• 마이크로전자및패키징학회지
• /
• 제6권1호
• /
• pp.39-49
• /
• 1999

Monolayer 두께의 불화된 유기박막의 특성을 접촉각 측정을 통해 분석 하였다. 정접촉각을 표면장력의 다른 세 가지의 극성(water, formamide), 비극성(diiodomethane) 용액을 이용하여 Teflon, Spin coating된 FC막, 기상증착된 PFDA와 FC막위에 측정하였다. Aluminum위에 증착된 불화 유기박막이 물에 대해 $130^{\circ}$가 넘는 가장 큰 정접촉각을 나타내었다. 반면에 산화막위에 증착된 유기박막은 $70^{\circ}$미만의 낮은 접촉각을 갖었다. Teflon은 $108^{\circ}$, Spin coating된 막은 $121^{\circ}$로 측정되었다. 이들 측정된 값을 이용 Lewis acid/base 이론에 적용 박막의 표면에너지를 계산한 결과 Teflon의 경우는 18 dynes/cm, Spin coating된 유기박막은 8.4 dynes /cm의 낮은 에너지 값이 계산되었다. 실리콘과 산화막위에 증착된 유기박막은 상대적으로 높은 31~35 dynes /cm의 값을 나타내었으나 aluminum위에 증착된 막에서는 Lewis base 항이 큰 음수 값을 갖는 이례적인 경우가 발생하였다. 이때 음수값을 무시한 경우 계산된 aluminum 상의 증착된 유기박막의 표면에너지 PFDA가 13dynes / cm 이였다. 이는 동접촉각과 AFM 측정결과 다른 표면과는 다르게 aluminum강의 유기박막의 비균질성과 표면의 높은 거칠기에 기인함을 알 수 있었다.

• The Journal of Advanced Prosthodontics
• /
• 제1권1호
• /
• pp.1-5
• /
• 2009

STATEMENT OF PROBLEM. Poor wettability of denture relining materials may lead to retention problems and patient discomfort. PURPOSE. Purpose of this study is to compare and evaluate wettability of nine denture relining materials using contact angle measurements under air and water storage over time. MATERIAL AND METHODS. Nine denture relining materials were investigated in this study. Two heat-curing polymethyl-methacrylate(PMMA) denture base materials: Vertex RS, Lang, one self-curing polyethyl-methacrylate(PEMA) chairside reline resin: Rebase II, six silicone relining materials: Mucopren soft, Mucosoft, $Mollosil^{{R}}$ plus, Sofreliner Touch, GC $Reline^{TM}$ Ultrasoft, Silagum automix comfort were used in this experiment. Contact angles were measured using high-resolution drop shape analysis system(DSA 10-MK2, KRUESS, Germany) under three conditions(in air after setting, 1 hour water storage, and 24 hours water storage). Nine materials were classified into three groups according to material composition(Group 1: PMMA, Group 2: PEMA, Group 3: Silicone). Mean values of contact angles were compared using independent samples t-test and one-way ANOVA, followed by a Scheffe's post hoc analysis($\alpha$=0.01). RESULTS. Contact angles of materials tested after air and water storage increased in the following order: Group 1(PMMA), Group 2(PEMA), Group 3(Silicone). Heat-cured acrylic denture base resins had more wettability than silicone relining materials. Lang had the highest wettability after 24 hours of water storage. Silicone relining materials had lower wettability due to their hydrophobicity. Wettability of all denture relining materials, except Rebase II and $Mollosil^{{R}}$ plus, increased after 24 hours of water storage. CONCLUSIONS. Conventional heat-cured resin showed the highest wettability, therefore, it can be suggested that heat-cured acrylic resin is material of choice for denture relining materials.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.22-27
• /
• 1993

The finite element method is applied to analyze the mechanism of metal cutting. This paper introduces some effects, such constitutive deformation laws of workpiece material, friction of tool-chip contact interfaces, tool rake angles and also simulate the cutting process, chip formation and geometry, tool-chip contact, reaction force of tool, cutting temperature. Under the usual [lane strain assumption, quasi-static analysis were performed with variation of tool-chip interface friction coefficients and rake angles. In this analysis, various cutting speeds and depth of cut are adopted. Some cutting parameters are affected to cutting force, plastic deformation of chip, shear plane angle, chip thickness and tool-chip contact length and reaction forces on tool. Cutting temperature and Thermal behavior. Several aspects of the metal cutting process predicted by the finite element analysis provide information about tool shape design and optimal cutting conditions.

• 대한기계학회논문집A
• /
• 제32권2호
• /
• pp.143-147
• /
• 2008

Super-hydrophobic surfaces showed that contact angle of water was higher than 140 degrees. That surface could be made several methods such as Carbon nano tubes grown vertically, PDMS asperities arrays, hydrophobic fractal surfaces, and self assembled monolayers coated by CVD and so on. However, we fabricated super-hydrophobic surfaces with plasma treatments which were very cost efficient processes. Their surfaces were characterized by static contact angles, advancing, receding, and stability against UV irradiation. Optimal surfaces showed static contact angles were higher than 150 degrees. Super-hydrophobic property was remained after UV irradiation for one week.

• 대한기계학회논문집A
• /
• 제20권1호
• /
• pp.180-188
• /
• 1996

The stress singularity of a sharp wedge contacting a half plane can be avoided by changing the wedge shape. Shape optimization is accomplished with the geometric strain method (GSM), an optimality criterion method. Several numerical examples are provided for different materials in the wedge and half plane to avoid stress singularity neal the sharp corner of the wedge. Optimum wedge shapes are obtained and critical corner angles are compared with the angles from analytical contact mechanics. Numerical results are well matched to analytical and experimental results. It is shown that shape optimization by the geometric strain method is a useful tool to reshape the wedge and to avoid a stress singulatiry. The method applies to more general geometries where the singular behavior would be difficult to avoid by classical means.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.256-256
• /
• 2011

Using plasmas, hydrophobic surfaces are made on various substances such as polyimide films, filter paper, cotton clothes and multi-walled carbon nanotube (MWCNT) with hexamethyldisiloxane (HMDSO), trimethylchlorosilane (TMCS) and toluene reagents. Plasmas are easily and rapidly to change surface of hydrophilic materials into hydrophobic. We have also optimized processing time and maximized contact angle for super-hydrophobicity of MWCNT. Contact angles have been calculated by measuring between substance and probe liquid, and total surface free energies are determined by the Owens-Wendt equation. Figure 1 shows the measured contact angles with time and ratio of reagents on MWCNT.

• 한국세라믹학회지
• /
• 제20권3호
• /
• pp.199-204
• /
• 1983

An attempt was made to study wetting behavior of various low temperature molten frist on ceramic substrates including high alumina silicon carbide and porous fired clay plates by Sessile-drop method. The cosine values of contact angles between substrates and molten frist were linear as a function of temperature unless chemical reactions between substrate and molten frit occured. Addition of BaO to frit composition indicated that cosine of values of contact angles were gradually increased with increasing temperature but in the frist contained $Li_2O$ consine values were abruptly increased with increasing temperature after reached a certain temperature. The contact angle increased with increasing roughness of the substrate surface in case of alumina substrate plate.

• Journal of Welding and Joining
• /
• 제16권2호
• /
• pp.122-128
• /
• 1998

This investigation was performed to collect fundamental informations concerning the behavior of glass solders on ceramic joining process. The wettability of glasses on two types of alumina was evaluated by sessile drop method. SiO$_2$-CaO-Al$_2$O$_3$system glasses were selected as solder glasses, and alumina that have different purities were used for substrate materials. It is indicated that contact angles of glasses on 99% purity of alumina substrate do not change as increasing time at elevated temperature, however the contact angles on the 92% purity of alumina substrate exhibit the strong time dependency. The time-dependent property on 92% alumina was due to the interlayer reactions occurred between the glass solder and impurities on the substrate.

• 한국분무공학회지
• /
• 제17권1호
• /
• pp.9-13
• /
• 2012

This study investigates experimentally evaporation characteristics of nanofluid droplets containing 50 nm alumina($Al_2O_3$) particles and the wettability changes on a hydrophilic glass surfaces. From the captured digital images by using a CMOS camera and a magnifying lens, we examined the effect of particle concentration on droplet evaporation rate which can be indirectly deduced from the measured droplet volumes varying with time. In particular, with the use of a digital image analysis technique, the present study measured droplet perimeters and the contact angles to study the wetting dynamics during evaporating process. In addition, we compared the measured total evaporation time with theoretically estimated values. It was found that as the volume fractions of nanofluid increased, the total evaporation time and the initial contact angles decreased, while the droplet perimeters increased.

• 센서학회지
• /
• 제17권5호
• /
• pp.375-379
• /
• 2008

This paper reports a new fabrication method of polydimethylsiloxane (PDMS) microlenses with various curvatures by using a water-based mold. The hydrophobic surface of Polypropylene (PP) substrate was modified by corona discharge using tesla coil to have hydrophilic surface. Then hydrophilic surface of PP substrate takes hydrophobic recovery to have various contact angles from less than $25^{\circ}$ to about $84^{\circ}$. By using the water droplets with various contact angles as replica molds for PDMS process, we could obtain PDMS microlenses with various curvatures.