• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.350-354
• /
• 2020

In this study, a pressure sensor for each displacement was fabricated based on the silicon-based pressure sensor obtained through simulation results. Wires were bonded to the pressure sensor, and a piezoresistive pressure sensor was inserted into the printed circuit board (PCB) base by directly connecting a micro-electro-mechanical system (MEMS) sensor and a readout integrated circuit (ROIC) for signal processing. In addition, to prevent exposure, a non-conductive liquid silicone was injected into the sensor and the entire ROIC using a pipette. The packaging proceeded to block from the outside. Performing such packaging, comparing simple contact with strong contact, and confirming that the measured pulse wavelength appears accurately.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.1039-1042
• /
• 2001

A method for designing antireflection (AR) and antistatic (AS) films by the use of conducting polymer as an electrically conductive transparent layer is proposed. The conducting AR film is composed of four-layer with alternating high and low refractive index layer: silicon dioxide (n=1.44) and titanium dioxide (n=2.02) prepared at low temperature by sol-gel method are used as the low and high refractive index layer, respectively. The 3,4-polyethylenedioxythiophene (PEDOT) which has the sheet resistance of 10$^4$$\Omega$/$\square$ is used as a conductive layer. Optical constant of ARAS film was measured by the spectroscopic ellipsometer and from the measured optical constants the spectral properties such as reflectance and transmittance were simulated in the visible region. The reflectance of ARAS films on glass substrate was below 0.8 %R and the transmittance was higher than 95 % in the visible wavelength (400-700 nm). The measured AR spectral properties was very similar to its simulated results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.802-805
• /
• 2001

Conductive polymer is insulator or semiconductor in initial state. Polyaniline(PANI) is a $\pi$-conjugated polymer that shows electric property changes, when it is contact with oxidant/reductor chemicals. Synthesis of polyaniline is used vacuum evaporation method, using by (NH$_4$)$_2$O$_{8}$과 NMP, NH$_2$NH$_2$, HCl, MH$_4$OH, etc. Doped PANI is used such a resistor, addition to graphite is increased conductivity. Applying contact voltage, samples show constant current and contact temperature.e.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.91-92
• /
• 2006

Aluminum-doped zinc oxide (AZO) films are attractive materials as transparent conductive electrode because they are inexpensive, nontoxic and abundant element compared with indium tin oxide (ITO). AZO films have been deposited on glass (corning 1737) substrates by RF magnetron sputtering system. The electrical resistivity of AZO films was $1.81{\times}10^{-2}{\Omega}cm$ and the average transmittance in the visible range 400-800 nm was more than 76% Organic light-emitting diodes (OLEDs) with AZO/TPD/$Alq_3$/Al configuration were fabricated. The current density-voltage properties of devices were studied and compared with ITO devices fabricated under the same conditions.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.250-254
• /
• 2008

Eddy currents are induced when a nonmagnetic conductive material is moving subjected to the magnetic field due to a permanent magnet. These currents circulates in the conductive material and are dissipated, causing a repulsive force between the magnet and the conductor. Using this concept, the eddy current damping can be used as a viscous damping. The present study investigates the characteristics of a magnetic damping analytically and experimentally. The theoretical model of a eddy current damping is developed from electromagnetics and is verified from experiments. The drop test of a magnet in the cooper tube shows that the present model can accurately predict the damping force. Additionally, the dynamic test of a eddy current damping is carried to verify the present model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.391-394
• /
• 2002

Transparent conductive oxides (TCO) are necessary as front electrode for most thin film solar cell. In our paper, transparent conducting aluminum-doped Zinc oxide films (ZnO:Al) were prepared by rf magnetron sputtering on glass (Corning 1737) substrate as a variation of the deposition condition. After deposition, the smooth ZnO:Al films were etched in diluted HCl (0.5%) to examine the electrical and surface morphology Properties as a variation of the time. The most important deposition condition of surface-textured ZnO films by chemical etching is the processing pressure and the substrate temperature. In low pressures (0.9 mTorr) and high substrate temperatures ($\leq$30$0^{\circ}C$), the surface morphology of films exhibits a more dense and compact film structure with effective light-trapping to apply the silicon thin film solar cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.331-331
• /
• 2008

Transparent conductive oxide (TCO) are necessary as front electrode or anti-reflecting coating for increasing efficiency of LED and Photodiode. In this paper, aluminum-doped Zinc oxide films(AZO) were prepared by RF magnetron sputtering on Si substrate at room temperature with application of substrate bias from -60 to 60 V. Then annealed at temperature of 200, 300 and $400^{\circ}C$ for 1hr in $H_2$ ambient. Structural and electrical property of AZO thin films were investigated.

• Journal of The Korean Astronomical Society
• /
• v.29 no.spc1
• /
• pp.339-340
• /
• 1996

In the present study we examine physical characteristics of a thin and rigid magnetic flux tube with a steady flow inside, which is embedded vertically upward in the solar atmosphere. We found from this study that (1) The downward material flow gives rise to a dominant heating in the flux tube which works with the conductive heating in the same direction. However, the upflow flow creates a dominant cooling which works against the conductive heating, resulting in a steeper temperature gradient with a shallower transition region. (2) Since the thickness of the transition region determines the material content in the transition region, a broader transition region of the downflow tube produces a larger differential measure.

• Coupled systems mechanics
• /
• v.9 no.5
• /
• pp.397-410
• /
• 2020

The present investigation is concerned with two-dimensional deformation in a homogeneous isotropic non local thermoelastic solid with two temperatures due to thermomechanical sources. The theory of memory dependent derivatives has been used for the study. The bounding surface is subjected to concentrated and distributed sources (mechanical and thermal sources). The Laplace and Fourier transforms have been used for obtaining the solution to the problem in the transformed domain. The analytical expressions for displacement components, stress components and conductive temperature are obtained in the transformed domain. For obtaining the results in the physical domain, numerical inversion technique has been applied. Numerical simulated results have been depicted graphically for explaining the effects of nonlocal parameter on the components of displacements, stresses and conductive temperature. Some special cases have also been deduced from the present study. The results obtained in the investigation should be useful for new material designers, researchers and physicists working in the field of nonlocal material sciences.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1034-1037
• /
• 1999

In this paper, we analyze the inductive interference in conductive material around power transmission line. To compute induced eddy currents as well as electromagnetic fields, finite element method(FEM) is used for numerical calculation. The characteristics of conductive material such as gas pipeline, overhead guide wires, conducting earth and so on are taken account of FEM analysis. This research also shows that mitigation wire reduces amount of eddy current in buried gas pipe line.