• 융복합기술연구소 논문집
• /
• 제3권1호
• /
• pp.19-23
• /
• 2013

This study is concerned with air-conditioning system in use of thermoelectric device. It is introduced that the well designed structures for better cooling & heating performance with high efficiency. And also it is performed that the system performance test of four types trial products for the use of hybrid commercial vehicle. System performance is affected by many component parts, especially heat sink design & power control method. It is applied that dual extrusive fin tube with buffer zone for the effective radiating of circulating liquid in tube. And also it is applied that power supply method with constant-current system. It is attained that system cooling capacity is 1.2kW, COP is 0.95.

• 센서학회지
• /
• 제13권2호
• /
• pp.139-143
• /
• 2004

This paper presents a method that the engine oil condition is detected using a natural convection heat transfer in a engine oil. A sensor circuit maintains a constant temperature difference between a heat plate and engine oil for detecting a natural convection heat transfer rate on the constant temperature. The natural convection heat transfer rate is measured by a current through the heat plate of the sensor circuit. The sensor is tested by a fresh oil. 6,000 km and 10,000 km driven oil in the oil temperature range from $20^{\circ}C$ to $100^{\circ}C$. In the experimental result, when the current through the heat plate is altered by variation of a engine oil temperature and flows driven oil more than fresh oil, the sensor could inform a engine oil deterioration to a car driver.

• 산업기술연구
• /
• 제32권A호
• /
• pp.103-107
• /
• 2012

Due to improvement of the semiconductor technology, the LED replaces the conventional lighting source and LED drivers have been studied and developed. The LED is driven by the constant current control method according to its characteristics. For the constant current control method, the linear regulator and the switching regulator is used. The switching regulator is usually used to LED drivers because it has specific characteristics as the wide input dynamic range and the high efficiency. In this paper, we have described the principle and the implement of the switching regulator, using the drive IC and the low cost DSP chip. Also, both methods have been implemented and its electrical characteristics had almost same experimental results in the steady state and the transient state.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.347-349
• /
• 1999

We have fabricated insulating thin films using p-hexadecoxyphenol(p-Hp) that was formed phenol-formaldehyde resin of crosslinked structure from reaction with formaldehyde by LB technique. For fabricated MIM device, the possibility for insulating layers of electronic were investigated by electrical properties of their LB films according to crosslinking of LB films current-voltage (I-V) properties and frequency-capacitance (C-F) characteristics. We have provided evidence for the high insulating performance of phenol-formaldehyde thin films by the LB method. Conductivity of their LB films was as follows: pure water > 1 % aq. Formaldehyde > heat treatment, in the current-voltage (I-V) characteristics. It is demonstrated that insulation properties of crosslinked p-HP LB films were improved. In capacitance-frequency properties, the heat-treated p-HP LB films for crosslinking showed a low relative dielectric constant.

• Corrosion Science and Technology
• /
• 제12권6호
• /
• pp.288-294
• /
• 2013

When the automotive body enters an electrocoating tank while applying an electric current, its steel surface is exposed to a very low induced current. Consequently, surface defects of coating may arise if the steel surface has lack of electric uniformity due to local defects such as local oxide. In this study, we investigated the preceding assessment methods to evaluate steel susceptibility of the low induced current during electrocoating before mass production. Prior to general electrocoating, we applied low constant voltage such as 3V or low constant current densities such as $0.35mA/cm^2$ and $0.50mA/cm^2$. In result, we confirmed that such methods were efficient for assessing steel susceptibility of low induce current during electrocoating.

• 한국전자통신학회논문지
• /
• 제17권1호
• /
• pp.71-76
• /
• 2022

밝기가 동작 전류에 비례하는 LED 조명은 다수의 LED를 직렬 연결하여 정전류원으로 구동하는 방식을 널리 사용하고 있다. 이러한 방식에서는 일부 LED가 고장으로 개방되면 전류 통로가 끊어져 직렬 연결된 모든 LED가 꺼지게 된다. 본 논문에서는 LED 동작 전압보다 약 0.4V 정도 높은 항복전압을 갖는 제너 다이오드를 개별 LED와 병렬로 연결하여 LED 고장 시 전류 우회로를 확보하므로 이러한 문제점을 해결하는 회로를 설계하였다. 시뮬레이션과 실험을 통해 LED 정상 동작 시에는 제너 다이오드로 전류가 거의 흐리지 않고, LED 고장 시에는 제너 다이오드가 안정적으로 전류 우회로로 동작함을 확인하였다.

• 태양에너지
• /
• 제20권1호
• /
• pp.97-108
• /
• 2000

The purpose of this study is to minimize the heat transfer surface area and cold fluid exit temperature of heat exchanger which applied to the refrigeration and air-conditioning system by utilizing the thermoelectric principle. Both uniform and non-uniform current distribution methods which applied to the analysis of the TE elements that incorporates heat exchanger were investigated. The non-uniform current distribution method had the better coefficient of performance and had the lower cold fluid exit temperature of the TE cooling system than the uniform current distribution method. It was found that if a TE cooling system incorporates a heat exchanger, a non-uniform current distribution should guarantee to the lowest cold fluid exit temperature. Also, the hybrid method (combination of the uniform and non-uniform current distribution method) is investigated to achieve the best results by combining the uniform and non-uniform current distributions. The results show that it can lower the cold fluid exit temperature and reduce the heat transfer surface area for the parallel flow arrangement if we apply the constant current in some entry region and the non-uniform increasing current in the direction of the cold fluid flow afterwards.

• 한국항행학회논문지
• /
• 제21권5호
• /
• pp.501-507
• /
• 2017

전자회로에서 부하가 제너다이오드일 경우, 입력전압에 의해 부하의 전류를 제어하고자 할 때 제너다이오드의 항복전압 특성에 따라 제어하고자 하는 출력전류가 변하기 때문에 기존의 전압제어 전류 생성 방법을 적용할 수 없다. 이 논문에서는 입력전압을 이용하여 정격치보다 큰 전류를 제너다이오드에 인가하여 부품의 수명시험을 할 때, 제너다이오드가 경년열화에 의하여 항복전압의 특성이 변하여 부하전압이 달라져도 이에 관계없이 동일한 전류를 낼 수 있는 회로를 개발하였다. 이 방법으로 구성된 회로를 실증하기 위해 각 블럭의 부품 값을 적용하고 시뮬레이션 하여 입력전압으로 출력전류를 선형적으로 제어하는 결과를 확인하였다. 결과에 의하면 우리가 측정하고자 하는 항복전압 이상의 입력전압에 대해서 출력전류가 선형적으로 변하며 제너다이오드의 경년열화에 의한 항복전압의 변화와 관계없이 일정한 전류가 흐르는 것을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.341-344
• /
• 1991

Current controlled pulse width modulation(PWM) for voltage source inverter(VSI) is one of the control method which controls the current directly so that we can perform vector control because it reduces the orders of differential equations of the induction machine. This paper propose a Fuzzy current controlled PWM which properly minimize a current ripple using Fuzzy theory in a constant switching frequency. This technique is applied to an electrical drive system with an induction machine(IM) by simulation. By comparison with the known classical method such as ramp comparison, hysteresis band method, our contribution shows the better performances.

• Journal of Power Electronics
• /
• 제13권2호
• /
• pp.250-255
• /
• 2013

This paper proposes an optimal current distribution method of dual-rotor brushless DC machines (DR-BLDCMs) which have inner and outer surface-mounted permanent-magnet rotors. The DR-BLDCM has high power density and high torque density compare to the conventional single rotor BLDCM. To drive the DR-BLDCM, dual 3-phase PWM inverters are required to excite the currents of a dual stator of the DR-BLDCM and an optimal current distribution algorithm is also needed to enhance the system efficiency. In this paper, the copper loss and the switching loss of a DR-BLDCM drive system are analyzed according to the motor parameters and the switching frequency. Moreover, the optimal current distribution method is proposed to minimize the total electrical loss. The validity of the proposed method was verified through several experiments.