• Journal of Plant Biology
• /
• v.35 no.3
• /
• pp.253-257
• /
• 1992

Potyvirus group is the largest group among plant virus groups and damages severely plant hosts upon infectiQn. In order to investigate the mechanism by which potyviruses induce disease in plants, a cDNA clone 29-6 which is cOIlsidered to be a cDNA clone for garlic mosaic virus (GMV) was isolated. It did not hybridize to garlic latent virus genome, which is one of two major garlic viruses. Northern blot analysis shows that the genome size of garlic mosaic virus was about 9 kb. Clone 29-6 strongly hybridizes to poly(A) RNA isolated from garlic leaves, suggesting that GMV RNA is polyadenylated as other potyviruses. Nucleotide sequence analysis of cDNA clones overlapping with clone 29-6 showed that garlic plants are infected with various strains of garlic mosaic virus which are closely related to each other. other.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.10
• /
• pp.843-852
• /
• 2016

The autorotative flight of maple seeds(Acer palmatum) is numerically simulated based on the 3D geometry and the motion parameters of real seeds. The nominal values of the motion parameters are 1.26 m/s for descent velocity, 133.6 rad/s (1,276 rpm) for spinning rate, $19.4^{\circ}$ for coning angle, and $-1.5^{\circ}$ for pitch angle. A compact leading-edge vortex (LEV) positioned at the inner span of the seed blade causes a large suction pressure on its leeward surface. The suction pressure peaks occur near the leading region of inner span sections. The flow pattern characterized by the prominent LEV and the values of aerodynamic force coefficients obtained in the present study are in good agreement with experimental data measured for a dynamically-scaled robot maple seeds. A spiraling vortex developed in the leeward region advances toward the seed tip and merges with the tip-passing flow, which is considered to be a mechanism of maintaining stable and attached LEV for the autorotating maple seeds.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.245-245
• /
• 2015

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. 특히 CIGS 태양전지에서는 Na의 역할이 매우 중요한데 유연기판의 경우 이러한 Na이 없을 뿐만 아니라 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 또한 플라스틱기판의 경우 내열성이 낮아 저온에서 공정을 진행해야하는 단점이 있다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 유연기판으로 STS 430 stainless steel과 poly-imide를 이용하여 특성 개선을 진행하였다. 먼저 stainless steel과 Poly-imide, soda-lime glass, coning glass의 기판을 이용하여 기판에 따른 흡수층의 특성을 비교 분석하였으며 stainless steel 기판을 이용하여 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 이때 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.6%로 증가하였다. 또한 poly-imide 기판을 이용하여 $400^{\circ}C$이하에서 흡수층을 제조하여 특성평가를 진행하였으며 소자 제조 후 효율은 약 12.2%를 달성하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.8
• /
• pp.631-638
• /
• 2018

In this paper, we propose a method to improve the performance by guidance technique and applying it to the precision guided ammunition. The proposed method is a technique designed to reduce the target error of ammunition by reducing the projectile error without analyzing the motion characteristics of the shot. This technique is applied to the moving average filter technique which is widely used as signal processing technique to reduce the fluctuation of the output of the inboard mounting inertial sensor caused by the rotation and the coning motion of the ammunition. In order to compare the performance of the applied technique including the simple 3D guided control technique and the proposed improvement technique. It is confirmed that the application of this technique improves the accuracy of impact of the cannon - launched ammunition with severe environmental conditions and irregular motion characteristics unlike the missile.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.51-59
• /
• 2007

The end-burning combustion field using impinging oxidizer injectors are analyzed with tangential type injectors in order to examine their mixing and combustion characteristics. The impinging type showed further improved mixing effect as well as the combustion efficiency compared to the previously studied tangential injector. A novel injector capable of delivering impinging and swirl effect is introduced in this study where it demonstrated that the grain coning effect can be avoided. It was found that the combined impinging and swirling flow would promote the radial mixing rate increasing the residence time and the turbulent intensity. However, the use of the step combustor which may augment the turbulent intensity did not show any notable difference compared to the basic combustor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.8
• /
• pp.653-660
• /
• 2017

In this paper, the author analyzes direction finding accuracy based on phase comparisons to estimate elevation and azimuth angles of arrival signals. This paper considers the uniform array configurations using four and three elements. In that direction finding structures, I present the analytic expressions for estimated elevation and azimuth angles and then analyze the direction finding errors. And one presents the design guideline of direction finding system in comparison with aspects of accuracy, structure, the number of channels in that structures. The analysis result is similar with simulation one and has difference within $1.2^{\circ}RMS$. From the proposed analysis results, one knows that when SNR is 20 dB and the baseline is half of wavelength, the estimated elevation accuracy of the uniform array using four elements is 1.15 times better than the one of the uniform array using three elements and the estimated azimuth accuracy is same each other. In addition, one knows coning error is eliminated in 2-D direction finding structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.3
• /
• pp.243-251
• /
• 2019

Recently, several studies were conducted on the micro-Doppler(MD) phenomenon to identify a warhead from decoys. Both, the warhead and decoy, can be modeled as various shapes and maneuver with their own micro-motion. Their MD phenomenon can be demonstrated by amplitude modulation and phase modulation. Most studies have utilized approximate solutions to express the amplitude modulation regardless of various warhead and decoy shapes. However, the exact solution of the amplitude modulation is required for more effective warhead identification. In this study, we proposed a new modeling method of receiving radar signals from warheads and decoys based on physical optics. The proposed solution was evaluated using an electromagnetic prediction technique and computer-aided design models.