• 대한조선학회논문집
• /
• 제42권5호
• /
• pp.479-486
• /
• 2005

The final goal of shift alignment design is that the bearing reaction forces or mean pressures are within design boundaries for various service conditions of a ship. However, it is found that calculated bearing load can be substantially variable according to the locations of the effective support points of after sterntube bearing which are determined by simple calculation or assumption suggested by classification societies. A new analysis method for shaft alignment calculation is introduced in order to resolve these problems. Key concept of the new method is featured by adopting both nonlinear elastic and multi-support elements to simulate a bearing support Hertz contact theory is basically applied for nonlinear elastic stiffness calculation instead of the projected area method suggested by most of classification societies. Three loading conditions according to the bearing offset and the hydrodynamic moment and twelve models according to the locations of the effective support points of sterntube bearings are prepared to carry out quantitative verifications for an actual shafting system of 8000 TEU class container vessel. It is found that there is relatively large difference between assumed and calculated effective support points.

• 대한조선학회논문집
• /
• 제37권4호
• /
• pp.92-105
• /
• 2000

세장한 선박 판부재를 대상으로 가장 중요한 하중인 종방향 면내하중을 작용시키면서 이중판의 폭, 길이, 두께 및 주판(main plate) 부식 영향 등의 각종 파라메타 영향에 따른 이중판의 정적 강도평가를 주판의 접촉효과를 고려한 탄소성 대변형 비선형 시리즈 구조해석을 수행하였으며 이들 해석 결과로부터 각 파라메타의 변화에 따른 강성과 강도 특성을 분석하였다. 또한 이중판의 보강 효과가 최소한 새판으로 치환 보수한 평판 강도 수준으로 설계되어야 하므로 이를 손쉽게 파악할 수 있게 이중판으로 보강된 판부재를 등가 평판 두께로 환산할 수 있는 간이 평가식을 개발하였다. 이 개발식을 이용하여 각 이중판 설계의 영향인자 변화에 따른 등가 평판두께의 증감 정도를 파악하고 이로부터 적어도 새판으로 보수한 평판강도에 달할 수 있게 길이방향 일축 면내 압축하중을 받는 세장한 이중판의 설계지침을 제시하였다. 마지막으로, 개발된 등가 평판 도출식은 고정밀 좌굴강도 평가식과 서로 일정한 상관관계가 있음을 확인하고 관계식을 정립하였다. 이 관계식을 각 경우별로 축적하여 앞으로 일일이 구조해석을 수행하지 않고도 설계된 이중판 강도를 등가 평판두께로 제시할 수 있는 간이 추정식의 개발에 이용될 수 있을 것으로 사료된다.

• Advances in concrete construction
• /
• 제7권2호
• /
• pp.117-126
• /
• 2019

When designing reinforced concrete (RC) members, the rebar is assumed to resist all tensile forces, but the resistance of the concrete in the tension area is neglected. However, concrete can also resist tensile forces and increase the tensile stiffness of RC members, which is called the tension stiffening effect (TSE). Therefore, this study assessed the TSE, particularly after yielding of the steel bars and the effects of the steel ratio on the TSE. For this purpose, RC member specimens with steel ratios of 2.87%, 0.99%, and 0.59% were fabricated for uniaxial tensile tests. A vision-based non-contact measurement system was used to measure the behavior of the specimens. The cracks on the specimen at the stabilized cracking stage and the fracture stage were measured with the image analysis method. The results show that the number of cracks increases as the steel ratio increases. The reductions of the limit state and fracture strains were dependent on the ratio of the rebar. As the steel ratio decreased, the strain after yielding of the RC members significantly decreased. Therefore, the overall ductility of the RC member is reduced with decreasing steel ratio. The yielding plateau and ultimate load of the RC members obtained from the proposed equations showed very good agreement with those of the experiments. Finally, the image analysis method was possible to allow flexibility in expand the measurement points and targets to determine the strains and crack widths of the specimens.

• Tribology and Lubricants
• /
• 제35권3호
• /
• pp.158-168
• /
• 2019

This paper presents the investigation of two types of rotordynamic modeling issues for 2.2 kW-class, rated speed of 1,800 rpm, squirrel-cage type induction motors. These issues include the lamination structure of rotor cores, and the radial clearance of ball bearings that support the shaft of the motor. Firstly, we focus on identifying the effects of rotor core lamination on the rotordynamic analysis via a 2D prediction model. The influence of lamination is considered as the change in the elastic modulus of the rotor core, which is determined by a modification factor ranging from 0 to 1.0. The analysis results show that the unbalanced response of the rotor-bearing system significantly varies depending on the value of the modification factor. Through modal testing of the system, the modification factor of 0.079 is proven to be appropriate to consider the effects of lamination. Next, we investigate the influence of ball bearing clearance on the rotordynamic analysis by establishing a bearing analysis model based on Hertz's contact theory. The analysis results indicate that negative clearance greatly changes the bearing static behavior. Rotordynamic analysis using predicted bearing stiffness with various clearances from -0.005 mm to 0.010 mm reveals that variations in clearance result in a slight difference in the displacement of the system up to 18.18. Thus, considering lamination in rotordynamic analysis is necessary as it can cause serious analysis errors in unbalanced response. However, considering the effect of the bearing clearance is optional because of its relatively weak impact.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.376-386
• /
• 2020

The aim of this study was to develop a new efficient strategy that uses the Vector form Intrinsic Finite-element (VFIFE) method to conduct the static and dynamic analyses of marine pipes. Nonlinear problems, such as large displacement, small strain, and contact and collision, can be analyzed using a unified calculation process in the VFIFE method according to the fundamental theories of point value description, path element, and reverse motion. This method enables analysis without the need to integrate the stiffness matrix of the structure, because only motion equations of particles established according to Newton's second law are required. These characteristics of the VFIFE facilitate the modeling and computation efficiencies in analyzing the nonlinear dynamic problem of flexible pipe with large deflections. In this study, a three-dimensional (3-D) dynamical model based on 3-D beam element was established according to the VFIFE method. The deep-sea flexible pipe was described by a set of spatial mass particles linked by 3-D beam element. The motion and configuration of the pipe are determined by these spatial particles. Based on this model, a simulation procedure to predict the 3-D dynamical behavior of flexible pipe was developed and verified. It was found that the spatial configuration and static internal force of the mining pipe can be obtained by calculating the stationary state of pipe motion. Using this simulation procedure, an analysis was conducted on the static and dynamic behaviors of the flexible mining pipe based on a 1000-m sea trial system. The results of the analysis proved that the VFIFE method can be efficiently applied to the static and dynamic analyses of marine pipes.

• 한국지반공학회논문집
• /
• 제38권9호
• /
• pp.45-52
• /
• 2022

암반내 불연속면이나 지반-구조물의 접촉면은 열-수리-역학적으로 연계된 거동 특성을 보이므로, 온전한 지배방정식에 근거한 경계면 요소의 개발이 필요하다. 본 논문은 경계면 요소에 대한 힘평형 방정식, 유체의 연속방정식 그리고 에너지 평형 방정식을 유도하였다. 그리고 경계면 요소에 대한 탄소성 역학 모델의 강성행렬을 제시하였다. 개발된 유한요소는 2차원 조건에서 변위는 6절점, 수압과 온도는 4절점을 사용한다. 단층내 유체 주입에 대한 완전연계된 THM 해석은 단층내의 유효응력 감소와 주위 암반의 온도 수축에 의한 주입압의 복합적인 변화을 모델링 할수 있었다. 하지만, 열적 현상을 무시한 HM해석은 수리-역학적 변수를 과다하게 산정하였다.

• 반도체디스플레이기술학회지
• /
• 제21권1호
• /
• pp.148-154
• /
• 2022

As the 4th industrial age approaches, the demand for semiconductors is increasing enough to be used in all electronic devices. At the same time, semiconductor technology is also developing day by day, leading to ultraprecision and low power consumption. Semiconductors that keep getting smaller generate heat because the energy density increases, and the generated heat changes the shape of the semiconductor package, so it is important to manage. The temperature change is not only self-heating of the semiconductor package, but also heat generated by external damage. If the package is deformed, it is necessary to manage it because functional problems and performance degradation such as damage occur. The package burn in test in the post-process of semiconductor production is a process that tests the durability and function of the package in a high-temperature environment, and heat dissipation performance can be evaluated. In this paper, we intend to review a new material formulation that can improve the performance of the adapter, which is one of the parts of the test socket used in the burn-in test. It was confirmed what characteristics the basic base showed when polyamide, a high-molecular material, and alumina, which had high thermal conductivity, were mixed for each magnification. In this study, functional evaluation was also carried out by injecting an adapter, a part of the test socket, at the same time as the specimen was manufactured. Verification of stiffness such as tensile strength and flexural strength by mixing ratio, performance evaluation such as thermal conductivity, and manufacturing of a dummy device also confirmed warpage. As a result, it was confirmed that the thermal stability was excellent. Through this study, it is thought that it can be used as basic data for the development of materials for burn-in sockets in the future.

• Steel and Composite Structures
• /
• 제48권3호
• /
• pp.275-291
• /
• 2023

This paper has focused on presenting vibration analysis of trapezoidal sandwich plates with 3D-graphene foam reinforced polymer matrix composites (GrF-PMC) core and FG wavy CNT-reinforced face sheets. The porous graphene foam possessing 3D scaffold structures has been introduced into polymers for enhancing the overall stiffness of the composite structure. Also, 3D graphene foams can distribute uniformly or non-uniformly in the plate thickness direction. The effective Young's modulus, mass density and Poisson's ratio are predicted by the rule of mixture. In this study, the classical theory concerning the mechanical efficiency of a matrix embedding finite length fibers has been modified by introducing the tube-to-tube random contact, which explicitly accounts for the progressive reduction of the tubes' effective aspect ratio as the filler content increases. The First-order shear deformation theory of plate is utilized to establish governing partial differential equations and boundary conditions for trapezoidal plate. The governing equations together with related boundary conditions are discretized using a mapping-generalized differential quadrature (GDQ) method in spatial domain. Then natural frequencies of the trapezoidal sandwich plates are obtained using GDQ method. Validity of the current study is evaluated by comparing its numerical results with those available in the literature. It is explicated that 3D-GrF skeleton type and weight fraction, carbon nanotubes (CNTs) waviness and CNT aspect ratio can significantly affect the vibrational behavior of the sandwich structure. The plate's normalized natural frequency decreased and the straight carbon nanotube (w=0) reached the highest frequency by increasing the values of the waviness index (w).

• 대한토목학회논문집
• /
• 제28권6D호
• /
• pp.895-904
• /
• 2008

장대레일은 동절기에 중위온도 이하로 떨어져 레일의 인장파단에 의해 개구부가 발생할 수 있다. 레일 파단을 미리 감지 못하는 경우에 개구부에서 동적하중에 의해서 차륜과 레일의 파손이 발생할 수 있으며, 열차주행 안전성이 감소될 수 있다. 본 연구에서는 개구부에서의 궤도와 차량의 동적거동 분석을 위해 레일 파단시 개구부에서의 궤도와 차량의 상호작용을 고려한 동적해석모델을 제안하였다. 궤도와 차량의 선형시스템은 비선형 헤르찌안 접촉 스프링에 의해 연성되었으며 전체 궤도-차량 시스템 운동방정식을 정식화하였다. 그리고 개구부에서의 상호작용 현상을 고려하여 궤도 불균일부의 함수를 정의하고 개구부에서의 전후방 레일 사이의 개구량을 고려하였다. 비선형 방정식을 풀기위해 동적해석은 $Newmark-{\beta}$ 방법에 의해 수행되었다. 그리고 차량속도, 개구량, 레일지지강성에 따른 매개변수에 대한 궤도-차량의 동적상호작용해석을 수행하였고 변수에 대한 영향을 분석하였다.

• 대한토목학회논문집
• /
• 제28권2A호
• /
• pp.207-214
• /
• 2008

본 논문에서는 연계논문에서 제안된 혼합구조 접합부의 개선정도를 확인하기 위하여 2개의 혼합구조 실험체에 대하여 4절점 휨시험을 수행하였다. 혼합구조 접합부의 거동 분석을 위하여 3차원 비선형해석 결과와 실재하 실험 결과를 하중-처짐 관계, 하중-변형률 관계, 접합부 개구폭, 균열과 파괴모드를 통하여 비교하였다. 3차원 비선형 해석을 위하여 접촉요소를 사용하였으며 해석프로그램은 범용 구조 해석프로그램인 아바쿠스를 이용하였다. 실험과 해석의 결과로부터 제안된 L 모양의 접합부가 휨하중에서 기존안보다 강성이 크게 나타났으며, 보다 나은 구조적 성능을 나타냄을 확인하였다.