• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.687-687
• /
• 2013

In rearpoint contact solar cell and the PERC (passivated emitter rear contact) type cell, surfaces were passivated by SiO2 or Al2O3 to increase solar cell efficiency. Therefore, we have investigated the effect of surface passivation for crystalline silicon solarcell using mass-production atomic layer deposited (ALD) Al2O3. The patttern which consists of cylinders with 100um diameter and 5um height was formed by PR patterning on Si (100) substrate and then Al2O3 of about 10nm and 20nm thickness was deposited by ALD. The pattern in 10 nm Al2O3 film was removed by dipping in aceton solution for about 10 min but the pattern in 20 nm Al2O3 film was not. The influences of process temperature and heat treatment were investigated using microwave photoconductance decay (PCD) and Quasi-Steady-State photoconductance (QSSPC). The solar cell process used in this work combines the advantage of using the applicability of a selective deposition associated with a ALD passivation and the use of low-cost screen print for the contacts formation.

• 대한기계학회논문집
• /
• 제16권11호
• /
• pp.2049-2058
• /
• 1992

본 연구에서는 OHC형 캠-밸브 기구의 6자유도 집중 질량계 모델을 기본으로 하고, 밸브변위와 선회종동자(oscillating-follower or finger-follower)의 동적 스트 레인을 측정하여 모델의 타당성을 검증하고, 또 최적화 기법을 도입하여 밸브 개폐시 기, 밸브변위 그리고 최소 접촉력 등을 구속조건으로 주고 캠과 종동자 사이의 최대 접촉력을 최소화 시키도록 최적 캠 형상을 설계하였다. 그리고 설계된 캠을 정밀 가 공하여 최적화 설계의 타당성 및 접촉력을 실험을 통하여 검증하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권4호
• /
• pp.618-623
• /
• 2004

This paper has dealt with the heat storage characteristics of gel type micro size latent heat storage material slurry. The heat release operation to the gel type micro size latent heat storage material slurry was carried out using hot air bubbles by direct contact heat exchange. This experiment was carried out using phase change material of n-paraffin so the heat release amount is higher than cold water system. The parameters of this experiment were concentration of latent heat phase change material, height of heat release bath and inlet velocity of hot air. The main results obtained are as follows : (1) The effect of concentration of latent heat phase change material dispersed with water is very affective to the direct contact heat exchange between hot air and gel type micro size latent heat storage material slurry. (2) It is clarified that the most effective concentration of latent heat phase change material dispersed with water exists around 20mass% at this type of direct heat exchange model experiment.

• KSTLE International Journal
• /
• 제1권1호
• /
• pp.12-20
• /
• 2000

Nano-wear and friction of carbon overcoated laser-textured and mechanically-textured computer hard disk were characterised after contact start/stop (CSS) wear test. Various analytical and mechanical testing techniques were employed to study the changes in topography, roughness, chemical elements, mechanical properties and friction characteristics of the coating arising from the contact start/stop wear test These techniques include: the atomic force microscopy (AFM), the continuous nano-indentation test, the nano-scratch test, the time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and the auger electron spectroscopy (AES). It was shown that the surface roughness of the laser-textured (LT) bump and mechanically textured (MT) Bone was reduced approximately am and 7nm, respectively, after the CSS wear test. The elastic modulus and hardness values increased after the CSS test, indicating straining hardening of the top coating layer, A critical load was also identified fer adhesion failure between the magnetic layer and the Ni-P layer, The TOF-SIMS analysis also revealed some reduction in the intensity of C and $C_2$$F_59$, confirming the wear of lubricant elements on the coating surface.

• 대한기계학회논문집B
• /
• 제36권6호
• /
• pp.609-617
• /
• 2012

충돌, 퍼짐 및 수축을 포함한 나노입자 혼합 액적의 거동에 대한 수치모사를 수행하였다. 기체-액체 상경계면은 벽면에서의 접촉각 이력현상을 포함한 레벨셋 방법을 이용하여 해석하였다. 액적 내부의 나노입자 분포를 해석하기 위하여 물질의 열확산을 반영한 농도 방정식을 해석에 포함하였다. 수치해석 결과로부터 나노 입자의 분포는 온도의 불균일 분포에 크게 영향을 받는 것을 확인하였다. 나노입자의 농도 집중도에 의한 표면 장력 및 접촉각변화 효과에 대한 연구를 수행하였다.

• 한국수소및신에너지학회논문집
• /
• 제21권4호
• /
• pp.313-320
• /
• 2010

Carbon cloth was impregnated into PTFE emulsion. PTFE is a fluoropolymer used as a coating material in various fields due to its hydrophobicity and excellent mechanical properties. In this study, PTFE emulsion was prepared different particle size of 5~500 nm and $3{\sim}5{\mu}m$. FE-SEM and FT-IR spectroscopy were used microscopic observation and investigation of chemical structure change after PTFE coating. Mass variations, gas permeability and water contact angles were analyzed to determine a GDL performance of PTFE coated carbon cloth. PTFE coated carbon cloth show different mass increase according as PTFE concentration and the number of coating times. Water contact angle of PTFE coated carbon cloth was not effected by size of PTFE particle and the number of coating time; meanwhile, gas permeability was rapidly changed at carbon cloth coated by emulsion with size of $3{\sim}5{\mu}m$ PTFE particle.

• 한국운동역학회지
• /
• 제24권3호
• /
• pp.209-216
• /
• 2014

The purpose of this study was to explore the effect of 8 weeks after school classes of track sports on students' start motion through kinematic variables. 30 students in D National university of education participated for this study. These students divided into two groups, 17 students for experimental group and 13 students for control group. The two groups participated in general athletic class as common class, and the experimental group participated in after school class additionally. The general class taught track and jump skill for 3 hours a week, and the after school class taught only athletic running skill for 30 minutes a week. Pre and post test assessed to assess students' kinematic changes. Findings indicated that velocity and step rate were increased, and contact time, step length, displacement of center of mass were decreased in the experimental group. In the control group, early velocity, knee/hip angle velocity were increased, and contact time, step length, displacement of center of mass were decreased. In conclusion, the students who only participated in general class, could not maintain athletic skills obtained from the class. However, students who participated in both general and after school class accomplish athletic start skill. This is because Continuous learning effect helped students keep the skill and did not lose the skill. Thus, in order for students to learn specific sport skills, joining after school class with general class together is recommended.

• Mass Spectrometry Letters
• /
• 제1권1호
• /
• pp.9-12
• /
• 2010

Trimethylboroxine (TMB) is a six-membered ring compound containing Lewis acidic boron and Lewis basic oxygen atoms that can bind halide anion and alkali metal cation, respectively. We employed Fourier transform ion cyclotron resonance spectroscopy to study the gas-phase binding of $LiBrLi^+$ and $F^-(KF)_2$ to TMB. TMB forms association complexes with both $LiBrLi^+$ and $F^-(KF)_2$ at room temperature, providing direct evidence for the ditopic binding. Interestingly, the $TMB{\cdot}F^-(KF)_2$ anion complex is formed 33 times faster than the $TMB{\cdot}Li^+BrLi$ cation complex. To gain insight into the ditopic binding of an ion pair, we examined the structures and energetics of $TMB{\cdot}Li^+$, $TMB{\cdot}F^-$, $TMB{\cdot}LiF$ (the contact ion pair), and $Li^+{\cdot}TMB{\cdot}F^-$ (the separated ion pair) using Hartree-Fock and density functional theory. Theory suggests that $F^-$ binds more strongly to TMB than $Li^+$ and the contact ion-pair binding ($TMB{\cdot}LiF$) is more stable than the separated ion-pair binding ($Li^+{\cdot}TMB{\cdot}F^-$).

• 소성∙가공
• /
• 제12권2호
• /
• pp.128-133
• /
• 2003

In this study, the momentum conservation type punching mechanism for micropunching system was developed to avoid the punch failure in the misaligned status between the punch and die. The punching energy can be precisely controlled by the falling height of the projectile mass and the intermediata mass, which contacts with the punch, transmit the energy to the punch with the same contact condition. The potential energy of the projectile mass is converted to kinetic energy at the light weight punch that the projection speed into the sheet metal workpiece can be accelerated. The butt formation characteristics for the alignment condition and for the projection speeds are investigated to verify the feasibility of the proposed punching mechanism.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.155-161
• /
• 2009

Desiccant systems have been proposed as energy saving alternatives to vapor compression air conditioning for handling the latent load. Use of liquid desiccants offers several design and performance advantages over solid desiccants, especially when solar energy is used for regeneration. The liquid desiccants contact the gas inside the packed column and the heat transfer and mass transfer will occur. This proposal is try study the mass transfer and heat transfer inside the packed column of dehumidifier and regenerator systems. And later on, the rates of dehumidification and regeneration that were affected by desiccant flow rates, air temperature and humidity, and desiccant temperature and all that variation will influence the performance of the systems.