• Macromolecular Research
• /
• 제9권5호
• /
• pp.253-258
• /
• 2001

Crosslinked poly(ethylene glycol)s (PEGs) were prepared by ultraviolet irradiation of low molar mass, liquid PEGs in the presence of benzophenone (BP) as a photoinitiator. The networks obtained have been characterized by DSC, IR, and contact angle measurements, and their water absorption and equilibrium swelling have been examined. The percent of gel formed and degree of swelling of the networks in water were dependent on the amount of BP in the reaction mixture, irradiation time and molar mass of PEG. Gel fraction yield exceeded 84%, and equilibrium swelling in water varied from 49 to 244%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.143-146
• /
• 2009

The metal-supported SOFC has beed developed as a new concept of SOFC which has higher mechanical strength. However, the mass transfer rate in this type of SOFC may be decreased due to the contact layer and the support layer and that can cause the low performance. Therefore, numerical analysis of the heat and mass transfer characteristics in a metal-supported solid oxide fuel cell(SOFC) is studied in this paper. Governing equations and electrochemical equations are calculated simultaneously. And the numerical results are compared with the experimental results for the code validation. The current density, temperature, and pressure drop are suggested as numerical results.

• 설비공학논문집
• /
• 제14권6호
• /
• pp.519-524
• /
• 2002

An experimental study has been conducted to investigate the effects of surface energy on frost formation. Test samples with two different surfaces are installed in a wind tunnel and exposed to a humid airflow. Dynamic contact angles (DCA) for these surfaces are $23^{\circ}\;and\;88^{\circ}$, respectively. The thickness and the mass of frost layer are measured and used to calculate the frost density while frost formation is visualized simultaneously with their measurements. Results show that frost density increases as time increases at specific test conditions. The air Reynolds number, the airflow humidity and the cold plate temperature are maintained at 12,000, 0.0042 kg/kg and $-21^{\circ}C$, respectively. The surface with a lower DCA shows a higher frost density during two-hour test, but no differences in the frost density have been found after two hours of frost generation. Empirical correlations for thickness, mass and density are assumed to be the functions of the test time and DCA.

• 소음진동
• /
• 제2권1호
• /
• pp.49-59
• /
• 1992

The motion analysis of a translation device driven by a piezoelectric actuator is performed to identify the mechanics of impact drive mechanism and to find the maximum speed waveform. The translation device is modeled as a semidefinite two-degree-of-freedom system. The motion analysis includes effects of friction force between moving mass and contact surface, dynamics of voltage amplifier and piezoelectric elements, and hysteresis of piezoelectric actuator. Base on the model, simulation studies are carried out and then compared with experimental results. It is found that the error between moving distances obtained by analysis and experiment is less than 15% and that the actual motion of moving mass is well predicted by the analytical work, finally, precision positioning experiments are carried out by using a proximity sensor as a feedback sensor. Position control of moving mass is initiated by the maximum speed waveform and finely tuned by the scaled down waveform so that accurate positioning is accomplished within the resolution of the sensor.

• Mass Spectrometry Letters
• /
• 제7권1호
• /
• pp.21-25
• /
• 2016

Dual-channel nano-electrospray has recently become an ionization technique of great promise especially in biological mass spectrometry. This unique approach takes advantage of the mixing processes that occurs during electrospray. Understanding in more detail the fundamental principles influencing spray formation further study of the origins of the mixing processes: (1) in a Taylor cone region, (2) in charged droplets or (3) in both environments. The dual-channel emitters were made from borosilicate theta-shape glass tubes (O.D. 1.2 mm) and had a tip diameters of less than 4 μm. Electrical contact was achived by deposition of a thin film of an appropriate metal onto the surface of the emitter. The experimental investigation of the Taylor cone formation in a dual-channel electrospray emitter has been carried out by injection of polystyrene beads (diameter 3 μm) at very low concentrations into one of the channels of the non-tapered theta-glass tubes. High-speed camera experiments were set up to visualize the mixing processes in Taylor cone regions for dual-channel emitters. Mass spectra from dual nano-electrospray are presented.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.348-358
• /
• 2008

Unlike structures in the air, the vibration analysis of a submerged or floating structure such as offshore structures is possibly only when the fluid-structures is understood, as the whole or part of the structure is in contact with water. Through the comparision between the experimental result and the finite element analysis result for a simple cylindrical model, it was verified that an added mass effects on the cylindrical structure. Using the commercial FEA program ANSYS(v.11.0), underwater added mass was superposed on the mass matrix of the structure. A frequency response analysis of forced vibration in the frequency considered the dynamic load was also performed. It was proposed to find the several important modes of resonance peak for these fixed cylindrical type structures. Furthermore, it is expected that the analysis method and the data in this study can be applied to a dynamic structural design and dynamic performance evaluation for the ground and marine purpose of power generator by wind.

• Nuclear Engineering and Technology
• /
• 제47권7호
• /
• pp.907-914
• /
• 2015

The energetic steam explosion caused by contact between the high temperature molten core and water is one of the phenomena that may threaten the integrity of the containment vessel during severe accidents of light water reactors (LWRs). We examined the dependence of steam explosion loads in a typical reactor cavity geometry on selected model parameters and initial/boundary conditions by using a steam explosion simulation code, JASMINE, developed at Japan Atomic Energy Agency (JAEA). Among the parameters, we put an emphasis on the water pool depth that has significance in terms of accident mitigation strategies including cavity flooding. The results showed a strong correlation between the load and the premixed mass, defined as the mass of the molten material in low void zones (void fraction < 0.75). The jet diameter and velocity that comprise the flow rate were the primary factors to determine the premixed mass and the load. The water pool depth also showed a significant impact. The energy conversion ratio based on the enthalpy in the premixed mass was in a narrow range ~4%. Based on this observation, we proposed a simplified method for evaluation of the steam explosion load. The results showed fair agreement with JASMINE.

• 공업화학
• /
• 제9권3호
• /
• pp.394-398
• /
• 1998

실리콘의 모노머로 사용되고 있는 MCS의 합성 최적조건에 관한 연구를 수행하였다. 4원촉매계($CuCl/ZnCl_2/Sn/Cd$)와 원료규소로 부터 접촉물질을 제조한 후, 염화메틸과 반응시켜 MCS를 합성할 때 실험계획법에 따라 실험하고 해석하여 하나의 공정조건을 확립하였다. 접촉물질 50g, 교반속도 60rpm, 상압에서 최적반응온도와 MeCl 유량은 각각 $300-305^{\circ}C$와 $70-80cm^3/min$이었다. 또한 연속적으로 실험을 수행하여 최적공정조건을 확인하였으며, MeCl의 전환율 67%와 규소소모율 92%에서 평균반응속도는 170(g-MCS/hr.kg-Si), 평균선택도는 0.05이었으며, 연속식 실험결과로부터 총괄반응속도식의 파라미터와 최적압력을 구하였다.

• 멤브레인
• /
• 제21권3호
• /
• pp.236-246
• /
• 2011

본 연구에서는 기공의 크기가 $0.4{\mu}m$의 소수성 막인 폴리에틸렌 100가닥으로 모듈을 제작하여 직접접촉식과 동반기체식 막증류 과정에서 막의 양단의 온도차, 공급수의 염분농도, 그리고 냉각수/동반기체의 유량에 대해서 투과수의 플럭스를 측정하였다. 이론적으로는, 동반기체식 막증류는 직접접촉식 막증류 공정의 막의 투과측 표면과 냉각수 사이에 동반 기체층이 추가된 것으로 간주하였다. 이 동반기체층은 새로운 저항층과과 동반기체의 이동중 상변화된 수증기가 손실되는 것이 투과유속을 30% 정도 감소시키게 된다. 물질수지식을 이용하여, 기존의 식과는 다르게 보정계수(${\omega}$)를 넣어 직접접촉식 막증류와 동반기체식 막증류의 이론값을 실험값과 비교 분석하였다.

• 천문학회지
• /
• 제39권2호
• /
• pp.41-50
• /
• 2006

We present the results of new multi-color CCD photometry for the contact binary XZ Leo, together with reasonable explanations for the period and light variations. Six new times of minimum light have been determined. A period study with all available timings confirms Qian's (2001) finding that the O-C residuals have varied secularly according to $dP/dt\;=\;+8.20{\times}10^{-8}\;d\;yr^{-l}$. This trend could be interpreted as a conservative mass transfer from the less massive cool secondary to the more massive hot primary in the system with a mass flow rate of about $5.37{\times}10^{-8}\;M_{\odot}\;yr^{-l}$. By simultaneous analysis of our light curves and the previously published radial-velocity data, a consistent set of light and velocity parameters for XZ Leo is obtained. The small differences between the observed and theoretical light curves are modelled by a blue third light and by a hot spot near the neck of the primary component. Our period study does not support the tertiary light but the hot region which may be formed by gas streams from the cool secondary. The solution indicates that XZ Leo is a deep contact binary with the values of q=0.343, $i=78^{\circ}.8$, ${\Delta}(T_1-T_2)=126\;K$, and f=33.6 %, differing much from those of Niarchos et al. (1994). Absolute parameters of XZ Leo are determined as follows: $M_1=1.84\;M_{\odot},\;M_2=0.63\;M_{\odot},\;R_1=1.75\;R_{\odot},\;R_2=1.10\;R_{\odot},\;L_1=7.19\;L_{\odot},\;and\;L_2=2.66\;L_{\odot}$.