• Journal of Environmental Science International
• /
• v.17 no.2
• /
• pp.177-183
• /
• 2008

Characteristic of wastes in a unsanitary landfill at the residential development site in H city, Kyunggi-do was investigated for the disposal of huge amount of wastes. The total amount of wastes was estimated at 117,000 ton and construction solid wastes and municipal solid wastes were detected together. The portion of combustibles was very low and soils, concrete wastes, and pebbles were the major components in landfilled wastes. Because the site was the residential development site, the landfilled wastes should be removed immediately for the construction. Therefore the way that the unsanitary landfill was excavated and the wastes were sorted into three categories such as soils, noncombustibles and combustibles was selected as the best method. Soils and noncombustibles could be recycled and sorted combustibles could be re-landfilled in a smaller area or incinerated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.599-604
• /
• 1999

In recent years, problems of industrial solid wastes appear to be kind of national crises, caused by a sudden increase in their quantities, lack of disposal technique, and public discontent in installing plants for their disposal. This study is designed to investigate that pozzolana-based materials, such as blast furnace slag, fly-ash, paper sludge-ash, which are produced from industries as solid wastes, can be used as construction materials. The variations of concrete strength in function of compositional differences of raw materials including the wastes are studied experimentally. As a result, we find out that the blast furnace slag, the fly-ash, and the paper sludge-ash can be recycled as useful resources for replacement of cements by adjusting their substitution ratio.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2004.11a
• /
• pp.329-334
• /
• 2004

The objective of this study regards the preceding condition of the construction disposal of waste which is appropriate, with occurrence quantity DB anger the occurrence quantity prediction which is accurate the regression model which it sees and with the method which is mote accurate prediction method of existing than to sleep it presents it does. This study acquires apartment results data of public construction and civil construction, and chose factor that exert biggest influence on the waste occurrence amount through question and interview memorial address by regression model variable. And presented regression mode] which uses statistics program named SPSS. Result of this study by regression model through constant results data DB anger existent error big experience than estimate method that corrector estimation is available show.

• Environmental Engineering Research
• /
• v.25 no.1
• /
• pp.129-134
• /
• 2020

The main reason that drives many developing countries to pursue waste-to-energy (WtE) technologies is that it produces energy while eliminating build-up of large quantities of wastes, at a time, when oil and gas reserves are declining. The rate of generation of municipal solid wastes (MSW) in any given country depends on many factors including economy, population, and modernization of industry and infrastructure developments. The United Arab Emirates (UAE) is a federation of seven emirates that has grown to be one of the Middle East's most important economic centers. UAE has also become one of the highest waste producing countries due to fast development and growth; thus, UAE pursue modern technologies to covert generated wastes into energy. In this communication, the status of on-going waste to energy projects and WtE plants that are currently under design and construction in UAE are discussed. The need for development of WtE technologies is presented based on the literature, reports, economics and the environmental regulations.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.186-193
• /
• 2009

Since its opening in 1992, Sudokwon Landfill has become a landfill in which wastes generated from more than 22 million people are treated and disposed of. Its first phase landfill was closed in 2000 and the second phase landfill is in operation since then. The Korean environmental policies on refuse have drastically evolved for the last decade or so. From merely safe containment of wastes, the utilization of them as a source for energy generation and the minimization of waste volume to be filled in landfills are in the mainstream. Keeping in pace with the new trends, several challenging projects are in their way to blossom in Sudokwon Landfill. This paper briefs some important activities in the landfill. They are (1) geotechnical issues related to the construction and maintenance of the $1^{st}$ and $2^{nd}$ Landfills and (2) landfill gas and bioreactor which are recently emerging in the market.

• Structural Engineering and Mechanics
• /
• v.49 no.4
• /
• pp.491-498
• /
• 2014

During the past years, the protection of the environment has become a major concern out passing the state frontiers to reach a planetary dimension. Depository waste sites have become a serious problem in terms of their locations and costs. On the other hand, the construction industry has a leading place in terms of quantities of waste produced from the start to the end of each construction site, by the large amounts of raw materials used and their respective consequences on the environment. The recycling of quarry wastes products, of demolished concrete, bricks and large quantities of waste resulting from the transformation of marble blocks can provide ideal solutions and advantages for the preservation of the environment, to become a supplementary source of aggregates. The main purpose of this study is to show technically the possibility of recuperating the aggregates of marble wastes as a partial substitute or total in the mortars. The aggregates used in this study is a sand of marble wastes (excess loads of sand exposed to bad weather conditions) of the quarry derived from Fil-fila marble (Skikda, east of Algeria). To achieve this work, we have studied the effect of sand substitution of marble wastes in the mortar with rates of (25, 50, 75, 100%); comparing the results obtained with reference samples (0%), the properties when the samples are fresh, and the mechanical performances of mortars at solid state (loss and gain of weight, dimensional variations). The introduction of recycled sand in the mortars gives good results and can be used as granulates.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.6
• /
• pp.539-546
• /
• 2002

The physicochemical properties of solid wastes generated from seven highway service areas, four branch offices, and one construction site were analyzed in concert with air pollutants including heavy metals emitted from near-by small-scale incinerators. The amount of solid wastes generated from highway areas has been increasing with recent increases in the number of highways and passengers. Twelve incinerators examined in this study generally had capacity smaller than 100 kg/hr, most of which were equipped with cyclone for dust removal. It was seen that the concentrations of the gas-phase air pollutants (e.g., SO$_2$, NO$_{x}$, HCl and H$_2$S) were above the acceptable emission standards except one or two sites. CO concentrations at all incinerators were also higher due to incomplete combustion. In addition, particulate matters showed concentration six times higher at their maximum. The results of heavy metal analysis showed that the concentrations of Cu, Cd, and Ni satisfied the emission standards. whereas Pb at one site and Zn at five sites exceeded the standards. Cr measurement results indicated that 9 of 12 incinerators had higher values than the standard; especially one branch office showed nine times higher than normal concentration. In order to satisfy more stringent emission standards in the near future, it is necessary to install air pollution control system and to develop an intensified management plan.n.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.1
• /
• pp.29-36
• /
• 2009

Recycling of wood wastes or residues is a good solution for a shortage of wood resources and a rise in the price. Shipbuilding wood wastes were almost used to produce the boards by milling. However, considering the economic value and insufficient resource, recycling with milling is dissatisfied method. This study has been carried out to investigate the recycling possibility of shipbuilding wood waste. There are two kinds of shipbuilding wastes: plywood waste and solid waste. From the results of this study, the following conclusions have been made: 1. Bending properties of plywood and laminated plywood lumber were tested by Korean Standard. 2. The main fracture mode of plywood waste and laminated plywood lumber is that of simple tension. 3. The recommended application for the recycling of shipbuilding wood waste are outdoor wood furnishings, indoor wood furnishings and some wooden building construction materials: interior raw material, wooden pallet, siding, paneling, flooring. picnic table, deck components, porch swing, landscaping timbers, residential fencing, patios, and boardwalks etc.

• Journal of the Korean Professional Engineers Association
• /
• v.15 no.1
• /
• pp.46-50
• /
• 1982

Following rapid industrial development and urbanization in Korea, there is a need for the Government to implement effective control of pollution and to undertake specific schemes in areas where pollution of the environment is severe. In response to this need, Government of Korea prepare Han River Basin Environmental Master Plan Project for water, air, solid waste to cover environmental protection of the Han River Basin. The Project area is approximately 27,000 sq. Km extending over Seoul, Kyunggi, Kwangwon, Chungbuk Province. The total population of Master Plan Project area is approximately 11.6 million, or one-third of the total population of Korea. There are about 8,000 industries, including those located in 16 industrial complexes, in the project area. The scope of work and terms of reference are the following: (1) A Summary of existing land use and forecasts for changes in land use by the year 2,000. (2) Emission inventories for air, waste water, and solid wastes. (3) Forecasts of future population growth patterns and pollution loadings. (4) Identification of specific projects needs to reduce pollution levels and satisfy the environmental quality standards. (5) A Program of enforcement to include (i) self monitoring, and (ii) governmental inspections and surveillance. (6) A program for quality improvement and quality assurance of environmental measurements. (7) Reports summarizing all data collected analyzed during the study. (8) Conceptual design and feasibility studies, including cost estimates, for needed pollution control projects. (9) A financial plan for future detailed design and construction of public facilities, for financial incentives to industry, and for user charges for industrial use of public treatment of disposal works.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.2
• /
• pp.101-108
• /
• 2022

Centrifugal pumps are typically used in many slurry industries to transport solid materials. Solid particles in the slurry frequently shock the walls inside the pump, significantly abrading the flow path. Wear damage causes replacement of the pump components, which wastes manpower and time. Therefore, previous studies have been conducted on factors to improve efficiency and life time. This study identifies trends in pumps supplying lime to desulfurized devices from thermal power plants. The shear stress transport(SST) model is used to determine the erosion trend of the centrifugal pump that transfers lime slurry. The purpose of this study is to identify efficiency and erosion trends by selecting three of the various impeller design elements. The three impeller blade design variables mentioned above represent the inlet draft angle and blade angle of leading edge(L.E) and trailing edge(T.E). The maximum value of the erosion density rate tends to be similar to the Input power.