• 농업과학연구
• /
• 제37권3호
• /
• pp.491-499
• /
• 2010

This study was carried out to investigate the consolidation characteristics of the remolded clay by the oedometer and the constant rate of strain(CRS) consolidation tests. As the rate of strain increases, the settlement rapidly decreased. As the ratio of the sand in the specimen increases, its effect on the rate of strain to the settlement was reduced. As the effective stress increased, the void ratio decreased, while the rate of strain increased, it did not show a clear variation. The reduction of the void ratio was shown to be less than the oedometer test. The coefficient of vertical consolidation with effective stress showed very large variation around preconsolidation stress, but the rate of strain did not provide significant effects. The rate of strain with effective stress gradually decreased at all tests and mixed ratio of sand. The rate of strain at the constant rate of strain tests showed smaller than in the oedometer test. The coefficient of consolidation at the constant rate of strain tests showed much more increase than in the oedometer test. The ratio of the vertical coefficient of consolidation by the odometer and the constant rate of strain tests showed a large difference according to various tests method and mixing ratio. Therefore, it is recommended that careful attention should be paid to designing the soft ground improvement.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1997년도 가을 학술발표회 논문집
• /
• pp.123-132
• /
• 1997

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1996년도 가을 학술발표회 논문집
• /
• pp.267-276
• /
• 1996

• 대한기계학회논문집A
• /
• 제21권6호
• /
• pp.925-932
• /
• 1997

Two shear-flexible curved axisymmetric shell elements with two nodes, LCCS(linear curvature and constant strain) and CCCS(constant curvature and constant strain) are designed based on the assumed meridional strain fields and shallow shell geometry. At the element level, meridional curvature, membrane strain and shear strain fields are assumed by using polynomials and the displacement fields are obtained by integrating the assumed strain fields along the shallowly curved meridian. The formulated elements have high order displacement fields consistent with the strain field. Several test problems are given to demonstrate the performance of the two elements. Analysis results obtained reveal that the elements are very accurate in the displacement and the stress predictions.

• 한국세라믹학회지
• /
• 제26권6호
• /
• pp.802-810
• /
• 1989

The temperature dependence of piezoelectric strain constant and the electric field induced strain are investigated as a function of PT in 0.5[xPT-(1-x)PZ]-0.5PNN ceramics. The piezoelectric strain constant d31 has the highest value(360$\times$10-12m/V) at PT=0.68. The temperature dependence of d31 is improved as Curie temperature of sample is increased, and the electric field dependence of induced strain is decreased with the coercive field increased. This ceramic system shows both piezoelectric effect and electrostrictive effect under the applied electric field. The piezoelectric of tetragonal phase is higher than that of rhombohedral phase, and the magnitude of electrostrictive constant is appeared in the order of morphotropic, rhombohedral and tetragonal phase. The piezoelectric strain constant with applied field must be considered theelectrostrictive effect due to 90$^{\circ}$domain wall displacements, and the displacement of bimorph type actuator agrees with the calulated value well.

• Geomechanics and Engineering
• /
• 제19권5호
• /
• pp.435-445
• /
• 2019

A series of element tests with different drainage conditions and strain rates were performed on compacted unsaturated non-plastic silt in unconfined conditions. Soil samples were compacted at water contents from dry to wet of optimum with the degree of saturation varying from 24 to 59.5% while maintaining the degree of compaction at 80%. The tests performed were shear infiltration tests in which specimens had constant net confining pressure, pore air pressure was kept drained and constant, just before the shear process pore water pressure was increased (and kept constant afterwards) to decrease matric suction and to start water infiltration. In constant water content tests, specimens had constant net confining pressure, pore air pressure was kept drained and constant whereas pore water pressure was kept undrained. As a result, the matric suction varied with increase in axial strain throughout the shearing process. In both cases, maximum shear strength was obtained for specimens prepared on dry side of optimum moisture content. Moreover, the gradient of stress path was not affected under different strain rates whereas the intercept of failure was changed due to the drainage conditions implied in this study.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.335-342
• /
• 2000

In this study, the swelling characteristics of reconstituted clayey soil were investigated by STD and CRS test. The strain rate during loading was constant i.e. 0.05 %/min, 0.03 %/min and during unloading was varied in proportion to 1/1, 1/5, 1/10 and 1/15 of strain rate during loading. From this study the following conclusions were obtained; (1) There were similar values, especially, during unloading in case of 1/10 or 1/15 of strain rate during loading and the test results between STD and CRS were much to be alike. (2) The cross point of effective stress versus excess pore water pressure ratio curve, was increased during unloading, while the stress level of the cross point was decreased. The stress level can be separated into two zones according to the swelling index named Cs1 and Cs2. From the test results, the values of Cs1 were approximately constant irrespective of strain rate during unloading, but the values of Cs2 were much influenced by strain rate. (3) In CRS consolidation tests, it was found that unloading strain rate did not affect on the existence of zone.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.180-183
• /
• 2004

Superplastic formability depends on flow parameters such as temperature, strain rate, strain and stress, microstructures. Usually, superplastic properties of materials are characterized with using a uni-axial tension testing. However, superplastic sheet is formed under mutiaxial loading condition in most forming practices. In the present study, superplastic characteristics of A15083 alloys were determined with using both a uni-axial and biaxial bulging tests. Specially, cone-type die was used to achieve constant strain rate under constant pressure condition. Even though constant strain rate under a certain pressure was achieved only approximately, a cone-type bulging test was found to be quite beneficial to get a multiaxial formability of superplastic materials.

• Geomechanics and Engineering
• /
• 제5권1호
• /
• pp.57-70
• /
• 2013

Constant rate of strain (CRS) consolidation tests were conducted for undisturbed Ariake clay samples from three boreholes in Saga Plain of Kyushu Island, Japan. The coefficients of consolidation ($c_{\nu}$) were interpreted from the CRS test results by small- and large-strain theory. Large-strain theory was found to interpret smaller $c_{\nu}$ values and less strain rate effect on $c_{\nu}$ than that by small-strain theory. Comparing the theoretical strain distributions within a soil specimen to those obtained by numerical simulation shows that the small-strain theory can be used only for the dimensionless parameter $c_{\nu}/\dot{\varepsilon}H_0^2{\geq}50$ (where $\dot{\varepsilon}$ is strain rate and $H_0$ is the specimen height), and the large-strain theory can be used for a larger range of strain rates. Applying the criterion to undisturbed Ariake clay with a $c_{\nu}$ value of about $1{\times}10^{-7}\;m^2/s$, it is suggested that the large-strain theory should be adopted for calculating the $c_{\nu}$ value when $\dot{\varepsilon}$ > 0.03%/min.

• Journal of Welding and Joining
• /
• 제12권4호
• /
• pp.151-161
• /
• 1994

FCAW has wide application in ship fabrication, maintenance and field erection. It has many advantages over SMAW.SAW and GMAW process. In many applications, the FCAW provides highquality weld metal. This method can reduce weld defects especially porosity and spatter. But the fatigue characteristics of those deposited metal have been rarely investigated. The purpose of this study is to investigate the cyclic stress-strain behavior and fatigue tests by the constant strain control were carried out on the rounded smooth specimen with deposited metal using the metal type flux cored wire. As the results of this study for the deposited metal welded by the metal type flux cored wire, the hardening or softening characteristics under cyclic load were investigated and cyclic stress-strain curve, strain-fatigue life curve, stress-strain function and fatigue life relation which are useful to estimate the fatigue life under the stress concentration condition were obtained.