다.

• 대한전기학회논문지
• /
• 제36권11호
• /
• pp.796-805
• /
• 1987

The flashover voltages have been investigated for spacer and unbridged-gap in SF6-N2 gas mixtures up to the value of 760(torr. cm), The gap was stressed by DC source The results obtained are as follows` 1) The flashover voltages for an unbridged gap and for a spacer in SF6, N2 and SF6-N2 gas mixtures follow the Paschen's curve. 2) The polarity effects was not observed in both unbridged gap and a spacer which had per ect contact with an electrode. The flashover voltages for negative polatity are lower than those for positive polarity in case of imperfect contact. 3) 3%flashover voltage is decreased by putting a spacer which had perfect contact with an electrode. The spacer which has a gap void shows the lowest flashover voltage. 4) The lowest spacer efficiency was obtained with higher gas pressure & large amount of N2 content. The flashover voltages depend on the gas pressure rather than the spacer efficienty at low value of pd. 5) The flashover voltages of gas mixtures of N2 with SF6 are relatively high, even though the amount of SF6 gas content is small.

• The Korean Journal of Ecology
• /
• 제18권1호
• /
• pp.179-188
• /
• 1995

Death patterns of gap-makers and changes of environmental factors in gaps formed by disturbance were studied in Pinus densiflora forests of Youngwol, Mt, Mansu, Mt. Songni, Uljin, and Mt, Obong in Korea. Death pattern of gap-makers showed that standing deat type was the most frequent in all the study areas. Longevity of Pinus densiflora was about 140 years, which was about half of that of the temperate deciduous broad-leaved trees. size of gaps were distributed from $20m^2$ to $235m^2$, more than 80% of those were gaps created by death of two or more trees. Relative light intensity and water content of soil in gap area were higher than those in non-gap area and those in the central part of gap were the highest.

• Journal of Ginseng Research
• /
• 제17권2호
• /
• pp.145-147
• /
• 1993

The amounts of ginseng acidic polysaccharide (GAP) in red ginseng (Panax ginseng) were higher than those of wild and cultured Panax quinquefolius, Panax notoginseng as well as white ginseng (Panax ginseng). In white ginseng, there is no difference in the GAP amount among root ages or sizes. Also, the GAP amount of red ginseng body was similar to that of ginseng rhizome, but was higher than that of leaf and epidermis.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.55-58
• /
• 2004

High Xe-content PDP characteristics are discussed. A high efficacy, up to 5 lm/W for a 50% Xe in Ne gas mixture, is realized in 4-inch color PDP test panel designs with low cost stripe-type barrier rib structures, that are powder blasted in soda lime glass. Furthermore, for a high Xe-content a high luminance can be obtained with a relatively small electrode area. Therefore the inter cell gap and the driving margin can be increased in a stripe-type barrier rib structure. Finally, for a high Xe-content the panel lifetime increases, due to increasing luminance and firing voltage stability. Clearly, these findings may direct the design development for next generation PDPs towards a high Xe-content

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4005-4012
• /
• 2022

As high-level radioactive waste (HLW) generated from nuclear power plants is harmful to the human body, it must be safely disposed of by an engineered barrier system consisting of disposal canisters and buffer and backfill materials. A gap exists between the canister and buffer material in a HLW repository and between the buffer material and natural rock-this gap may reduce the water-blocking ability and heat transfer efficiency of the engineered barrier materials. Herein, the basic characteristics and thermal properties of granular bentonite, a candidate gap-filling material, were investigated, and their effects on the temperature change of the buffer material were analyzed numerically. Heat transfer by air conduction and convection in the gap were considered simultaneously. Moreover, by applying the Korean reference disposal system, changes in the properties of the buffer material were derived, and the basic design of the engineered barrier system was presented according to the gap filling material (GFM). The findings showed that a GFM with high initial thermal conductivity must be filled in the space between the buffer material and rock. Moreover, the target dry density of the buffer material varied according to the initial wet density, specific gravity, and water content values of the GFM.

• 한국패션뷰티학회지
• /
• 제2권2호
• /
• pp.93-100
• /
• 2004

This study is to measure the heavy metal content of permanent wave products which on marketing correctly as estimating the extent of exposure by a hair permanent wave scientifically. We would like to prevent an affair from arising health obstruction as to the heavy metal who is using those and also show the basic data for proposing the new standard. The results were as follows.: in case of the average heavy metal content for a wave type thioglycol acid ingredient includes 1.61ppm(Pb), 0.03ppm(Cd), 0.05ppm(Ni), 0.27ppm(Mn), 0.82ppm(Cu) and those were recognized the significant gap between products all the heavy metals. In case of a cysteine acid ingredient includes 0.86ppm(Pb), 0.01ppm(Cd), 0.05ppm(Ni), 0.20ppm(Mn) and 0.66ppm(Cu) and those were recognized the significant gap between products except a nickel. Straight type of permanent wave reductant includes 2.11ppm(Pb), 0.01ppm(Cd), 0.27ppm(Ni), 0.66ppm(Mn), 2.53ppm(Cu) and those were recognized the significant gap between products all the heavy metals. Permanent wave reducing agent includes 1.43ppm(Pb), 0.01ppm(Cd), 0.09ppm(Ni), 0.66ppm(Mn), 0.75ppm(Cu) and those were approved the significant gap between products except a cadmium. Exposure level of the heavy metal contents per onetime permanent waving were 242.3ppm(Pb), 2.5ppm(Cd), 17.7ppm(Ni), 89.0ppm(Mn), 174.7ppm(Cu).

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.199-208
• /
• 2021

3D 프린팅 콘크리트의 출력성능 및 부재 강도는 물시멘트비(Water cement ratio, W/C)와 레이어의 프린팅 시간 간격(Printing Time Gap, PTG)에 의하여 큰 영향을 받을 수 있다. 이 연구에서는 W/C와 PTG를 변수로 하여 제작된 프린팅실험체와 몰드 실험체의 표면수분량과 전단부착강도와의 관계를 측정·고찰하였으며, 그 결과, 레이어표면수분량이 전단부착강도에 큰 영향을 주는 것으로 나타났다. 따라서, 3D 프린팅 출력 시 요구되는 레이어 계면 전단부착성능을 확보하기 위해서는 PTG에 따라 적절한 레이어표면수분량이 유지될 수 있도록 유의해야 하며, 레이어표면수분량에 영향을 줄 수 있는 여러 가지 프린팅 환경인자들 대한 후속 연구도 필요할 것으로 판단된다.

• 한국진공학회지
• /
• 제10권2호
• /
• pp.194-200
• /
• 2001

13.56 MHz rf플라즈마를 이용하여 증착된 DLC(diamond-like carbon) 박막의 광학적 특성에 대해 조사하였다. $CH_4$가스를 원료가스로 하여 PECVD법에 의해 DLC 박막을 형성하였으며 이때 RF power, working pressure, 보조가스의 종류 및 양에 따른 투과도(transmittance)와 optical band gap의 변화를 관찰하였다. RF power가 증가하고 working pressure가 높을수록 optical band gap이 감소하는 결과를 얻을 수 있었고. FT-IR분석을 이용하여 탄소-수소 결합 양을 관찰함으로써 DLC 박막의 결합구조 변화를 증명할 수 있었다. 그리고 수소와 질소를 첨가한 경우 증착시 탄소-수소 결합을 끊는 역할을 하여 optical band gap이 감소하는 결과를 얻을 수 있었다.