• Proceedings of the IEEK Conference
• /
• 2000.06a
• /
• pp.244-247
• /
• 2000

This paper deals with methods for partial response maximum-likelihood (PRML) detection and crosstalk cancellation. In accrodance with the demand for increased recording density, 20 gigabyte (Gbyte) digital versatile disk (DVD) ROM channel is considered. Channel is modelled to be close to real optical channel using DIFFRACT$\^$TM/. After comparing the spectral characteristics of various PR polynomials, P(D)=1＋D＋D$^2$＋D$^3$is proposed as a target PR. The performance of the system is illustrated under the condition that the readout signal is degraded by crosstalk, radial tilt and nonlinear distortions in optics. The experimental results show that crosstalk and nonlinear distortions degrade performance by about 2dB, respectively. We also show that when radial tilt is added to the crosstalk, the performance degradation assumes quite significant proprotions.

• Proceedings of the KSPS conference
• /
• 2002.11a
• /
• pp.205-208
• /
• 2002

Bimodal speech recognition based on lip reading has been studied as a representative method of speech recognition under noisy environments. There are three integration methods of speech and lip modalities as like direct identification, separate identification and dominant recording. In this paper we evaluate the robustness of lip reading methods under the assumption that lip parameters are estimated with errors. We show that the dominant recording approach is more robust than other methods with lip reading experiments. Also, a measure of lip parameter degradation is proposed. This measure can be used in the determination of weighting values of video information.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04c
• /
• pp.106-110
• /
• 2008

Continuous on-line temperature monitoring allows corrective measures to be taken to prevent upcoming failure. Continuous temperature monitoring and event recording provides information on the energized equipment's response to normal and emergency conditions. On-line temperature monitoring helps to coordinate equipment specifications and ratings, determine the real limits of the monitored equipment and optimize facility operations. Using wireless technique eliminates any need for special cables and wires with lower installation costs if compared to other types of online condition monitoring equipment. In addition, wireless temperature monitoring works well under difficult conditions in strategically important locations. Wireless technology for on-line condition monitoring of energized equipment is applicable both as standalone system and with an interface with power quality monitoring system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.582-587
• /
• 2002

Current information storage devices, such as HDD, CD/DVD-ROM/RW, probe-based memory and hologram memory, are compared with biological information storage mechanisms in DNA and brain memory. Newly developed approaches to overcome the limit of storage capacity are introduced in both magnetic and optical recording devices. Linear and areal density of information stored in the biological and mechanical storages are compared for the applications and developments of new storage devices.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.837-842
• /
• 2007

Information storage devices using disks have a disk vibration at the frequency which is equivalent to the disk rotational speed. They also have a track vibration due to the disk eccentricity at the same frequency. In near field recording systems, the former affects the air-gap servo and the latter affects the tracking servo. In this paper, we introduce a novel control algorithm based on the internal model principle to both servos. A controller block designed by the principle is connected to the base lead-lag type compensator in parallel in order to cancel the repeatable run-out due to the disk vibration or eccentricity. Simulation and practical application of the algorithm on a near field recording system show good servo performance.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.2142-2143
• /
• 2006

Today any data storage system cannot satisfy all of these conditions, however holographic data storage system can perform faster data transfer rate because it is a page oriented memory system using volume hologram in writing and retrieving data. System can be constructed without mechanically actuating part therefore fast data transfer rate and high storage capacity about 1Tb/cm3 can be realized. In this research, to reduce errors of binary data stored in holographic data storage system, a new method for bit error reduction is suggested. Firstly, find fuzzy rule to use test bed system for Element of Holographic Digital Data System. Secondly, make fuzzy rule table using DNA coding method. Finally, reduce prior error element and recording digital data. Recording ratio and reconstruction ratio show good performance.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.922-924
• /
• 1998

In this paper, an optical fiber sensor(OF sensor) utilizing the principal of Mach-Zehnder interferometer were proposed to detect the partial discharge signals in insulating oil. At first the AC breakdown signals were detected to check the response of the OF sensor. The detected signals from OF sensor was consistent with that from current probe. After the response checking, simultaneous measurements and continuous recording were made of electrical and the OF sensor signals from partial discharge(PD) produced by IEC(b) electrode system immersed in insulating oil. The continuous recording made it possible to extract basic quantities of PD from the OF sensor signals, such as pulse phase and pulse amplitude distribution. Through the signal analysis, the absolute peaks of the OF sensor PD signal was found to be increased with the amplitude of electrical signals, and these results mean that there is a strong correlation between OF sensor and electrical PD signals. It was demonstrated that the OF sensor in this research had a possibility to detect the PD signals in power apparatus.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.589-594
• /
• 2002

In manufacturing of welded parts which require a proof on acceptance close observation of the process is mandatory. The manufacturer is obliged to document the welding process. An approach for monitoring and recording the process of laser beam welding combining theoretical knowledge, process monitoring and welding experience will be presented. The range of application of a device for co-axial process monitoring was extended up to 20 mm sheet thickness welded in one pass at beam powers of up to 20 kW. Crucial features of the process which refer to the formation of failures were observed. The results presented give rise to the general applicability of the approach for process monitoring and recording as well as failure management.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.718-721
• /
• 2001

For higher recording density in optical data storage, near field optics is being actively researched as one of the promising alternatives. But the tight assembling tolerance in NFR is one of big barriers to overcome for the realization of it. In this paper, the tolerances in assembling optic components of NFR system are analyzed. Some of key tolerances can be loosened by the optimization of objective lens design. But one of them become too tight by the optimization and should be controlled by other means. One of possible methods to control the tolerance is discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.378.1-378
• /
• 2002

DVD, HD(High Density)-DVD등의 고밀도 광 디스크의 광 기록재생장치는 고 개구율(Numerical Aperature)의 대물렌즈로 집광 빔의 크기를 소형화하여 기록용량을 증대시키고 있다. 이 경우 광축과 광 디스크의 기록면에 대한 경사는 광학적인 수차가 발생되어 신호 레벨의 저하나 기록시의 피트(pit) 형성의 오류, Crosstalk등의 문제가 발생한다. 이를 극복하기 위해 직접 디스크의 경사에 따라 제어할 수 있는 픽업 구동기가 제안되어 왔지만 주로 Half Height(12.7mm)에 사용되는 틸트 구동기였으며 Slim(6.3mm)형 틸트 구동기는 제안되지 못하였다. (중략)