• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1694-1700
• /
• 2007

In the electrified section, both of return current and signal current are flowing in the same rail in common. But signal current shall be allowed to flow in the specific track circuit and not in the other circuit while the traction return current shall come back to power sub-station. This paper presents measuring system that use both sensor and antenna. The aim of the system is to achieve the difference in current between the two rails and the presence of trimming capacitors. In order to improve the transmission level, trimming capacitors are connected between the two rails at constant spacing. To maintain the balance of traction return current, rails of both sides may be jointed by the so-called SVPMM. The traction return current is sometimes unbalanced owing to the ill-contact of SVPMM. In this paper, we propose a diagnosis method based on a short-circuited current(Icc), trimming capacitors and traction return current measured by Korail inspection vehicles. Whether Icc is good or bad depends not only on the presence of trimming capacitors but also on the unbalance of the traction return current.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.47-52
• /
• 2002

A processing method is developed for preparing sol-gel derived $Pb(Zr_{1-x}Ti_x)O_3$ (x=0.5) thin films on Pt-Ir($Pt_{80}Ir_{20}$)-alloy substrates. The as-deposited layer was dried on a plate in air at $70^{\circ}C$. And then it was baked at $1500^{\circ}C$, annealed at $450^{\circ}C$ and finally annealed for crystallization at various temperatures ranging from $580^{\circ}C$ to $700^{\circ}C$ for 1hour in a tube furnace. The thickness of the annealed film with three layers was $0.3{\mu}m$. Crystalline properties and surface morphology were examined using X-ray diffractometer (XRD). Electrical properties of the films such as dielectric constant, C-V, leakage current density were measured under different annealing temperature. The PZT thin film which was crystallized at $600^{\circ}C$ for 60minutes showed the best structural and electrical dielectric constant is 577. C-V measurement show that $700^{\circ}C$ sample has window memory volt of 2.5V and good capacitance for bias volts. Leakage current density of every sample show $10^{-8}A/cm^2$ r below and breakdown voltage(Vb) is that 25volts.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.120-125
• /
• 2002

AC powder EL 소자를 절연층의 유전재료와 후면전극의 전기비저항을 변화시켜 스크린 프린팅법으로 제조하였다. 제조된 소자의 광전기적 특성을 평가하기 위하여 인가 전압은 50∼300 $V_{rms}$까지 변화시켜 휘도 및 전류밀도를 측정하였다. 주파수 및 전압공급원은 정현파 발생 장치로서 frequency generator를 이용하였다. 휘도는 luminometer 의해 측정되었으며 전류밀도 측정을 위하여 multimeter를 사용하였다. 또한 유전층에 대한 유전율을 후막 제조 후 impedance analyser(HP 4194 A)를 이용하여 측정하였다. $TiO_2$ 분말을 $BaTiO_3$에 첨가함에 따라 유전율의 향상으로 초저가형 AC powder EL 소자의 유전층에 적용함으로써 거의 비슷한 전류밀도 하에 50 cd/$m^2$ 정도의 향상된 휘도를 얻을 수 있었다. 저전력 소모형 AC powder EL 소자의 유전층에 적용시 상용분말을 이용한 경우보다 용액 연소법에 의해 제조된 $BaTiO_3$ 분말을 이용한 경우가 더욱 향상된 85 cd/$m^2$ 정도의 휘도를 얻을 수 있었다. 또한 후면전극의 전기 비저항을 조절함으로써 AC powder EL 소자의 휘도는 비교적 감소하지만 전류밀도를 낮출 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.114.1-114.1
• /
• 2011

Electrical sintering of the front electrode for crystalline silicon solar cells was performed applying a constant DC current to the printed lines. Conducting lines were printed on glass substrate by a drop-on-demand (DOD) inkjet printer and silver nanoparticle ink. Specific resistance and microstructure of sintered silver lines and were measured with varying DC current. To find the relation between temperature increase with changing applied current and specific resistance, temperature elevation was also calculated. Sintering process finished within a few milliseconds. Increasing applied DC current, specific resistance decreased and grain size increased after sintering. Achieved minimum specific resistance is approximately 1.7 times higher than specific resistance of the bulk silver.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2508-2511
• /
• 1999

A non-contact battery charger which transfers energy using magnetic field without any electrical contacts is designed using half-bridge series resonant converter. This converter utilizes series resonance to reduce the undesirable effect of large leakage inductance of the non-contact transformer and ZVS operation can reduce switching losses. In this paper. analysis and design procedure of half-bridge series resonant converter with non-contact transformer is presented. Input voltage is 85VAC ${\sim}$ 270VAC, output voltage and current is 4.1V and 800mA, respectively. Furthermore, a method for calculating the secondary current of the transformer to control battery charging current in constant current charging mode which is required for litium-ion battery is proposed and the performance is verified from experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.667-668
• /
• 2015

Synchronous Reluctance Motor (SynRM) has a simple structure with high efficient and without rotor conductor loss. Therefore, it is better than induction motor for electric vehicle (EV) on aspect of efficiency. SynRM usually operates on the constant torque region using maximum torque per ampere （MTPA）control which is adopted due to rotor structure limitation. Thus, the accurate current angle is crucial for motor control. However, finite element analysis (FEA) program is not sufficient exactly to regard how the iron loss and magnetic saturation influences on the current angle. Consequently, this paper proposed a method to calculate the current angle with consideration of iron loss.

• 전기학회논문지
• /
• 제61권5호
• /
• pp.690-697
• /
• 2012

Novel 8/10 bearingless switched reluctance motor, which can control rotor radial positions with magnetic force, is proposed. The motor has combined characteristics of switched reluctance motor and magnetic bearing. This paper proposes a air-gap control system method of suspending force control in a bearingless switched reluctance motor (BLSRM). The proposed radial force control scheme is independent to the torque winding current. A PI direct current control (DCC) controller and look-up table are used to maintain a constant rotor air-gap. From the analysis and the experimental results, it is shown that the proposed strategy is effective in realizing a naturally decoupled radial force control of BLSRM.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권4호
• /
• pp.265-271
• /
• 2000

A non-contact battery charger for cellular phone is designed using half-bridge series resonant converter. This converter utilizes series resonance to reduce the undesirable effect of large leakage inductance of the detachable transformer and ZVS operation can reduce switching loss and switching noise. In this paper, analysis and design procedure of half-bridge series resonant converter with detachable transformer is presented. The input voltage is 85VAC∼270VAC, and the output voltage and current is 4.1V and 800mA, respectively. Furthermore, a method of calculating the secondary current of the transformer to control the battery charging current in the constant current charging mode is proposed. The performance of the charger is verified through experiments.

• Journal of Electrical Engineering and Technology
• /
• 제6권5호
• /
• pp.647-657
• /
• 2011

The present paper proposes a sliding mode control with fixed switching frequency for three-phase three-leg voltage source inverter based four-wire shunt active power filter. The aim is to improve phase current waveform, neutral current mitigation, and reactive power compensation in electric power distribution system. The performed sliding mode for active filter current control is formulated using elementary differential geometry. The discrete control vector is deduced from the sliding surface accessibility using the Lyapunov stability. The problem of the switching frequency is addressed by considering hysteresis comparators for the switched signals generation. Through this method, a variable hysteresis band has been established as a function of the sliding mode equivalent control and a predefined switching frequency in order to keep this band constant. The proposed control has been verified with computer simulation which showed satisfactory results.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권4호
• /
• pp.7-10
• /
• 2007

The transport current distribution across the tape width of a SmBCO coated conductor was investigated. The current distribution was estimated by applying an inversion process to the field distribution measured in the vicinity of the tape by using a scanning Hall probe method. The obtained result is well consistent with one predicted by the Bean model, however, at the edges the current are not constant and do not generally plateau, on the contrary.