• 한국가스학회지
• /
• 제18권4호
• /
• pp.51-55
• /
• 2014

본 연구에서는 한곳에서 접촉하는 오링과 여러 곳에서 접촉하는 멀티접촉패킹에 대한 밀봉특성을 유한요소법으로 해석하였다. FEM 해석결과에 의하면, LP가스압력 1.8MPa을 공급하였을 때 기존의 오링에서는 밀봉성에 관련된 2.5MPa의 수직접촉 최대응력을 발생하였다. 반면에 새롭게 고안된 멀티접촉패킹에서는 3.01MPa이 발생하여 20.4%나 높아진 밀봉성이 향상되었음을 알 수 있다. 또한, 밀봉내구 안전성에 밀접한 관련이 있는 압출현상은 기존 오링의 경우 1.62MPa의 가스압력에서 발생되었지만, 멀티접촉패킹에서는 1.8MPa 정도로 가스내압을 올려도 압출현상이 발생되지 않는 것은 오랫동안 밀봉작용을 한다는 것을 의미한다. 따라서 밀봉성과 내구안전성을 높게 요구할 때는 한곳에서 접촉하는 기존의 오링보다는 여러 곳에서 접촉하는 멀티접촉패킹을 사용하는 것이 유리함을 알 수 있다.

• Tribology and Lubricants
• /
• 제39권4호
• /
• pp.154-166
• /
• 2023

This study establishes a numerical analysis model of the finite element overhung rotor supported by a DTRB and describes the stiffness properties of the DTRB. The vibration characteristics and contact pressure of the RBR system are predicted according to the DTRB support characteristics such as the initial axial compression and roller profile. The stiffness of the DTRB significantly varies depending on the initial axial compression and external load owing to the occurrence of rollers under the no-load condition and increase in the Hertz contact force. The increase in the initial axial compression increases the rigidity of the DTRB, thereby reducing the displacement of the RBR system and simultaneously increasing the natural frequency. However, above a certain initial axial compression, the effect becomes insignificant, and an excessive increase in the initial axial compression increases the contact pressure. The roller crowning radius, which gives a curvature in the longitudinal direction of the roller, decreases the displacement of the RBR system and increases the natural frequency as the value increases. However, an increase in the crowning radius increases the edge stress, causing a negative effect in terms of the contact pressure. These results show that the DTRB support characteristics required for reducing the vibration and contact pressure of the RBR system supported by the DTRB can be designed.

• 한국식생활문화학회지
• /
• 제38권6호
• /
• pp.442-455
• /
• 2023

This study investigated the effects of pectinase treatment and skin contact time on the quality characteristics of Dae-hong peach wine. Wine was produced with variations in enzyme treatment and skin contact time (1 hour, 2 hours, 1 day, 2 days, and until the completion of fermentation). Enzyme treatment increased the production yield by 6%, as well as ethanol and redness levels, compared to the non-treated control. Volatile components were higher when the skin contact time was 2 hours or 1 day. Results were compared according to enzyme treatment and skin contact time and found to be influenced by methanol and 3-methyl-1-butanol. Enzyme treatment effectively enhanced yields and volatile compound contents. However, skin contact should be concluded a day before 1 day to ensure compliance with methanol legislative requirements. Therefore, our findings show that enzymatic treatment with shorter skin contact time preserves the distinctive characteristics of Dae-hong peaches and ensures the production of safe and flavorful wine.

• 한국정밀공학회지
• /
• 제14권4호
• /
• pp.56-63
• /
• 1997

Sealing of lubricant-air mixture in the high performance machining center is one of most the important characteristics to carry out enhanced lubrication. High speed spindle requires non-contact type of sealing mechanism. Evaluating an optimum seal design to minimize leakage is concerned in the aspect of flow control. Effect of geometry and leakage path are evaluated according to variation of sealing geometry. Velocity, pressure, turbulence intensity of profile is calculated to find more efficient geometry and variables. This offers a methodological way of enhancement seal design for high speed spindle. The working fluid is regarded as two phases that are mixed flow of oil phase and air phase. It is more reasonable to simulate an oil jet or oil mist type high speed spindle lubrication. Turbulence and compressible flow model are used to evaluate a flow characteristic. This paper considers a design effect of sealing capability of non- contact type seals for high speed spindle and analyzes leakage characteristics to minimize a leakage 7 on the same sealing area.

• KSTLE International Journal
• /
• 제2권1호
• /
• pp.22-28
• /
• 2001

A resin bonded copper-graphite brush was investigated to evaluate the characteristics electrical signal transmission through a sliding contact as a function of the relative amount of graphite and copper in the brush. Particular attention was given to the correlation between electrical signal fluctuation and tribological properties in an electrical sliding contact system. A ring-on-block type tribotester was used for this experiment and the ring was made from pure copper. Results showed that a copper-graphite brush at a particular composition range exhibited the most stable frictional behavior with a minimum voltage drop. The amount of voltage drop at the friction interface was affected by the surface roughness, transfer film formation at the friction interface, and the real area of contact. Microscopic observations and the surface analysis showed a good agreement with the results from this experiment. The results also indicated that the electrical signal flunctuation was directly associated with the oscillation of the coefficient of friction during sliding by nanoscale variation of contacts at the friction interface.

• 로봇학회논문지
• /
• 제12권2호
• /
• pp.161-172
• /
• 2017

Foot mechanisms play the role of interface between the main body of robotic systems and the ground. Biomimetic design of the foot mechanism is proposed in the paper. Specifically, multi-chained and multiple contact characteristics of general foot mechanisms are analyzed and their advantages are highlighted in terms of impulse. Using Newton-Euler based closed-form external and internal impulse models, characteristics of multiple contact cases are investigated through landing simulation of an articulated leg model with three kinds of foot. It is shown that in comparison to single chain and less articulated linkage system, multi-chain and articulated linkage system has superior characteristic in terms of impulse absorption as well as stability after collision. The effectiveness of the simulation result is verified through comparison to the simulation result of a commercialized software.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권11호
• /
• pp.546-550
• /
• 2002

In this paper, Heterojunction phototransistors(HPT's) with an optically transparent ITO emitter contacts were fabricated. The ITO ohmic contacts were realized by employing thin imdium layer between the ITO and $n^+$-InP layers. The ITO contact was annealed at $250^{\circ}C$. The specific contact resistance of about $6.6{\times}10^{-4}{\Omega}cm^2$ was measured by use of the transmission line model (TLM). Heterojunction bipolar transistors (HBTs) having the same device layout were fabricated to compare with HPTs. The DC characteristics of the InP/InGaAs HPT showed the similar electrical characteristics of the HBT. Emitter contact resistance($R_E$) of about $6.4{\Omega}$ was extracted, which was very similar to that of the HBT. The optical characteristics of HPT's were generated by illuminating the device with light from $1.3{\mu}m$ light. It showed that HPT's can be controlled optically.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.620-623
• /
• 2000

The leaf spring is generally used effectively in load supporting because it has tension-diffused function in comparison with other springs. Nowadays the leaf spring is used widely in the suspensions of automobile and trains. The stiffness and the damping characteristics of the leaf spring being essential for the performance of vehicles, the exact evaluation is required. Various approximate formula are normally used for the leaf spring design. however, accuracy and trust are decreased because the contact and frictional characteristics between leaf plates are generally neglected. In this paper, nonlinear stiffness matrix of the leaf spring is solved by contact-element applying FEM for considering the contact and frictional characteristics between leaf plates. The results of proposed FE model are compared with test data.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권9호
• /
• pp.895-900
• /
• 1997

A Quench in cable-in-conduit (CIC) conductors is often initiated by a disturbance such as strand motion that generates a highly localized normal zone in a strand or a few strands of the CIC conductors. The localized normal zone causes current and heat transfer between a disturbed strand and neighboring strands. Electrical and thermal contact characteristics between strands thus have an effect on the transient stability of the CIC conductors. In this paper the effect of contact characteristics between strands on the CIC conductor stability is presented based on the measured heat transfer characteristics of supercritical helium (SHe) for the local heating. The quench and recovery processes of the strands for the abrupt and highly localized disturbance are analyzed at the boundary between quench and recovery.

• 한국분무공학회지
• /
• 제20권4호
• /
• pp.236-240
• /
• 2015

This study aims to experimentally investigate the evaporation characteristics of nanofluid droplet on heated surface at boiling temperature of DI-water. In particular, textured surface was used to examine the effect of wettability on evaporation. At the initial stage of evaporation process, dynamic contact angle (DCA) of nanofluid droplet with 0.01 vol.% concentration on textured surface rapidly increased over its equilibrium contact angle by generated large bubble inside the droplet due to lower wettability. However, contact angle of nanofluid droplet with higher concentration on textured surface decreased with surface tension. In addition, total evaporation time of droplet on textured surface was considerably delayed due to reduction of contact area between droplet and solid surface. Thus, evaporation characteristics were highly affected by the nanofluid concentration and surface wettability.