• Journal of the Korea Concrete Institute
• /
• v.22 no.1
• /
• pp.29-39
• /
• 2010

In this study, experimental test and numerical analysis were conducted to investigate the heat transfer characteristics and fiber performance of high strength concrete. The fire characteristics of the high strength concrete that couldn't be obtained through the test due to specific requirements and restrictions were forecast using numerical analysis approach. The outcome from the numerical analysis and the test were compared to verify and improve the reliability of the analysis. A numerical analysis of 80 and 100 MPa high strength concrete cases were carried out to identify the heat transfer characteristics and fire behavior using software, ABACUS (V6.8) From the results of verification experiment, a 25~55% level of beam shrinkage reduction was observed compared to the concrete without Fiber-Cocktail, indicating the improved fire resistance performance, which appeared to be attributable to the function of Fiber-Cocktail that was able to control the heat transfer characteristics and ultimately result in enhancing the fire resistance performance.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.1
• /
• pp.103-112
• /
• 2020

In Korea, local government officials are in charge of buildings, and as such are supposed to review submitted documents related to the architectural administration to ensure that they comply with the legal standards. However, these officials generally put a greater emphasis on the preparation of the set of documents required for the administrative work than the content the documents contain. For this reason, many experts point out that the shortage of officials specialized in buildings and construction, as well as the lack of expertise among the building officials in the local governments, may result in repeated safety accidents during building construction. The purpose of this study is to propose the operational direction of a Regional Building Safety (RBS) center to secure the performance and safety of buildings by utilizing private resources. In this study, we carried out a pilot project to verify the effects of an RBS center and to derive the specific number of experts required. As a result, the technical matters were resolved in approximately 15% of the total cases of the document processing procedure, and the level of technical specialization among the officers has also been improved through the provision of guidance. The research findings support the validity and effects of the introduction of the RBS center. Finally, this study proposes (1) the types of RBS Centers that should be established, (2) the roles and business scope of the RBS Center, (3) the specific number of experts required, (4) the qualifications of the experts, and (5) the business regulations of the RBS Center.

• Korean Journal of Construction Engineering and Management
• /
• v.7 no.5
• /
• pp.53-63
• /
• 2006

Since 2005, the government began to introduce and promote a new project delivery system, BTL(Build, Transfer, and Lease), in order to provide high level of public services for the upgraded quality of life and to boost the domestic and local construction economy. However, the lack of experiences in the new system by the constituents from diverse economic sectors brought a number of drawbacks from each constituent's perspective such as improperly low earning rate, excessive expenses for preparation of the project proposal, imbalanced regulations, heavy cost and procedures to establish SPC, the ineffective structure of the consortium, the short-term oriented evaluation criteria for the selection and so forth. These drawbacks turned out to be obstacles for the successful BTL projects. Hence, this paper analyzes the above issues and conducts the interviews with the professionals from the diverse sectors in order to propose the changes to resolve those for the improvement and finally to deliver the successful BTL projects for the diverse public owners.

• Korean Journal of Agricultural Science
• /
• v.23 no.2
• /
• pp.272-284
• /
• 1996

The present study has quantitatively assessed the regional production, income and employment impact resulting from the construction and operation of nuclear power plant (NPP) upon the domestic local areas by applying the regional input-output analysis model to the case of Wolsong unit-l site. The conclusions regarding the most likely regional economic impacts upon the wolsong site are summarized as follows: 1. The income multipliers are calculated to be 1.563 for the construction phase and 1.500 for the operation phase. These values are relatively high compared with those of other conventional facilities. 2. The level of total employee's wage induced employment associated with the construction phase has been estimated to be 37,000 while that with the operational phase in 1990 to be 5,610. 3. With relation to the aspect of resident welfare it is found that the industrial sector associated with electricity, gas and water supply have remarkably improved with the construction of the NPP. 4. The NPP siting has induced substantial changes in interindustry (input-output) structures of the Wolsong unit-l site which is one of the rural areas where all the domestic NPPs are sited. Such changes are attributed to the industrial recomposition of the region. 5. With the application of other regional economic analysis models and the use of more sufficient regional data, other detailed studies on the economic impact analysis of domestic NPP-related facility sitings are suggested to be carried out further since the influence of NPP sitings is significant to the national economic impact as well as the regional economic impact.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.3
• /
• pp.261-268
• /
• 2017

Red mud is an inorganic by-product obtained from the mineral processing of alumina from Bauxite ores. A highly alkali inorganic waste product with a pH level over 11, red mud in its original state negatively impacts the ecosystem, so appropriate treatment is necessary. The development of alkali activated slag-red mud cement can be a representative study aimed at recycling the strong alkali of the red mud as a construction material. However, Alkali-activated binders that use sodium activators have been reported to be more vulnerable to efflorescence. Therefore, in this study, the compressive strength, pore characteristics, water absorption, elution characteristics, and efflorescence properties of alkali-activated slag cement mortar were assessed according to their red mud substitution ratio.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.139-140
• /
• 2017

This technology employs a method of forming a single-ply PLUS waterproofing sheet layer comprised of applying a single-ply synthetic polymer layer on a vibrating structure (steel frame, RC) or an inclined surface by using a T joint lap-filling coil and an embedded metal coated sheet. The T - joint reinforcing lap-filling coil was used to block the ingress channel of the rainwater by applying the material in the vulnerable area where the three sides of the waterproof sheet overlapped. Conventional waterproofing techniques have a problem in that the waterproof sheet is pierced because the end portion of the waterproof sheet applied to the vertical portion is fixed by a nail, and the sealant applied to the end portion of the sheet cannot easily secure long-term waterproof durability due to the influence of the external environment. Therefore, the developed technology secured the waterproof durability against the vertical part by using the embedded metal sheet. In addition, automatic hot-air fusing is used to improve the quality of waterproof construction and point fixation method using fixed hardware. This is a technology that is not significantly restricted in the high degradation level regions of domestic waterproof construction environments in Korea such as low-temperature environment, wet floor.

• Korean Journal of Construction Engineering and Management
• /
• v.10 no.6
• /
• pp.88-98
• /
• 2009

Construction industries have increasingly utilized Building information Modeling (BIM) technologies. Interoperability - the capability for BIM data to run from one computer application to another in the life cycle of a project has become one of the principal research areas. Enhancing interoperability inevitably requires information structures that are standardized throughout the construction industries. As a candidate of the data exchange standard, Industry Foundation Classes (IFC) has been developed and several researches recently performed to measure its richness of digital data exchange. But doubts have been brought up whether IFC meets a sufficient level of interoperability since the research result revealed a number of cases of information misrepresentation and loss. This research presents the lessons learned from the interoperability tests of three widely used 3D design applications including Graphisoft's Archicad, Autodesk's Revit, and Bentley's Bentley Architecture. One building's architectural and structural design data were modeled with the three tools and exchanged through IFC respectively for interoperability test.

• Korean Journal of Construction Engineering and Management
• /
• v.9 no.4
• /
• pp.84-91
• /
• 2008

"Eco-friendly construction" is an emerging issue in the building industry. Main purpose of the eco-friendly construction is to sustain the health and environment of building residents and to minimize the harmful effect on their environment. Apartment residents have great concern on eco-product, since many cases are reported that Sick Building Syndrome is caused by toxic substance from building materials. Environmental performance is to meet through using the highest grade eco-friendly materials. However, generally eco-friendly materials are more expensive than normal materials, Therefore, using eco-friendly materials at public housing project is limited to economical aspect. The purpose of this paper is development of eco-friendly material selection model considered cost efficiency. The selection of Eco-friendly finishing materials and their methods are constructed to consider environmental performance level and cost index compositively. Development of eco-friendly material selection method is economic and reasonable one when public housing is constructed.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.953-956
• /
• 2007

"Eco-friendly construction"is an emerging issue in the building industry. Main purpose of the eco-friendly construction is to sustain the health and environment of building residents and to minimize the harmful effect on their environment. Apartment residents have great concern on eco-product, since many cases are reported that Sick Building Syndrome is caused by toxic substance from building materials. Environmental performance is to meet through using the highest grade eco-friendly materials. However, generally eco-friendly materials are more expensive than normal materials. Therefore using eco-friendly materials at public housing project is limited to economical aspect. The purpose of this paper is development of eco-friendly material selection model considered cost efficiency. The selection of Eco-friendly finishing materials and their methods are constructed to consider environmental performance level and cost index compositively. Development of eco-friendly material selection method is economic and reasonable one when public housing is constructed.

• Journal of the Korean Institute of Educational Facilities
• /
• v.18 no.4
• /
• pp.57-67
• /
• 2011

In this study, it did comparative analysis on the arrangement, construction and size of rooms applied in the early design stage at the time of prize-winning with the changed ground plans in the final design of those prize-winning works in design contests and BTL hold since 2007 for middle and high schools in Gyeonggi, Daejeon, Chungcheong regions. Through the analysis, this study intends to present those matters to be changed in the facilities standards of each local education office so that it can be referred to the assessment of spatial construction and proper size being planned in the future for middle and high schools and reflected flexibly in consideration of various educational conditions and characteristics of schools by regions. Furthermore, it has the objective to play a part for the establishment of much better environment of educational facilities by provision of reference materials to those matters being changed into proper ones not into the minimum ones of the school facilities standards as the national level. For case analysis, it analyzed various rooms classified by necessary spaces. Since names of rooms and spatial constructions to constitute facilities are different from each local education office and also the analysis by each room has some limitation in the changes and improvement of rooms for a wide range, it proceeded with detailed classifications of school building facilities by each necessary space.