• Computers and Concrete
• /
• v.26 no.3
• /
• pp.227-237
• /
• 2020

Strain rate investigations are needed to calibrate strain-rate-dependent material models and numerical codes. An appropriate material model, which considers the rate effects, need to be used for proper numerical modeling. The plastic concrete cut-off wall is a special underground structure that acts as a barrier to stop or reduce the groundwater flow. These structures might be subjected to different dynamic loads, especially earthquake. Deformability of a structure subjected to dynamic loads is a principal issue which need to be undertaken during the design phase of these structures. The characterization of plastic concrete behavior under different strain rates is essential for proper designing of cut-off walls subjected to dynamic loads. The Cowper-Symonds model, as one of the most commonly applied material models, complies well with the behavior of a plastic concretes in low to moderate strain rates and will be useful in explicit dynamics simulations. This paper aims to present the results of an experimental study on mechanical responses of one of the most useful types of plastic concrete and Cowper-Symonds constant determination procedures in a wide range of strain rate from 0.0005 to 107 (1/s). For this purpose, SHPB, uniaxial, and triaxial compression tests were done on plastic concrete samples. Based on the results of quasi-static and dynamic tests, the dynamic increase factors (DIF) of this material in different strain rates and stress state conditions were determined for calibration of the Cowper - Symonds material models.

• Geomechanics and Engineering
• /
• v.19 no.5
• /
• pp.435-445
• /
• 2019

A series of element tests with different drainage conditions and strain rates were performed on compacted unsaturated non-plastic silt in unconfined conditions. Soil samples were compacted at water contents from dry to wet of optimum with the degree of saturation varying from 24 to 59.5% while maintaining the degree of compaction at 80%. The tests performed were shear infiltration tests in which specimens had constant net confining pressure, pore air pressure was kept drained and constant, just before the shear process pore water pressure was increased (and kept constant afterwards) to decrease matric suction and to start water infiltration. In constant water content tests, specimens had constant net confining pressure, pore air pressure was kept drained and constant whereas pore water pressure was kept undrained. As a result, the matric suction varied with increase in axial strain throughout the shearing process. In both cases, maximum shear strength was obtained for specimens prepared on dry side of optimum moisture content. Moreover, the gradient of stress path was not affected under different strain rates whereas the intercept of failure was changed due to the drainage conditions implied in this study.

• Food Science and Biotechnology
• /
• v.18 no.4
• /
• pp.1013-1018
• /
• 2009

Several rheological terms were introduced to estimate the properties of cooked noodles with different starch content using tensile tests. Ring-shaped specimens were prepared by connecting both ends of the noodle strip before cooking. Hencky strain and rate, as well as true stress were applied in constant deformation tests. The elastic region on the curves of strain vs. stress was not clearly identified. Strain hardening in the subsequent plastic region was more prominent in low-starch noodles. Elongational viscosities at lower strain rates were used to differentiate noodles with different starch content, representing the dominant effect of protein content in the range of lower strain rates. In stress relaxation tests, the reciprocal of Peleg's constant $K_1$ (initial decay rate) and $K_2$ (asymptotic level) increased and decreased respectively, with an increase in starch content. This indicated that addition of starch contributed to the noodles becoming viscous liquid rather than elastic solid.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1998.10a
• /
• pp.455-460
• /
• 1998

This study performed to establish tile characteristics of constant rate of strain consolidation(CRSC) tests. The values obtained by the CRCS tests were compared with oedometer tests. From the comparision of the results of oedometer and CRSC tests for soft soil from Haenam, Korea, it was concluded that. 1. When rate of strain is 0.9mm/hr, compression curve of CRSC test was not coincided with those of tile oedometer test, then preconsolidation stress was larger than those of other rates of strain. 2. Permeabilities from CRSC tests and direct measurements were about same each other, but permeabilities from Oedometer tests were large than those from others.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.03a
• /
• pp.135-142
• /
• 1998

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.311-317
• /
• 2003

The swelling index of clayey soil was examined by constant rate of strain(CRS) consolidation test. Four kinds of strain rate were applied during unloading. The strain rates are l/l, l/5, 1/10, l/l 5 of loading. The strain rates during loading are 0.05%/min and 0.03%/min. From the test results using standard consolidometer, the swelling indexes were much similar values in case of 1/5 or 1/10 of the strain rate during loading stage. In the relation between effective stress and excess pore water pressure ratio, it was found that the existence of cross point and the stress level can be separated into two zones according to the swelling index.

• Korean Journal of Materials Research
• /
• v.26 no.5
• /
• pp.281-286
• /
• 2016

In the present study, the tensile properties and dynamic strain aging of an Fe-24.5Mn-4Cr-0.45C alloy were investigated in terms of strain rate. During tensile testing at room temperature, all the stress-strain curves exhibited serrated plastic flows related to dynamic strain aging, regardless of the strain rate. Serration appeared right after yield stress at lower strain rates, while it was hardly observed at high strain rates. On the other hand, strain-rate sensitivity, indicating a general relationship between flow stress and strain rate at constant strain and temperature, changed from positive to negative as the strain increased. The negative strain-rate sensitivity can be explained by the Portevin Le Chatelier effect, which is associated with dynamic strain aging and is dependent on the strain rate because it is very likely that the dynamic strain aging phenomenon in high-manganese steels is involved in the interaction between moving dislocations and point-defect complexes.

• Geomechanics and Engineering
• /
• v.5 no.1
• /
• pp.57-70
• /
• 2013

Constant rate of strain (CRS) consolidation tests were conducted for undisturbed Ariake clay samples from three boreholes in Saga Plain of Kyushu Island, Japan. The coefficients of consolidation ($c_{\nu}$) were interpreted from the CRS test results by small- and large-strain theory. Large-strain theory was found to interpret smaller $c_{\nu}$ values and less strain rate effect on $c_{\nu}$ than that by small-strain theory. Comparing the theoretical strain distributions within a soil specimen to those obtained by numerical simulation shows that the small-strain theory can be used only for the dimensionless parameter $c_{\nu}/\dot{\varepsilon}H_0^2{\geq}50$ (where $\dot{\varepsilon}$ is strain rate and $H_0$ is the specimen height), and the large-strain theory can be used for a larger range of strain rates. Applying the criterion to undisturbed Ariake clay with a $c_{\nu}$ value of about $1{\times}10^{-7}\;m^2/s$, it is suggested that the large-strain theory should be adopted for calculating the $c_{\nu}$ value when $\dot{\varepsilon}$ > 0.03%/min.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.99-106
• /
• 2000

The main advantage of incremental loading consolidation test is the simplicity of equipments that can be used. However, it is known that the incremental loading test has several deficiencies including long testing time, non-uniform stress state, high and variable rates of strain, very soft clay and problem of back pressure saturation. Due to these drawbacks, various testing methods including constant rate of strain consolidation test(CRS) were developed. In this paper, CRS consolidation test was performed with three different strain rate. The results were verified by the modified CRS theory of Wissa et al.(1971). And then the results obtained from the CRS consolidation tests were compared with those from incremental loading test and direct permeability test.

• Journal of Hydrogen and New Energy
• /
• v.26 no.4
• /
• pp.347-356
• /
• 2015

A study has been conducted numerically to investigate the lifted flat syngas flame structure of impinging jet flame configuration with the global strain rates in 10% hydrogen content. In this study, the effects of strain rate were major parameters on chemistry kinetics and flame structure at stagnation point. The numerical results were calculated by SPIN application of the CHEMKIN package. The strain rates were adjusted with Reynolds numbers of premixed syngas-air mixture. Different flame shapes were observed with different strain rates. As strain rate has increased, the flame temperature and axial velocity have been decreased due to the flame heat loss increment, and the OH radical reaction zones become narrower but each mole fractions are still constant. Also, the reversion of $H_2O$ product near stagnation point has been found out when strain rate has increased. This phenomenon is attributed to the rapid production of oxidizing radical reaction such as the R12 ($H+O_2(+M)=HO_2(+M)$), which makes the R18 ($HO_2+OH=O_2+H_2O$) reaction increment.