• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 추계학술대회 논문
• /
• pp.180-186
• /
• 1996

Using carbon steel or ceramic as a shaft material of monolithic and slited insert ring clamped on it. The fitting strengths of the sgrink fitted assemblies measured from room temperature to 30$0^{\circ}C$ and following conclusions were obtained as results of this investigation. 1) The fitting condition under which the shrink fitted assemble was stronger than that using simple fit in high temperature. 2) When both material of the 30mm-diameter shaft and 55mm-diameter boss are SM45C the clamping torque is increased 2.7times as the interference increases 3 times from 20${\mu}{\textrm}{m}$ at the contact length of 6mm monolithic fit. 3) When only the material of boss is changed to STS 304 the clamping torque is increased at the rate of 37.3N.m per 1mm increase of the contact length at the interference of 50${\mu}{\textrm}{m}$ monolithic fit.

• 반도체디스플레이기술학회지
• /
• 제6권1호
• /
• pp.59-64
• /
• 2007

Non-contact transportation of a large-sized glass plate using air cushion for the vertical sputtering system of liquid crystal display (LCD) panel was considered. The objective of the study was to design an air pad unit which was composed of multiple injection and exhaust holes and mass flow supplying pipe. The gas was injected through multiple small holes to maintain the force for levitating glass plate. After hitting the plate, the air was vented through exhaust holes. Complex flow field and resulting pressure distribution on the glass surface were numerically studied to design the air injection pad. The exhaust hole size was varied to obtain evenly distributed pressure distribution at fixed diameter of the injection hole. Considering the force for levitating glass plate, the diameter of the exhaust hole of 30 to 40 times of the gas injection hole was recommended.

• 소성∙가공
• /
• 제18권1호
• /
• pp.80-86
• /
• 2009

This paper presents the plastic inhomogeneous deformation behavior of bimetal composite rods during the axisymmetric and steady-state extrusion process through a conical die. The rigid-plastic FE model considering frictional contact problem was used to analyze the co-extrusion process with material combinations of Cu/Al. Different cases of initial geometry shape for composite material were simulated under different conditions of co-extrusion process, which includes the interference and frictional conditions. From the simulation results, the sleeve cladding rate at the core/sleeve interface was recorded as a distribution of diameter ratio and interference conditions, which will be useful for the investigations of the bonding process during co-extrusion process. In addition, the results of the co-extrusion, connected with the results of the variations of diameter rate and average contact pressure, demonstrate a good agreement and present the possibility of describing the parameters of the plastic zones in non-uniform deformation of these type of composite materials.

• 오토저널
• /
• 제9권5호
• /
• pp.57-65
• /
• 1987

The surface rolling method which is one of the plastic deformation processes increases the surface roughness with reduction of diameter and hardness. In this study, three NACHI 6000 ZZ bearing were used for surface rolling tool on a mild steel The following results have been obtained with the mild steel. 1) The load is major factor in getting fine surface roughness of roller finishing after grinding The optimal surface roughness of SS41 steel can be obtained at the contact pressure of 210 kgf/cm$^{2}$. 2) At the contact pressure range of 200kgf/cm$^{2}$-210kgf/cm$^{2}$ for optimal surface roughness, The surface hardness increased to Hv200-Hv240 from Hv 125 before surface rolling. 3) Within the diameter variation of 13 .mu.m the surface roughness and the surface hardness were increased, but out of variation of 14.mu.m. The surface roughness become worse and the surface hardness was increased.

• 한국안전학회지
• /
• 제2권1호
• /
• pp.31-41
• /
• 1987

The surface rolling method which is one of the plastic deformation processes increases the surface roughness with reduction of diameter and hardness. In this study, three NACHI 6000 ZZ bearing were used for surface rolling tool on a mild steel. The following results have been obtained with the mild steel. 1) The load is major factor in getting fine surface roughness of roller fininshing after grinding. The optimal surface roughness of SS40 steel can be obtained at the contact pressure of $210kgf/cm^2$. But, Better surface roughness can not be expected, Due to flaking phenomena at more than 300 kgf/cm of contact pressure. 2) At the contact pressure range of $200kgf/cm^2{\sim}210kgf/cm^2$ for optimal surface roughness, The surface hardness increased to Hv 200~Hv 240 from Hv 125 before surface rolling. 3) Within the diameter variation of $13{\mu}m$ the surface roughness and the surface hardness were increased, but out of variation of $14{\mu}m$. The surface roughness become worse and the surface hardness was increased.

• 대한치과보철학회지
• /
• 제30권2호
• /
• pp.233-245
• /
• 1992

The purpose of this study was to evaluate the demensioal stability and wettability of several rubber impression materials. Impressions were made from a metal master die machined to stimulate five full veneer crown preparations symmetrically placed in an arch form. Cast from impressions were measured about ; 1) intrapreparation distance 2) lower base diameter 3) length. For comparing materials were formed against a smooth surface. The advancing contact angle of a saturated aqueous solution of $CaSO_4$ on the impression materials was measured after 1 minute. Mean contact angle were calculated and results were analyzed. Results were as follows : 1. As the intrapreparation distance, hydrophilic addition-cured silicone had the smallest change and condensation-cured silicone had the largest one. 2. As the lower base diameter, traditional addition-cured silicone had the smallest change and polyether had the largest one. 3. As the height, traditional addition-cured silicone had the smallest change and polyether had the largest one. 4. As the contact angle, polyether had the smallest change and condensation-cured silicone had the largest one.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.402-402
• /
• 2011

본 연구에서는 결정질 태양전지 제작에 있어 재료비 절감과 기존의 Screen Printing 공정 기술에서의 단점을 보완하기 위한 방안으로 후면 passivation 구조와 레이저를 이용한 국부적 후면 전극 형성(Laser Fired Contact) 방법에 대한 실험을 진행하였다. 후면 passivation 층으로 SiO2/ SiNx/SiO2 삼중막 구조와 SiNx 단일막 구조를 형성시킨 후 anneal 온도에 따른 소수캐리어의 lifetime 변화를 비교하였다. LFC 형성은 2 ${\mu}m$ 두께의 Al이 증착된 기판 후면에 1,064 nm 파장의 레이저를 통해 diameter와 dot pitch 등의 파라미터를 가변 하여 실시하였다. 실험 결과 800$^{\circ}C$의 고온 열처리 후 ONO 삼중막에서의 lifetime 향상이 우세하여 SiNx 단일 막 보다 열적 안정성이 우수함을 확인하였다. LFC 결과 diameter가 40, 50, 60 ${\mu}m$로 가변된 조건에서는 40 ${\mu}m$ 일 경우와 dot pitch가 200, 500, 1,000 ${\mu}m$로 가변된 조건에서는 1,000 ${\mu}m$일 경우 610 mV의 Voc 값을 보였다. 이는 레이저를 통해 국부적으로 Al-Si 간 alloy를 형성시킴으로써 접촉 면적이 최소화됨에 따라 후면에서의 캐리어의 재결합속도를 감소시키고, passivation 효과를 극대화시키기 때문이다.

• 한국자동차공학회논문집
• /
• 제13권1호
• /
• pp.45-50
• /
• 2005

Stick type ignition coil(called a Cigar coil) is a kind of transformer for an automobile modulaized of distributer and electric cable. A material of cigar coil is PBT $GF30\%$ resin. This is an excellent engineering plastic with both mechanical and electrical properties. When we insert an HV terminal into the PBT $GF30\%$ resin jacket, it breaks the jacket, because the HV terminal is bigger than the jacket. It is a fatal on durability of a part. In this study, We used ANSYS FEM tool in order to stress analysis by contact. In order to automatically estimate possible maximum diameter of an HV terminal, we used an APDL. In the contact part, we considered the relation of the HV terminal's diameter with the amount of stress that occurred. This relation is able to be applied, in part, to the dimensions of the part design.

• Nuclear Engineering and Technology
• /
• 제29권1호
• /
• pp.45-57
• /
• 1997

The direct contact condensation phenomenon, which occurs when steam is injected into the subcooled water, has been experimentally investigated. Two plume shapes in the stable condensation regime are found to be conical and ellipsoidal shapes depending on the steam mass flux and the liquid subcooling. Divergent plumes, however, are found when the subcooling is relatively small. The measured expansion ratio of the maximum plume diameter to the injector inner diameter ranges from 1.0 to 2.3. By means of fitting a large amount of measured data, an empirical correlation is obtained to predict the steam plume length as a function of a dimensionless steam mass flux and a driving potential for the condensation process. The average heat transfer coefficient of direct contact condensation has been found to be in the range 1.0~3.5 ㎿/$m^2$.$^{\circ}C$. Present results show that the magnitude of the average condensation heat transfer coefficient depends mainly on the steam mass fin By using dynamic pressure measurements and visual observations, six regimes of direct contact condensation have been identified on a condensation regime map, which are chugging, transition region from chugging to condensation oscillation, condensation oscillation, bubbling condensation oscillation, stable condensation, and interfacial oscillation condensation. The regime boundaries are quite clearly distinguishable except the boundaries of bubbling condensation oscillation and interfacial oscillation condensation.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.310-317
• /
• 2013

In this paper, the contact pressure of the wafer and polishing pad for final polishing process for 300 mm-wafer were investigated through numerical analysis using FEM tool, ANSYS. The distribution of the contact pressure is one of main parameters which affects on the flatness and surface roughness of polished wafers. Two types of polishing head, a hard type head with ceramic disk and a soft type head with air bag were considered. The effects of the deformation and initial shape of table on the contact pressure were also examined. Both heads and tables were modeled as 3D finite element model from solid model, and the material properties of polishing pads and rubber plate for the air-bag head were obtained from tensile tests. The contact pressure deviation on wafer surface was smaller with air bag head than hard type head even when the table had form errors such as convex or concave. From this 3D analysis, it could be concluded that the air-bag head has better uniformity of the contact pressure on wafer. Also, the effects of inner diameter of air bag and radial clearance between wafer and retainer were investigated as view point of contact pressure concentration on the edge of wafer.