• 한국전기전자재료학회논문지
• /
• 제20권9호
• /
• pp.749-755
• /
• 2007

Recently, novel MEMS probe cards can support reliable wafer level chip test with high density probing capacity. However, manufacturing cost and process complexity are crucial weak points for low cost mass production. To overcome these limitations, we have developed micro spring structured MEMS probe card. For fabrication of micro spring module, a wire bonder and electrolytic polished gold wires are used. In this case, stringent tension force control is essential to guarantee the low level contact resistance of micro spring for reliable probing performance. For this, relation between tension force of fabricated probe card and contact resistance is characterized. Compare to conventional probe cards, developed MEMS probe card requires fewer fabrication steps and it can be manufactured with lower cost than other MEMS probe cards. Also, due to the small contact scratch patterns, we expect that it can be applied to bumping types chip test which require higher probing density.

• 한국수소및신에너지학회논문집
• /
• 제21권4호
• /
• pp.295-300
• /
• 2010

Metal bipolar plate applied to Polymer Electrolyte Membrane Fuel Cell is getting most attractive due to their good feasibility of mass production and low cost. But it is one of the immediate causes of performance decline because it is difficult to reduce channel pitch of metal bipolar plate. In this study, mesh was inserted in between bipolar plate and GDL to obtain uniform contact pressure without reducing channel pitch. The section measuring and performance test were carried out to confirm the mesh structure distributes contact pressure equally in reacting area. The performance of 3 type mesh structures developed in this study were higher than the normal cell at all over the current range. Especially, it showed that the mesh cell performance was increased and pressure drop was decreased with diminishing mesh gap size. The Mesh structure was more sensitive to humidification and contact pressure change than the normal cell.

• 소음진동
• /
• 제11권2호
• /
• pp.336-345
• /
• 2001

This research presents a nonlinear model to analyze the ball bearing nitration due to the waviness in a rigid rotor supported by multi-row ball bearings. The waviness of a ball and each races is modeled by the superposition of sinusoidal function, and the position vectors of inner and outer groove radius center are defined with respect to the mass center of the rotor in order to consider five degrees of freedom of a general rotor-bearing system. The waviness of a ball bearing is introduced to these position vectors to use the Hertzian contact theory in order to calculate the elastic deflection and nonlinear contact force resulting from the waviness while the rotor has translational and angular motion. They can be determined by solving the nonlinear equations of motion with five degrees of freedom by using the Runge-Kutta-Fehlberg algorithm. Numerical results of this research are validated with those of prior researchers. The proposed model can calculate the translational displacement as well as the angular displacement of the rotor supported by the multi-row ball bearings with waviness. It also characterizes the nitration frequencies resulting from the various kinds of waviness in rolling elements, the harmonic frequencies resulting from the nonlinear load-deflection characteristics of ball bearing. and the sideband frequencies resulting from the waviness interaction.

• Journal of Astronomy and Space Sciences
• /
• 제20권4호
• /
• pp.249-260
• /
• 2003

1998년 12월부터 1999년 5월까지 총 10일간 W UMa형 접촉쌍성 AH Cnc를 소백산천문대의 61cm 망원경과 PM512 CCD 카메라, 그리고 BVI 필터를 사용하여 CCD 측광을 수행하였다. 새롭게 얻은 BVI 광도곡선을 Wilson-Devinney 쌍성모델의 Mode 3(접촉형)으로 분석해서 측광해를 구하고 Roche 모형을 얻었다. 지금까지 발표된 모든 극심시각들과 이번 관측자료를 사용하여 얻은 (O-C)도를 분석해서 영년주기 증가율와 질량이동률을 계산하였다.

• 대한기계학회논문집B
• /
• 제28권9호
• /
• pp.1093-1100
• /
• 2004

Numerical analysis of the heat transfer associated with droplet impact on a hot solid surface is performed by solving the equations governing conservation of mass, momentum and energy in the liquid and gas phases. The deformed droplet shape is tracked by a level set method which is modified to achieve volume conservation and to include the effect of contact angle at the wall. The numerical method is validated through the calculations for the cases reported in the literature. Based on the numerical results, the heat transfer rate is found to depend strongly on the droplet spread radius. Decreased advancing/receding contact angles enlarge the splat radius and in turn enhance the wall heat flux. The effect of impact velocity on the droplet spread is reduced as the droplet size decreases. Also, droplet atomization is observed to significantly enhance the heat transfer rate and the effect is pronounced for a smaller size of droplet. An existing model equation to predict the maximum spread radius is improved for application to a micro droplet.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1365-1381
• /
• 1990

본 연구에서는 Kant 등이 제안한 고차판이론의 C연속변위 유한요소 모델을 사 용하여 충격자와 적층판의 저속 충격 응답에 대하여 연구하여 그 결과를 Mindlin의 판 이론에 의한 계산 결과와 비교하고, 경계 조건의 영향 및 충격자의 충격속도, 질량변 화에 대한 접촉력의 변화를 고찰하고자 한다.

• 한국운동역학회지
• /
• 제28권3호
• /
• pp.159-164
• /
• 2018

Objective: The aims of this study were to determine the impact peak force and kinematic variables in running speed and investigate the relationship between them. Method: Thirty-nine male heel strike runners ($mean\;age=21.7{\pm}1.6y$, $mean\;mass=72.5{\pm}8.7kg$, $mean\;height=176.6{\pm}6.1cm$) were recruited in this investigation. The impact peak forces during treadmill running were assessed, and the kinematic variables were computed using three-dimensional data collected using eight infrared cameras (Oqus 300, Qualisys, Sweden). One-way analysis of variance ANOVAwas used to investigate the influence of the running speed on the parameters, and Pearson's partial correlation was used to investigate the relationship between the impact peak force and kinematic variables. Results: The running speed affected the impact peak force, stride length, stride frequency, and kinematic variables during the stride phase and the foot angle at heel contact; however, it did not affect the ankle and knee joint angles in the sagittal plane at heel contact. No significant correlation was noted between the impact peak force and kinematic variables in constantrunning speed. Conclusion: Increasing ankle and knee joint angles at heel contact may not be related to the mechanism behind reducing the impact peak force during treadmill running at constant speed.

• 한국전기전자재료학회논문지
• /
• 제24권4호
• /
• pp.328-332
• /
• 2011

The formation of front metal contact silicon solar cells is required for low cost, low contact resistance to silicon surface. One of the front metal contacts is Ni/Cu plating that it is available to simply and inexpensive production to apply mass production. Ni is shown to be a suitable barrier to Cu diffusion into the silicon. The process of Ni electroless plating on front silicon surface is performed using a chemical bath. Additives and buffer agents such as ammonium chloride is added to maintain the stability and pH control of the bath. Ni deposition rate is found to vary with temperature, time, utilization of bath. The experimental result shown that Ni layer by SEM (scanning electron microscopy) and EDX analysis. Finally, plated Ni/Cu contact solar cell result in an efficiency of 17.69% on $2{\times}2\;cm^2$, Cz wafer.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.67-70
• /
• 2004

An investigation was performed to study the impact damage of the laminated composite plates caused by a low- velocity foreign object with multi-scale modeling based on the concepts of Direct Numerical Simulation (DNS)[4]. In the micro-scale part, we discretize the composite plates through separate modeling of fiber and matrix for the local microscopic analysis. A micro-scalemodel was developed for predicting the initiation of the damage and the extent of the final damage as a function of material properties, laminate configuration and the impactor's mass, etc. Anda macro-scale model was developed for description of global dynamic behavior. The connection betweenmicroscopic and macroscopic is implemented by the tied interface constraints of LS-DYNA contact card. A transient dynamic finite element analysis was adopted for calculating the contact force history and the stresses and strains inside the composites during impact resulting from a point-nose impactor. The low-velocity impact events such as contact force, deformation, etc. are simulated in the macroscopic sense and the impact damages, fiber-breakage, matrix cracking and delamination etc. are examined in the microscopic sense.

• Journal of Microbiology and Biotechnology
• /
• 제8권5호
• /
• pp.478-483
• /
• 1998

For the enhanced production of a cardiac glycoside, digoxin, using in situ adsorption by biotransformation from digitoxin in plant cell suspension cultures, selection of proper resins was attempted and the culture conditions were optimized. Among various kinds of resins tested, Amberlite XAD-8 was found to be the best for digoxin production in considering adsorption characteristics as well as the effect on cell growth. Adequate time for resin addition was determined to be 36 h from the beginning of biotransformation and the presence of resins should be as short as possible to increase the productivity. In addition, to prevent the cells from direct contact with resin particles, immobilized systems were designed and examined. Immobilization further improved the advantages of in situ adsorption. It was confirmed that the increase of the contact area for mass transfer was an important factor in utilizing an immobilized system to enhance digoxin production.