• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2006년도 추계학술발표회 초록집
• /
• pp.4-5
• /
• 2006

This paper represents modeling and optimization techniques for solar cell process on single-crystalline float zone (FZ) wafers with high efficiency; There were the four significant processes : i)emitter formation by diffusion, anti-reflection-coating (ARC) with silicon nitride using plasma-enhanced chemical vapor deposition (PECVD); iii)screen-printing for front and back metallization; and iv)contact formation by firing. In order to increase the performance of solar cells, the contact formation process is modeled and optimized. This paper utilizes the design of experiments (DOE) in contact formation to reduce process time, fabrication costs. The experiments were designed by using central composite design which is composed of $2^4$ factorial design augmented by 8 axial points with three center points. After contact formation process, the efficiency of the solar cell is modeled using neural networks. This model is used to analyse the characteristics of the process, and to optimize the process condition using genetic algorithms (GA). Finally, find optimal recipe for solar cell efficiency.

• Tribology and Lubricants
• /
• 제19권3호
• /
• pp.167-177
• /
• 2003

The study deals with the development of a thermohydrodynamic (THD) computational procedure for evaluating the pressure, temperature and velocity distributions in fluid films with very rough geometry. A parametric investigation is performed to predict the bearing behaviors in the lubricating film having the absorbed layers and their interfaces determined by the rough surfaces with Gaussian distribution. The layers are expressed as functions of the standard deviations of each surface to characterize flow patterns between both the rough sur-faces. The velocity variations and the heat generation are assumed to occur in the central (shear) zone with the same bearing length and width. The coupled effect of surface roughness and shear zone dependency on hydrodynamic pressure and temperature has been found in non-contact mode. The procedure confirms the numerically determined relationship between the pressure and film gap on condition that its roughness magnitude is smaller than the fluid film thickness.

• 대한기계학회논문집A
• /
• 제30권11호
• /
• pp.1455-1460
• /
• 2006

The relationship between fatigue crack growth behavior and cyclic crack tip opening displacement is studied. An elastic-plastic finite element analysis (FEA) is performed to examine the growth behavior of fatigue crack, where the contact elements are used in the mesh of the crack tip area. We investigate the relationship between the reversed plastic zone size and the changes of the cyclic crack tip opening displacement along the crack growth. We investigate the effect of the element size when predict fatigue crack opening behavior using the cyclic crack tip opening displacement obtained from FEA. The cyclic crack tip opening displacement is related to fatigue crack opening behavior.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.665-670
• /
• 2001

The purpose of this study is to develop a new type dryer, which is to proceed mixing and drying of wet-materials at the same time and drying process is carried out in a closed system. In this drying system, thermal contact occurs, when a fluidized zone is created by paddle mechanism. Accordingly, wet-materials is dried in a short time without any damage. Also wet-materials could be dried uniformly to low moisture contents. It is suitable to dry a small quantity of multi-kind materials. And drying process is carried out in a closed system, so as for environmental pollution dust not to be emitted into the atmosphere. Accordingly, it could be used to dry not only food and chemical materials, but also environmental pollution materials.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.939-942
• /
• 2008

Moir$\acute{e}$s are a natural interference phenomenon which occurs whenever a transparent regular pattern plate is overlapped on another regular pattern plate. In the contact-type 3 dimensional imaging systems, the moires are inherent because an image display panel is seen through a viewing zone forming optical plate. The mathematical analysis of moires in the systems shows that they can be minimized by the proper selection of overlapping angles between them. The angle is different for pixels with different aspect ratios.

• 상하수도학회지
• /
• 제17권4호
• /
• pp.528-533
• /
• 2003

Bubble size is one of the most important parameters affecting DAF (Dissolved-Air-Flotation) process. It is generally known that small bubbles are preferred. However, the fact seems to be based on the particle removal efficiency at contact zone only, without considering separation zone. Besides, the effect of bubble size on the overall DAF process has not been fully investigated yet. Therefore, the effect of bubble size on collision efficiency, collision chances, and surface loading rate is calculated using theoretical models, and the results are discussed in this paper.

• 콘크리트학회논문집
• /
• 제14권5호
• /
• pp.766-773
• /
• 2002

본 연구에서는 습도 변화와 같은 물리적인 원인으로 보수체의 손상(표면 균열, 경계면 파괴)을 유발하는 표면 인장 응력과 기층과 보수층 단부 경계변의 연직 인장 응력 및 전단 응력이 해석적으로 조사되었다. 응력 계산 시에는 사용 재료의 비선형응력-변형률 곡선이 사용되었고, 특히 변형률 경화, 변형률 연화 특성이 고려되었다. 응력 계산은 보수층의 두께와 보수 재료를 변수로 하였다. 습도 변화에 의한 영향은 보수체가 장기간 공용된 후 수위 하강으로 인해 나타나는 현상(콘크리트 댐)과 보수 후 일정한 양생 기간 후에 거푸집을 제거했을 때 나타나는 현상의 두 가지 경우에 대해서 조사되었다 건조되기 전 보수체 표변의 초기 습도는 100%, 대기 습도는 55%로 가정하였고, 계산기간(양생＋건조기간)은 30일간으로 하였다. 상기 두 가지 경우에 대해서 응력을 계산한 결과, 보수체 표면에서는 일부 보수체(CM20, ECM25)에서 단지 변형률 연화 단계의 가상 균열이 발생되었다. 한편 단부 경계면에서는 양생 중에 부착 강도를 약간 상회하는 일부 보수체(CM20)를 제외하고는 부착 전단 파괴는 발생치 않았다. 습도 변화에서도 단부 경계면의 들뜸현상(Peel-Off)이 보수체 손상의 주요원인으로 나타났고, 이를 유발하는 연직 인장 응력은 공용 중에 건조되는 경우에는 보수층 두께 dO=1cm에서만 부착 강도보다 낮은 값을 유지하고, 보수 작업시 양생 후 대기에 노출되는 경우에는 1.5일 이내에 발현된 부착 강도를 초과하였다.

• 대한소아치과학회지
• /
• 제10권1호
• /
• pp.25-33
• /
• 1983

With electron microscope, author studied on the pulp structure of human primary tooth in shedding stage. Non-carious human primary molar teeth were selected for this study. Using standard methods, specimens were sectioned and examined by light and electron microscope, The results were as follows; 1. In coronal pulp, odontoblasts were replaced by multinucleated odontoclasts, which contained a large number of mitochondria of varying shape and vacuoles in cytoplasm. Where odontoclasts were in contact with tooth surface, the characteristic ruffled border and clear zone were observed. 2. Fibrous tissue with plentiful collagen fibers and fibroblasts was observed adjacent to the dentin in the pulp. Fibroblast contained a number of mitochondria and well-developed rough-surfaced endoplasmic reticulum. 3. Inflammatory cells were observed in the pulp and active fibroblasts could be seen between inflammatory cells. In many cases, cervical epithelium proliferated toward absorbed area. 4. Inflammatory cells consisted of a number of lymphocytes, polymorphonuclear leukocytes, plasma cells and macrophages. Macrophage containing lysosomes in digestive state or phagocyting PMN could be seen. 5. In the primary molar of delayed root resorption, odontoblast layer, zone of Weil and cell-rich zone could be seen at roof of pulp chamber and odontoblast in this area cont과ained some lipid droplets.

• 한국정밀공학회지
• /
• 제26권1호
• /
• pp.97-104
• /
• 2009

There is a many kinds with nondestructive testing such as RT and UT representatively. Referred before two testing methods there is a limit which is spatial such as nuclear pipe, small vessel, sealing up vessel. So a new technique needs to overcome the limit which is spatial. shearography will be able to overcome the limit which is spatial. This paper introducing shearography which was known as non-contact full-field testing method and It is an interferometric technique for measurement of surface deformation such as displacement or displacement gradient. Also, a research about internal defect of the flange welding zone was accomplished. About variation with method pressurized with the Gaseous Nitrogen. Phase map where is various were measured according to changing a sheared direction, size of crack and loaded pressure. Consequently, crack quantitatively to be detected qualitatively was measured by using shearography.

• 한국생산제조학회지
• /
• 제8권6호
• /
• pp.84-91
• /
• 1999

The goal of this study is to analyse the stress and the strain occurring within the work piece at the fine-blanking process and hence to assume the size direction and a distribution chart of the shearing stress as the penetration of the punch is being increased trough the application of the FEM. For this analysis we introduced the piece-wise linear method in the non linear structural analysis program for large deformation sheet metal forming and we defined it as the problem of the non linear contact. Therefore we modeled the above problems as quadratic-nodded axi-symmetrical elements for the character-istics of the work piece. From the result of this analysis it was found that the shearing stress is a great deal occurred on the surface of the work piece during the beginning process of the punch penetration and it's effect is expected to influence importantly for the formation of burnish because the deeper is the penetration of the punch in the narrow clearance zone. the greater is the degree of the strain stress.