• Korean Journal of Materials Research
• /
• v.29 no.10
• /
• pp.639-646
• /
• 2019

Ink-jet printing is a manufacturing process technology that directly prints a digitalized design pattern onto a substrate using a fine ink jetting system. In this study, environmentally friendly yellow aqueous ceramic ink is synthesized by mixture of distilled water, yellow ceramic pigment and additives for ink-jet printing. The graft polymer, which combines electrostatic repulsion and steric hindrance mechanism, is used as a surfactant for dispersion stability of aqueous ceramic ink. Synthesized ceramic ink with graft polymer surfactant shows better dispersion stability than did ceramic ink with PAA surfactant; synthesized ink also shows desirable ink-jet printability with the formation of a single ink droplet during printability test. Finally, ceramic ink printed on glass substrate and ceramic ink with graft polymer surfactant shows a high contact angle without surface treatment on glass substrate. Consequently, it is confirmed that the ceramic ink with graft polymer surfactant can achieve high printing resolution without additional surface treatment process.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.583-588
• /
• 2015

Flexible tactile sensors can provide valuable feedback to intelligent robots regarding the environment around them. This is especially important when robots such as, service robots share a workspace with humans. This paper presents a contact force measurement algorithm of a flexible tactile sensor. This sensor is manufactured by a direct-writing technique, which is one 3D printing method, using multi-walled carbon nano-tubes. An analog signal processing circuit has been designed and implemented to reduce noise contained in the sensor output. In addition, a digital version of the Butterworth filter was implemented by software running on a microcontroller. Through various experiments, characteristics of the sensor system have been identified. Based on three traits, an algorithm to detect the contact and measure the contact force has been developed. The entire system showed a promising prospect to detect the contact over a large and curved area.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.4
• /
• pp.652-657
• /
• 2013

In this study, we developed a counting method for non-contact ID cards using an optical fiber displacement sensor instead of the traditionally used friction counting method. The proposed method has the advantage of high speed and automated measurement. For counting non-contact ID cards, an H-type optical fiber sensor, jig part, and counting program are developed separately to build the system and adjust it. Through the experimental test results, it was confirmed that counting is possible with one type of international ID card and one type of financial security card based on ISO7810. Furthermore, by applying the proposed method to 100 ID cards 100 times repeatedly, it was confirmed that it has high accuracy and an error ratio of 0%. We experimentally demonstrated that the proposed counting method for non-contact ID cards using an optical fiber displacement sensor can perform measurements with high accuracy and high speed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.406-406
• /
• 2011

최근 결정질 실리콘 태양전지 분야에서는 태양전지의 Voc와 Isc의 증가를 통한 효율 향상을 목적으로 후면 passivation 박막에 대한 연구가 활발하게 진행되고 있다. Local-Back Contact Cell은 최적화된 후면 passivation 박막을 이용한 태양전지 제조방법이다. 본 연구에서는 고효율의 LBC 태양전지 개발을 위해 Rapid Thermal Oxide(RTO)를 이용한 후면 passivation 박막에 screen printing을 이용한 point contact 구조의 LBC 태양전지를 제작하고 그 특성을 분석하였다. 본 연구에 사용된 RTO 박막은 O2와 N2, 2L/min의 조건에서 $850^{\circ}C$에서 3분 동안 열처리하여 성장시켰다. 이렇게 성장된 박막은 3nm의 두께로 형성되어 passivation 효과를 나타내었으며, carrier lifetime 측정 결과 37.8us의 값을 나타냈다. 전면 ARC형성을 위해 RTO 박막 위에 PECVD를 이용하여 SiNx passivation 처리를 하였고, 그 결과 carrier lifetime은 49.1us까지 향상하였다. 후면의 전극 형성을 위해 screen printing 방법으로 Al point contact을 형성하여 local 한 BSF를 형성 시켰으며, 이후 후면 전극 연결을 위한 방법으로 300nm의 두께로 full Al evaporation 공정을 진행 하였다. 결과적으로 RTO 후면 passivation 박막에 Al point contact 형성을 통해 제작된 태양전지는, Suns-Voc 579mV, FF 82.3%, 16.7%의 효율을 달성하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.7
• /
• pp.571-574
• /
• 2010

Surface recombination loss should be reduced for high efficiency of solar cells. To reduce this loss, the BSF (back surface field) is used. The BSF on the back of the p-type wafer forms a p+layer, which prevents the activity of electrons of the p-area for the rear recombination. As a result, the leakage current is reduced and the rear-contact has a good Ohmic contact. Therefore, the open-circuit-voltage (Voc) and fill factor (FF) of solar cells are increased. This paper investigates the formation of the rear contact process by comparing aluminum-paste (Al-paste) with pure aluminum-metal(99.9%). Under the vacuum evaporation process, pure aluminum-metal(99.9%) provides high conductivity and low contact resistance of $4.2\;m{\Omega}cm$, but It is difficult to apply the standard industrial process to it because high vacuum is needed, and it's more expensive than the commercial equipment. On the other hand, using the Al-paste process by screen printing is simple for the formation of metal contact, and it is possible to produce the standard industrial process. However, Al-paste used in screen printing is lower than the conductivity of pure aluminum-metal(99.9) because of its mass glass frit. In this study, contact resistances were measured by a 4-point probe. The contact resistance of pure aluminum-metal was $4.2\;m{\Omega}cm$ and that of Al-paste was $35.69\;m{\Omega}cm$. Then the rear contact was analyzed by scanning electron microscope (SEM).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.154-159
• /
• 1995

To achieve a high aspect ration of metal contact, buried contact solar cell scribe the silicon surface using laser. The Q-switched NdLYAG laser which has 1.064$\mu\textrm{m}$ wavelength use for silicon scribing with 25~40$\mu\textrm{m}$ width and 20~200$\mu\textrm{m}$ depth capabilities. The 2~3% shading losses are very low campared to the screen printing solar cell. In this paper, we investigate the silicon scribing theory and pratice, scribing system for BCSC processing.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.1
• /
• pp.30-36
• /
• 2002

The objective of this study was to investigate the viscosity of coating colors and ink-jet printing properties with different coating colors with various blending ratios of silica based pigments. The volume of pigments was measured to evaluate the effect of the pigments on the viscosity of coating colors. Contact angle, the change of ink diameter, optical density, and the area and perimeter of a printed let-ter were evaluated to examine the effect of the ink absorption on the ink-jet printing properties. Generally, as the amount of silica pigments Increased the ink-jet printing quality improved. But this caused an increase of the overall coating viscosity.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.22 no.2
• /
• pp.139-150
• /
• 2004

Development of the paper coating technologies to prevent print mottle is needed to obtain high quality printing. Printing mottle is recognized as the most common printing problems in using coated paper and which is one of the most difficult problems to solve in offset printing. Print mottle is one of the most important quality properties of printed products and manufacturers strive to improve the paper surface to gain higher and more even print mottle. The prevention of printed mottle requires of coating color formation, especially the minimum of binder migration. The results the uniformity of liquid absorption by paper at very short contact time between paper and testing printing liquids.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.689-693
• /
• 2005

Inkjet printing is a non-contact and direct writing associated with a computer. In the industrial field, there have been many efforts to utilize the inkjet printing as a new way of manufacturing, especially for electronic devices. For the application of inkjet printing to electronic field, one of the key factors is exact realization of designed images into printed patterns. In this work, micro patterning for conducting line has been studied using the piezoelectric print head and silver nano ink. Dimensions of printed images have been predicted in terms of print resolution and diameter of a single dot. The predicted and the measured values showed consistent results. Using the results, the design capability for industrial inkjet printing could be achieved.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.116-120
• /
• 2020

In this paper, we developed an electrochemical glucose sensor strip using a paper substrate. The paper glucose sensor strip is eco-friendly because it uses paper as a substrate, and it has the advantage that it can be manufactured only with four printing, drying and cutting processes. The paper glucose sensor is significantly simplified by the production process than the conventional glucose sensors because the production of only four printing on the paper substrate. In this paper, eco-friendly tracing paper was used to develop a paper glucose sensor strip, and screen-printing technology was used to form a carbon/silver electrode, insulating layer and glucose oxidase(GOD) layer. The developed paper glucose sensor strip has a flat structure with a size of 30 × 4.6 ㎟, and blood injection is a type of direct contact with the exposed enzyme layer above the strip. In this paper, the performance of paper glucose sensor strips was evaluated by analyzing the cyclic voltammetry(CV) and chronoamperometry(CA) characteristics.