• 한국안광학회지
• /
• 제18권1호
• /
• pp.19-25
• /
• 2013

목적: 일상생활에서의 조도 환경에 따라 써클 소프트콘택트렌즈의 착색부분에 의한 콘택트렌즈 착용자의 동공 가 려짐 정도를 확인하고 동공의 가려짐에 따른 시력 변화를 알아보고자 하였다. 방법: 20대 82안을 대상으로 비착색 부위가 렌즈 중심부 6.2 mm 직경인 써클 콘택트렌즈를 착용시키고 50 lx 및 370 lx의 조도에서 최소분리시력 및 최소가독시력을 측정하였다. 결과: 370 lx에서는 써클 콘택트렌즈 착용 시 착색부위에 의한 동공의 가려짐이 없었으나, 50 lx에서는 모든 실험대상안의 동공이 써클 콘택트렌즈에 의한 가려짐이 나타났으며 그 범위는 0.40~1.70 mm이었다. 50 lx에서는 써클 콘택트렌즈의 착용에 의해 최소가독시력 및 최소분리시력이 통계적으로 유의하게 감소하였으며, 동공 크기가 큰 실험대상안 일수록 시력의 감소 정도가 더 커지는 상관관계를 가짐을 확인할 수 있었다. 또한, 최소분리시력의 감소 정도가 최소가독시력의 경우보다 더 크게 나타나 동공의 가려짐에 의해 최소분리시력이 더 크게 영향을 받는 것을 알 수 있었다. 결론: 조도가 낮은 실내에서나 야간 활동 시의 써클 콘택트렌즈 착용은 시력에 직접적으로 영향을 끼칠 수 있으므로 이에 대한 착용자 및 제조사의 고려가 필요하다.

• 한국진공학회지
• /
• 제19권1호
• /
• pp.22-27
• /
• 2010

$TiO_2$의 표면의 친수성을 증가시키기 위하여 dielectric barrier discharge (DBD)에 의해 발생된 대기압 플라즈마 (atmospheric pressure plasma: APP)를 이용 RF power 50~200 W 범위에서 Ar과 $O_2$ 가스를 사용 대기압 플라즈마로 광촉매 표면을 개질하였다. Ar 가스 단독으로 처리한 시료의 접촉각은 20도에서 10도로 감소하였으며, $O_2$ 가스를 반응성 가스로 하여 처리한 경우에는 접촉각이 20도에서 1도 미만으로 감소하였다. 동일한 RF power에서 $O_2$ 플라즈마 처리 시 더 낮은 접촉각을 확인하였는데, 이는 $TiO_2$ 표면과 산소원자의 결합으로 인하여 표면의 polar force의 증가에 의한 것으로 판단되어 대기압 플라즈마로 처리된 시료의 X-ray photoelectron spectroscopy (XPS)의 스펙트럼 분석결과 OH 작용기의 증가로 표면의 친수성이 증가됨을 확인하였다. 대기압 플라즈마로 처리된 시료와 처리하지 않은 시료의 접촉각은 모두 시간이 지남에 따라 증가하지만 플라즈마 처리 된 시료의 접촉각 증가는 플라즈마 처리하지 않은 시료의 접촉각 보다 작은 것을 확인하였다. 또한, 페놀 분해 실험을 통하여 플라즈마 표면처리를 통하여 $TiO_2$ 광촉매의 분해 효율이 크게 향상되는 것을 확인하였다.

• Macromolecular Research
• /
• 제8권1호
• /
• pp.6-11
• /
• 2000

In this study, we examined the charging behavior of chopped carbon fibers during electro-flocking process, which is one of the key processes of the novel technique for fabricating conductive polymer composite films. Short carbon fibers (CF) during electroflocking were electrically charged by the combined effect of contact charging, corona charging and tribocharging. The specific charge built on CF surface was measured by using Faraday cup method. Specific charge increased not only with increasing electric field strength and potential impressed to mesh electrode as expected from theoretical considerations in literature, but with decreasing mesh opening size due to the improved contact charging condition. However, CF length was found unexpectedly to influence the amount of CF specific charge due to the agglomerated nature of CF flocks leading to the change in charging conditions.

• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1645-1652
• /
• 2002

The failure analysis on fractured parts is divided into the qualitative method by naked eyes and metallurgical microscope etc. and the quantitative method by SEM and X-ray diffraction etc. X-ray fractography can be applied to contaminated surface as well as clean surface and gain the plastic deformation and the residual stress near the fractured surface. Turbine blade is subject to cyclic bending force by steam pressure and suffers fatigue damage according to the increasing operating time. Therefore, to clean up the fracture mechanism of torsion-mounted blade in nuclear plant, the fatigue and the X-ray diffraction test was performed on the 12%Cr steel fur turbine blade and the fractured parts. The correlation of X-ray parameter and fracture mechanics parameter was determined, and then the load applied to actual broken turbine blade was predicted. Failure analysis was performed by contact stress analysis and Goodman diagram of torsion-mounted blade.

• Journal of the Korean Wood Science and Technology
• /
• 제10권3호
• /
• pp.190-193
• /
• 1982

Conclusion: The results of this study are encouraging for the development of a set of interpretable diagnostic criteria for a reasonably reliable identification of some species. The present study has been limited in the characteristics studied and was made on relatively poor photography. Further study on high quality photography, over wider areas and including such additional characteristics as crown texture and shadow intensity should prove useful. A preliminary examination has been made of some photo-image characteristics of a number of important tree species on large scale (1:9,000) contact prints of panchromatic mm. The characteristics studied were crown image tone, and shape. Image tone was estimated against a standard grey-scale and shows within-species consistency and a range between species. Crown shapes were subjectively assessed but there appears to be a within-species consistency and interpretable between-species differences. The results of this trial suggest that it should be practicable to make a number of important species distinctions by photo-interpretation with a useful degree of reliability. Other characteristics beside those studied might be usefully examined. Photography: Hand-printed glossy contact prints of vertical 1:9,000 scale panchromatic photography of Kwangnung Experimental Forest flown May 1964. The filter used is unknown (probably minus-blue). The camera is unknown but was probably a military type K-17 or K-22 with 6"(apostfophy) lens. The photography shows notably poor resolution. Species: 143 individual trees ranging through 11 species (7 softwood, 4 hardwood) were included in the study. A range of size classes were included for each species.

• 한국전기전자재료학회논문지
• /
• 제21권7호
• /
• pp.610-614
• /
• 2008

In this work, the electrical and optical properties of the two different p-type GaN electrode schemes, ZnNi/ITO and ZnNi/Au, were compared each other, and applied to the top-emitting GaN/InGaN light-emitting diodes (LEDs). The ZnNi/ITO electrode showed much higher transmittance (90%) and slightly lower contact resistance $(1.27{\times}10^{-4}{\Omega}cm^2)$ than those (77%, $(2.26{\times}10^{-4}{\Omega}cm^2)$) of the ZnNi/Au at a wavelength of 460 nm. In addition, GaN LEDs having ZnNi/ITO showed accordingly higher light output power and luminous intensity than those having ZnNI/Au did at the current levels up to 1 A.

• 대한기계학회논문집A
• /
• 제24권6호
• /
• pp.1565-1574
• /
• 2000

Surface edge crack subjected to contact stresses is analysed. A punch with corner radii is considered to press the semi-infinite plane. Partial slip problem is solved when a shear force is applied to the punch. Dislocation density function method is used to solve the present mixed mode crack problem. The crack length of positive K1 is examined, which is affected by the ratio of the flat portion to the total width of the punch. Surface traction during one cycle of the shear force is evaluated to simulate the fretting condition. The compliance change of the contact surface is also investigated during the shear cycle. It is found that the crack grows during only a part of the cycle, which may be termed as effective period of crack growing. A design method for restraining the fretting failure is discussed, from which recommendable geometry of the punch is suggested.

• 한국재료학회지
• /
• 제5권1호
• /
• pp.63-74
• /
• 1995

클러스터형의 다중 공정용 장치에 부착키 위해 제작된 콘택 산화막 식각용 공정모듈에 대한 적정 식각 공정조건을 확립하기 위해, Taguchi 방법을 활용하여 공정최적화 실험을 수행하였다. Taguchi 실험은 2회에 걸쳐 시행되었는데, 제1차 실험은 장비변수에 대한 식각공정변수의 개괄적 거동을 타진하기 위함이었고, 제2차 실험은 상세 공정조건 확립을 위해서였다. 실험 및 분석 결과 $CHF_{3}/CF_{4}$ 가스유량은 72/8sccm, 공정압력은 50 mTorr, RF 전력은 500 Watts, 자계강도는 90 Gauss일때 최적 공정 성능을 발휘함을 알 수 있다.

• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1254-1260
• /
• 2000

There have been many developments in super precision working technique and working method up to, now. But, it is very difficult to evaluate working surface accurately without the technicians experience and judgment. Surface roughness tester using stylus was used to measure surface condition generally But this method is not so desirable because of damage on test piece caused by contact between the workpiece and the stylus sensor. As a result, non-contact method was known as a good way to carry, out this process without damage. However, this is a difficult one among the various measuring methods. So we are tying to suggest a new method using texture analysis through image processing to get a surface information in worked test piece. Co-occurrence matrix using difference of gray levels between a pixel and its neighboring one was used to study behavior of surface roughness and to J acquire data for analysis. Standard specimen was adapted to verify this research. We suggest texture information method in order to evaluate surface state for the best measurement system.

• 한국산학기술학회논문지
• /
• 제14권11호
• /
• pp.5366-5370
• /
• 2013

본 연구에서는 볼트의 원활한 성형이 이루어지도록 볼트의 성형 공정 중 2단계에서 시행하던 압출공정을 4단계로 옮기고 2단계와 3단계에서는 볼트 머리부 성형만 이루어지도록 공정을 조정하여 해석하였다. 그 결과 약간의 수정으로 원활한 성형이 이루어 졌으며 접촉압력은 수정 전보다 1단계에서는 감소하고 2단계에서는 증가하였으며, 최대유효응력, 유효변형율, 성형력은 수정전보다 1, 2단계에서 모두 증가함을 알 수 있었다.