Conductive SiC-$ZrB_2$ composites were produced by subjecting a 40:60 (vol%) mixture of zirconium diboride (ZrB2) powder and ${\beta}$-silicon carbide (SiC) matrix to spark plasma sintering (SPS). Sintering was carried out for 5 min in an argon atmosphere at a uniaxial pressure and temperature of 50 MPa and $1500^{\circ}C$, respectively. The composite sintered at a heating speed of $25^{\circ}C$/min and an on/off pulse sequence of 12:2 was denoted as SZ12L. Composites SZ12H, SZ48H, and SZ10H were obtained by sintering at a heating speed of $100^{\circ}C$/min and at on/off pulse sequences of 12:2, 48:8, and 10:9, respectively. The physical, electrical, and mechanical properties of the SiC-$ZrB_2$ composites were examined and thermal image analysis of the composites was performed. The apparent porosities of SZ12L, SZ12H, SZ48H, and SZ10H were 13.35%, 0.60%, 12.28%, and 9.75%, respectively. At room temperature, SZ12L had the lowest flexural strength (286.90 MPa), whereas SZ12H had the highest flexural strength (1011.34 MPa). Between room temperature and $500^{\circ}C$, the SiC-$ZrB_2$ composites had a positive temperature coefficient of resistance (PTCR) and linear V-I characteristics. SZ12H had the lowest PTCR and highest electrical resistivity among all the composites. The optimum SPS conditions for the production of energy-friendly SiC-$ZrB_2$ composites are as follows: 1) an argon atmosphere, 2) a constant pressure of 50 MPa throughout the sintering process, 3) an on/off pulse sequence of 12:2 (pulse duration: 2.78 ms), and 4) a final sintering temperature of $1500^{\circ}C$ at a speed of $100^{\circ}C$/min and sintering for 5 min at $1500^{\circ}C$.
There are many possibilities that recycled papers adulterate contaminants during the process. The objective of this research was to evaluate safety of paper-based packaging materials for food, especially commercial pizza boxes in Korea. Ultimately, we compared recycled and non-recycled commercial paper packaging materials. This study was based on Korean Food and Drug Administration (KFDA) regulation. PCBs were measured by GC-ECD. Arsenic and lead were analyzed using an ICP-MS. Formaldehyde was determined by LC-MS. Fluorescent materials were detected by UV lamp. The result of this study shows that non-recycled paper packaging materials meets all the tested hygienic specifications for food packaging materials, whereas recycled paper-based paperboard box may be contaminated by fluorescent whitening agent. Though these results need to be further studied, it is recommended to avoid using recycled paper in direct contact with food when used in food packaging.
As online fashion businesses achieve rapid growth in the last few years, they gather various kinds of customer information through customer registration procedures and expect to utilize this information for CRM programs. The purpose of this study were to understand the current practices of customer information management of online fashion companies and to discuss how to improve it for the benefit of both customers and fashion businesses. This study included three steps of empirical data collection process: First, online fashion companies were visited and content analyzed at three time periods-2002, 2003, and 2004. Second, a questionnaire was developed and surveyed with 488 customers. And third, interviews with two groups were conducted, one with customers who experienced customer registration with online fashion companies and the other with experts of web developing. Through customer registration procedures, personal and contact information such as name, citizen registration number(social security number), home address, home telephone number, and cellular phone number were most frequently required. Customers were asked to provide more specific information regarding their privacy, online behavior, and taste recently. The variety of information category in 2004 observation was larger than 2002, but the amount of required information from each company got smaller. Customers tended to provide some false infor- mation, and the most frequently cited reason for that was 'too much hassle' and 'no practical benefit from information provision'. Customers were concerned with the exposure of personal information such as citizen registration number. The ideal number of pieces of information required was identified as 3 to 5 including name, phone number, and address. The paper was concluded with the discussion of customer information management from CRM perspective, CRM program, information analysis methods, and security.
Journal of the Korean Society for Precision Engineering
/
v.28
no.7
/
pp.777-782
/
2011
Micro features on the surface are well-known to have significant effects on optical or mechanical properties such as the optical interference, reflectance at the surface, contact angle, interfacial friction, etc. These surface micro features are increasingly employed to enhance the functionality of the applications in various application areas such as optical components for LCD or solar panel. Diverse surface features have been proposed and some of them are showing excellent efficiency or functionality, especially in optical applications. Most applications employing the micro features need manufacturing process for mass production and the injection molding and roll-to-roll forming, which are typical processes for mass production adopting polymeric materials, may be also preferred for micro patterned plastic product. Since the functionality or efficiency of the surface structures generally depends on the shape and the size of the structure itself or the array of the structures on the surface, it would be very important to replicate the features very precisely as being designed during the molding the micro pattern applications. In this paper, a series of research activities is introduced for roll-to-roll forming of micro patterned film including filling of patterns with UV curable resin, demolding of surface structures from the roll tool, control of surface energy and cure shrinkage of resin and dispose time and intensity of the UV light for curing of UV curable resin.
Some RE (Zr, Nb, REE) ore deposits are located in the middle part of the Korean peninsula. Geotectonically, the RE ore deposits situated on the Kyemyeongsan Formation of northern margin of the Okcheon geosynclinal belt and in the transitional zone between Kyeonggi massif and Okcheon belt. The rare metal deposits distributed in Kyemyeongsan Formation which consists of schist and alkaline granite. The alkali granite has suffered extensive post-magmatic metasomatism and hydrothermal processes. The ore contains mainly Ce-La, Ta-Nb, Y, Y-Nb, Ti-Nb-(U), Nd-Th group minerals. Fergusonite, one of Nb-Y rich REE minerals belonging to the A-B oxides, is most common mineral in the rare metal deposits. The fergusonite bearing rocks may be devided into four types by occurrence features and mineral association, that is, zircon type, allanite vein, feldspar type, and fluorite type. Fergusonites show wide variations in optical properties, due to part of differences in their chemical composition (depending on the types), but also the degree of crystalinity of the individual specimens. Fergusonite metamicts enclosed in biotite are generally surrounded by well developed pleochroic haloes. Usually, fergusonite is accompanied with zircon and other REE-bearing minerals. Petrographical and chemical data are presented for fergusonites which collected different types. $Nb_2O_3$ and $Y_2O_3$ contents range from 48.51 to 53.01 wt.% and 29.18 to 42.02 wt.% respectively. Also, $ThO_2$, (1.83~6.93), $UO_2$, (0.17~2.84), ${\sum}RE_2O_3$ (except to Y) (1.11~8.73), and $TiO_2$, (0.19~1.19 wt.%) contents show variational compositions according to fergusonite types. The ${\sum}RE_2O_3$ of fergusonites are positive relation with $Y_2O_3$ and negative relaton with $ThO_2$ and $({\sum}{RE_2O_3}-{Y_2O_3})$. The $Nb_2O_3$ is sightly negative relation with $Ta_2O_3$. Back-scattered electron microscope images (BEI) of fergusonite show the mineral composition and textural feature is very complicated. The variation of Nb, Th and REE content of fergusonite and the modes of occurrence of mineral, suggests that REE may have been mobilized during the circulation of hydrothermal fluids related to contact metamorphism (metasomatism). The chemical variation of the fergusonites with occurrences and mineral association can be related to metasomatism of alkaline fluid was probably the dominant ore-forming process in Chungju district.
To preserve steel cultural properties on display outdoors, the surface of these relics is processed with a covering treatment, which is a typical anti-corrosion method. Since the registered cultural heritage of Korea No. 78 Locomotive at Jangdan Station of Gyeongui Line will be treated by preservation process and displayed in the open outdoor area, effective surface covering agents were selected through testing to prevent the corrosion of the locomotive. The mixed wax are based on two types of microcrystalline wax which is one of regular surface covering agents for locomotives and bee‘s wax. For the weather resistance test, 3 types of wax were applied to each specimen of the locomotive and the specimens were tested in the Xenon-Arc Accelerated Weathering Tester for 1000 hours in accordance with the ISO 4892-1981 criteria and the test results were compared. As a result, on the surface of the specimen coated with the bee's wax, a whitening event appears after 400 hours which causes aging, and the specimens coated by the microcrystalline wax showed signs of a whitening event after 800 hours. The moisture contact angle with the microcrystalline wax coating was also less than with the bee's wax. Therefore, it was found that the high temperature microcrystalline wax is the most effective coating agent in terms of weather resistance and moisture blocking capability and the high temperature microcrystalline wax was adopted for coating the surface of the locomotive.
Journal of Korean Society of Environmental Engineers
/
v.28
no.6
/
pp.677-686
/
2006
This study was the effectiveness of two downflow BAF(Biological Aerated Filter) systems at conventional water treatment system. A BAF reactor placed in front of coagulation and sedimentation tanks(Mode A) and after coagulation and sedimentation tanks(Mode B) that were compared in terms of removal of suspended particles, organic matters, and ammonia nitrogen. The suspended particles removal efficiency was over 80% for both Mode A and B, although Mode A gave slightly better results. $BOD_5$ removal and nitrification efficiencies were more than 90% for both reactor. The organic matter and ammonia removals were also superior in the Mode A. The biofilm thickness and biomass increased as increment of EBCT and the upper part of reactor more about 30% than lower part. The specific oxygen uptake rate(SOUR) was higher the upper part of reactor and Mode A than the lower part of reactor and Mode B. A cost analysis showed that the Mode A system was more cost effectiveness. It could save the coagulant dose by about 67% and the chlorine demand by about 95%. The ideal place to put the BAF reactor was in front of the coagulation/sedimentation process.
Journal of the Korea Academia-Industrial cooperation Society
/
v.12
no.6
/
pp.2904-2912
/
2011
Water qualities in the decentralized water treatment plants do not frequently satisfy the water standard limit, in particular, fluoride and nitrate are notorious for the poor removal. In this study, an electro-adsorption equipped with carbon nonotube (CNT) electrodes were carried out to effectively remove the nitrate and fluoride in the decentralized water treatment plants. Two types of CNT electrodes, coating and sintering electrodes were applied. Coating electrodes were made based on different kinds of binder and sintering electrodes were made based on different sintering temperature. Removal of fluoride and nitrate when the coated electrodes with organic binder were used for electro-adsorption were 46 and 99.9% respectively, which were better performances than the coated electrodes with inorganic binder were used. On the other hand, removal of fluoride and nitrate when the electrodes sintered at higher temperature ($1,000^{\circ}C$) were 77 and 87% respectively, which were better performances than the electrodes sintered at lower temperature ($850^{\circ}C$). As a consequences, the electro-adsorption equipped with a CNT electrodes could be an potential alternative process for the removal of fluoride and nitrate in a decentralized water treatment plants if proper current density and contact time were applied.
A shipbroking is maritime service business, which is consist of market of freight, shipbuilding, sales & purchase and demolition for intermediation between customer and supplier. In this way, a shipbroking business has strong relationship with shipping industry and is also knowledge service business for creation additional value based on shipping, shipbuilding, financial and law etc. However, the research on the evaluation items and a method for shipbroking company were not carried out in previous research. In this paper, We defined evaluation items with three high level, six middle level and sixteen low level for evaluation of shipbroking service by expert's brainstorming and AHP(analytic hierarchy process) method. And also carried out survey to employees of shipbroking company as supplier and shipping company as customer. As a result of survey, result of service in high level, convenient of middle level and credibility of low level are evaluated highly, and also business credit rating, profit of customer, achievement of customer's object are considered to more important than others items. In case of comparison between group, a method of contact with client, problem-solving ability, good relationship with clients of international and domestic evaluated importantly in common.
Park, Chai-Soon;Mun, Mi-Seon;Hong, Gin-Hee;Lee, Jeoung-Eun
Women's Health Nursing
/
v.6
no.4
/
pp.549-565
/
2000
Comprehensive review of the literature was conducted to determine 1) selected risk factors and its impact that affect pregnancy outcome such as smoking, alcohol consumption, and substance abuse 2) these factors can facilitate future strategies for health promotion and prevention for both pregnant women and fetus. Review of literature were extracted from searching MEDLINE(1966 - Oct. 2000). CINAHL (1982 - Oct. 2000) and the domestic literature. The following factors were identified: 1. The effects of risk behaviors on pregnancy. ${\cdot}$Maternal smoking was associated with the occurrence of premature or LBW delivery, fetal growth retardation, extremities defects, heart defects and sudden infant death syndrome. ${\cdot}$Maternal alcohol consumption was associated with spontaneous abortion, premature or LBW delivery, morphologic/neurologic problems, especially fetal alcohol syndrome. ${\cdot}$Heroin was associated with withdrawal after birth in which were born to heroine addicts for gestational age and lung maturation in animal studies. ${\cdot}$Cocaine was associated with spontaneous abortion, abruptio placenta and a poor response to environmental stimuli. ${\cdot}$So far, the effects of caffeine on pregnancy was controversial, but severe caffeine consumption was associated with premature or LBW delivery, spontaneous abortion, still birth and dystocia. 2. Intervention methods and its effects identified were as follows ${\cdot}$Conducted intervention for smoking, alcohol and drug consumption were single or combined. ${\cdot}$Intervention methods were counseling, phone contact, mailing, use of educational videotape, booklet, support person and alternatives such as nicotine patch. ${\cdot}$The interventions increased the rates of smoking cessation during pregnancy and awareness of the risk of drug consumption, and decreased amount of alcohol consumption. ${\cdot}$The intervention outcome found positive effect on birth weight and length. 3. Our recommendations were as follows ${\cdot}$The personal and social cognition should be enhanced through education and the mass media. ${\cdot}$It's necessary to educate and give information of preconceptional care, planned pregnancy and early prenatal care for optimal pregnancy outcome. ${\cdot}$It's necessary to develop comprehensive assessment tool which is reliable and valid on smoking, alcohol consumption and substance abuse to identify supportive or interventional program.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.