• 한국광물학회지
• /
• 제18권2호
• /
• pp.83-92
• /
• 2005

광물의 용해속도는 기후에 따라 지역적인 차이는 있으나, 일반적으로 화강암을 구성하는 광물중 장석류의 풍화속도가 다른 광물에 비해 비교적 빠르기 때문에 파손 정도는 장석의 안정성에 지배된다. 지구화학적 반응 모델링 결과, 강우에 의해서 화강암이 변질되는데 걸리는 시간은 다른 변수를 고려하지 않고 pH만을 고려한 pH=4.5인 산성수내에서의 변질속도와 비교할 때 일반적인 빗물(pH=5.7)보다 약 2.3배 더 빠른 것으로 계산되었다. 이러한 결과는 화강암질 석조문화재의 보존에 있어서 pH가 중요한 요소로 작용할 수 있음을 의미한다. 석조문화재의 풍화를 억제하기 위해서는 암석의 풍화특성이 우선적으로 규명되어야 하며, 가수분해, 산 반응 등의 화학적 풍화작용은 물과의 접촉에 의해 이루어지므로 물을 차단하기 위하여 발수코팅, 오일코팅 또는 건조환경을 조성하는 방안을 고려해야 할 것이다. 세척제와 생물방제를 이용할 시는 빗물이나 화강암과의 장기적 반응을 고려하여 중성화작용과 환원성 환경이 형성될 수 있는 재질의 선택이 매우 중요하다.

• Fibers and Polymers
• /
• 제7권2호
• /
• pp.129-138
• /
• 2006

Using a strain-controlled rheometer, the steady shear flow properties of aqueous xanthan gum solutions of different concentrations were measured over a wide range of shear rates. In this article, both the shear rate and concentration dependencies of steady shear flow behavior are reported from the experimentally obtained data. The viscous behavior is quantitatively discussed using a well-known power law type flow equation with a special emphasis on its importance in industrial processing and actual usage. In addition, several inelastic-viscoplastic flow models including a yield stress parameter are employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models is also examined in detail. Finally, the elastic nature is explained with a brief comment on its practical significance. Main results obtained from this study can be summarized as follows: (1) Concentrated xanthan gum solutions exhibit a finite magnitude of yield stress. This may come from the fact that a large number of hydrogen bonds in the helix structure result in a stable configuration that can show a resistance to flow. (2) Concentrated xanthan gum solutions show a marked non-Newtonian shear-thinning behavior which is well described by a power law flow equation and may be interpreted in terms of the conformational status of the polymer molecules under the influence of shear flow. This rheological feature enhances sensory qualities in food, pharmaceutical, and cosmetic products and guarantees a high degree of mix ability, pumpability, and pourability during their processing and/or actual use. (3) The Herschel-Bulkley, Mizrahi-Berk, and Heinz-Casson models are all applicable and have equivalent ability to describe the steady shear flow behavior of concentrated xanthan gum solutions, whereas both the Bingham and Casson models do not give a good applicability. (4) Concentrated xanthan gum solutions exhibit a quite important elastic flow behavior which acts as a significant factor for many industrial applications such as food, pharmaceutical, and cosmetic manufacturing processes.

• Steel and Composite Structures
• /
• 제35권4호
• /
• pp.579-598
• /
• 2020

Consideration of the panel zone (PZ) deformations in the analysis of steel moment frames (SMFs) has a substantial effect on structural response. One way to include the PZ effect on the structural response is Krawinkler's PZ model, which is one of the best and conventional models. However, modeling of Krawinkler's PZ model has its complexity, and finding an alternative procedure for PZ modeling is of interest. In this study, an efficient model is proposed to simplify Krawinkler's PZ model into an Adjusted Rigid-End Zone (AREZ). In this way, the rigid-end-zone dimensions of the beam and column elements are defined through an appropriate rigid-end-zone factor. The dimensions of this region depend on the PZ stiffness, beam(s) and columns' specifications, and connection joint configuration. Thus, to obtain a relationship for the AREZ model, which yields the dimensions of the rigid-end zone, the story drift of an SMF with Krawinkler's PZ model is equalized with the story drift of the same structure with the AREZ model. Then, the degree of accuracy of the resulting relationship is examined in several connections of generic SMFs. Also, in order to demonstrate the applicability of the proposed model in SMFs, several SMFs ranging from 3- to 30-story representing low- to high-rise buildings are examined through linear static and dynamic time history analysis. Furthermore, non-linear dynamic analyses of three SMFs conducted to validate the degree of accuracy of the proposed model in the non-linear analysis of SMFs. Analytical results show that there is considerable conformity between inter-story drift ratio (IDR) results of the SMFs with Krawinkler's PZ model and those of the centerline SMFs with AREZ.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.38-45
• /
• 2004

This paper studies the effects of intake port configuration on the swirl that is key parameter in the flow field of direct injection diesel engines. In-cylinder flow characteristics is known to have significant effects on fuel air mixing, combustion and emissions. To investigate the swirl flow generated by various intake ports, steady state flow tests were conducted to evaluate the swirl. Helical port geometry, SCV shape and bypass were selected as the design parameters to increase the swirl flow and parametric study was performed to choose the optimal port shape that would generate a high swirl ratio efficiently. The results revealed that a key factor in generating a high swirl ratio was to suitably control the direction of the intake air flow passing through the valve seat. For these purposes, we changed the distance of helical and tangential port as well as installed bypass near the valve seat and the effects of intake port geometry on in-cylinder flow field were visualized by a laser sheet visualization method. From the experimental results, we found that the swirl ratio and mass flow rate had a trade off relation. In addition, the result indicates that the bypass is a effective method to increase the swirl ratio without sacrificing mass flow rate.

• 대한한방부인과학회지
• /
• 제18권4호
• /
• pp.24-35
• /
• 2005

Purpose : This study was conducted to investigate the effects of Cynomorii Herba (鎖陽) on　the reproductive competence in male mice.　Methods ：　We used 8-week-old Spraque-Dawley rats and administered the extract powder of Cynomorii Herba to 5 rats and normal saline to control group once in a day for 28 days. Then we observed the changes of body weight before and after administration of Cynomorii Herba extracts and normal saline. We isolated their testis surgically and observed the weight of testis, epididymis, vascular gland and prostate. Also we examined the total, normal and motile sperm concentration, the concentration of testicular catalase, peroxidase and configuration of testicular tissue before and after administration of Cynomorii Herba extracts and normal saline. Results : We found that the concentration of total, normal, motile sperm in testis of Cynomorii Herba treated group shows significant difference compared with the control group. The body weight, the weight of testis, epididymis and the concentration of testicular catalase and peroxidase were higher in the Cynomorii Herba treated group, on the other hand the weight of vascular gland was lower in the Cynomorii Herba. But the contents of above statement showed no significant difference. The weight of　prostate showed lower in the control group statistically than that of the Cynomorii Herba treated group. We observed the seminiferous tubules taken shape minutely and the number of normal sperm increased in Cynomorii Herba treated group's testicular tissue. Conclusion This study shows that Cynomorii Herba may have an effect on the concentration, morphology and motility of sperm, the important factor in male fertility.

• 한국전자파학회논문지
• /
• 제21권12호
• /
• pp.1412-1422
• /
• 2010

펄스 체이싱을 이용한 바이스태틱 레이더는 탐지 영역을 효과적으로 스캔하기 위해 수신 빔을 이용하여 송신 펄스를 추적함으로써 표적을 탐지한다. 수신 빔을 이용한 펄스 추적시 펄스-펄스간 빔 포인팅 오차에 의해 수신 펄스의 타이밍 오차와 신호 세기의 변화가 발생할 수 있다. 본 논문에서는 수신 빔 포인팅 오차에 의해 발생된 에러가 MTI 필터의 성능을 제한할 수 있음을 제안하였고, 바이스태틱 구조만의 고유한 특성인 기하학적 요소와 MTI 성능의 관계식을 유도하였다. 시뮬레이션을 통해 수신 빔 조향 오차에 의한 개선 성능 제한을 고찰하였고, 수신 빔의 조향 오차를 0.5도 이하로 유지함으로써 성능 개선에 기여할 수 있음을 확인하였다.

• 대한간호학회지
• /
• 제46권1호
• /
• pp.149-158
• /
• 2016

Purpose: This study was done to develop of the Korean intensive care delirium screening tool (KICDST). Methods: The KICDST was developed in 5 steps: Configuration of conceptual frame, development of preliminary tool, pilot study, reliability and validity test, development of final KICDST. Reliability tests were done using degree of agreement between evaluators and internal consistency. For validity tests, CVI (Content Validity Index), ROC (Receiver Operating Characteristics) analysis, known group technique and factor analysis were used. Results: In the reliability test, the degree of agreement between evaluators showed .80~1.00 and the internal consistency was KR-20=.84. The CVI was .83~1.00. In ROC analysis, the AUC (Area Under the ROC Curve) was .98. Assessment score was 4 points. The values for sensitivity, specificity, correct classification rate, positive predictive value, and negative predictive value were found to be 95.0%, 93.7%, 94.4%, 95.0% and 93.7%, respectively. In the known group technique, the average delirium screening tool score of the non-delirium group was $1.25{\pm}0.99$ while that of delirium group was $5.07{\pm}1.89$ (t= - 16.33, p <.001). The factors were classified into 3 factors (cognitive change, symptom fluctuation, psychomotor retardation), which explained 67.4% of total variance. Conclusion: Findings show that the KICDST has high sensitivity and specificity. Therefore, this screening tool is recommended for early identification of delirium in intensive care patients.

• International Journal of Concrete Structures and Materials
• /
• 제11권1호
• /
• pp.85-97
• /
• 2017

Research has suggested that conventional lightweight concrete can offer durability advantages due to reduced cracking tendency. Although a number of publications exist providing the results of laboratory-based studies on the durability performance of lightweight concrete (with lightweight coarse aggregate) and internally cured concrete (using prewetted lightweight fine aggregate), far fewer field studies of durability performance of conventional lightweight concrete bridge decks in service have been performed. This study was commissioned to provide insight to a highway agency on whether enhanced durability performance, and therefore reduced maintenance and longer lifecycles, could be anticipated from existing lightweight concrete bridge decks that were not intentionally internally cured. To facilitate performance comparison, each lightweight bridge deck selected for inclusion in this study was paired with a companion normalweight bridge deck on a bridge of similar structural type, deck thickness, and geometric configuration, with similar age, traffic, and environmental exposure. The field-observed cracking of the decks was recorded and evaluated, and crack densities for transverse, longitudinal, and pattern cracking of the normalweight and lightweight deck in each pair were compared. Although some trends linking crack prevalence to geographic location, traffic, and age were observed, a distinct difference between the cracking present in the paired lightweight and normalweight bridge decks included in this study was not readily evident. Statistical analysis using analysis of covariance (ANCOVA) to adjust for age and traffic influence did not indicate that the type of concrete deck (lightweight or normalweight) is a statistically significant factor in the observed cracking. Therefore, for these service environments, lightweight decks did not consistently demonstrate reduced cracking.

• 한국항해학회지
• /
• 제10권2호
• /
• pp.97-114
• /
• 1986

Ship's maneuverability is very important factor in safe ship handling and economical ship operation. Steering characteristics are consisted of course stability and maneuverability. Today in many advanced ship-building countries, they study ship's course stability, using model ship tests, such as straight line tests, rotating arm tests and Planar Motion Mechanism (PMM) etc., in tow in tanks. It is the purpose of this paper to provide ship's handlers with better understanding of steering characteristics and to help them in safe controlling and manevering . In this paper, the author simulated response of various vessels, running straight course with constant speed, and they are disturbed by small external disturbance of one degree yaw angle with no angular velocity . The author used the hydrodynamic derivtives resulted at tests of Davidson's laboratory in Stevens Institute of Technology, New Jersey, U.S.A. Course stability was evaluated and analyzed in various respects, such as block coefficient, ratio of ship's length to beam, draft and rudder area ratio etc. The obtained results are as follows : (1) The ship's course stability is affected by magnitude of block coefficient greatly. In case that the block coefficient is more than 0.7, the deviation varies at nearly same rate but the requistite time to reach the steady course is different. (2) The ship's course stability is affected by magnitude of L/B. When the dimensionless time reaches about 3, the deviation and requisite time to reach the steady course are influenced nearly same. After the dimensionless time is about 3, they change on invariable ratio. (3) The effect to course stability by L/T and RA' can be neglected. (4) The reason why thy VLCC and container feeder vessel are unstable on their course is that their block coefficient is generally more than 0.8 and the ratio of ship's length to beam is about 6.0.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.667-670
• /
• 2007

A new series of highly bright and efficient poly(pphenylenevinylene) s (PPV)s based on polyhedral oligomeric silsesquioxanes (POSSs) was synthesized via the Gilch polymerization method. The three POSScontaining PPVs are as follows: POSS05- PPV(containing 5 mol % POSS-appended PPV units), POSS25-PPV(containing 25 mol % POSS-appended PPV units), and POSS100-PPV(containing 100 mol % POSS-appended PPV units; this is the first ${\pi}-conjugated$ polymer composed of 100 mol % POSSsappended repeating units). The POSS-containing PPVs exhibit higher glass transition temperatures $(64-77^{\circ}C)$ than that of MEH-PPV $(58^{\circ}C)$, indicating that electroluminescence (EL) devices fabricated with these polymers should have good thermal stabilities. Light-emitting diodes (LEDs) with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al were fabricated using the novel POSS-containing PPVs. Surprisingly, the luminescence efficiency (0.48 cd/A at $10540\;cd/m^2$) of the binary blend consisting 5 wt % of POSS25-PPV and 95 wt % of MEH-PPV was found to be enhanced by a factor of 6.4 with a maximum brightness of $11010cd/m^2$ (at 14.3 V).