• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.427-430
• /
• 2005

The purpose of this study is to choose the right chemical admixture to reduce slump loss of lightweight aggregate concrete. So we compare 3 types of chemical admixture as measuring slump loss from mixing to 60 minutes. The lightweight aggregate of this study is made by clayt and dust from lots of industry. To save natures, we will use many types of industrial wastes and try to spend much making artificial aggregate.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.227-228
• /
• 2009

This study proceeded to find the optimum mixing rate of a high strength concrete with 80MPa of the contribution and composite effect on the resistance to fire of the fibers were analyzed and the corresponding results were exploited to derive practical mix proportions. Also proceeded to propriety examination of limit value for optimum operating condition.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.273-276
• /
• 2003

The non-evaporable water and calcium hydroxides were measured by TG/DTA for studying the temperature effect on hydration of concrete mixture. The experimental parameters introduced in this study were the curing temperatures, ages and W/C ratios. The mixing temperature was also controlled to improve the efficiency of experimental work. While the mixture cured at high temperature showed the large quantity of non-evaporable water and calcium hydroxides at early age, the production rate of these hydration products was decreased as increasing the curing age, and the quantity of hydration product became smaller than that of the corresponding mixture cured at lower temperature at later age.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.124-127
• /
• 2003

Sewage sludge and clay used as raw materials in the study. Green aggregates contain different contents by dried weight of the sewage sludge, up to 80 percent is manufactured and burning conditions of soak temperature, soak time and rate of temperature increase. influence of burning condition and mixing ratio on specific gravity of burned aggregate are discussed. The appropriate burning condition to all aggregates is evaluated. Aggregates result form the thermal treatment get specific gravity under 0.8, water absorption fewer than 7.5 percent, and aggregate crushing value from 28 to 53. As the result, aggregates can be available as the lightweight aggregate for non-structural concrete.

• Computers and Concrete
• /
• v.19 no.5
• /
• pp.451-455
• /
• 2017

Technological advancements in the field of building materials are achieved day by day. In this study, a new lightweight concrete aggregate is produced by mixing certain rates of colemanite (0%, 7.5%, 12.5%, 17.5%), cement and coating the surface of pumice aggregate with this mixture. Thin aggregate sections are analyzed with specific gravity, unit weight, water absorption, impact, and crushing experiments. In this way, the production of cement and cement+colemanite coated lightweight concrete aggregates is investigated and an opinion on the likely behavior of these concrete types is provided.

• Journal of Industrial Technology
• /
• v.21 no.A
• /
• pp.285-292
• /
• 2001

The amount used of aggregates for concrete is increasing rapidly since the mid-1980s in Korea. The natural gravels from river are already displaced with crushed stone, and use of crushed sand as a substitute of natural river sands, also, is getting increased day by day. This paper is presented for mixture of high strength concrete using crushed sands. Mixing design of concretes are various water-cement ratios(w/c) such as 25%, 40%, 55% and different replacement ratio of crushed sands to natural sands such as 0%, 20%, 40%, 60%. As a results, it has been shown that compressive strength of concretes with w/c lower than 40% and 25% is higher than $400kgf/cm^2$ and $600kgf/cm^2$ respectively.

• Journal of Industrial Technology
• /
• v.16
• /
• pp.105-112
• /
• 1996

This paper presents coal mine waste (CMW) for use in concrete manufacture as a replacement of normal aggregates. The CMW in this study was collected from Sabook, Jungson-kun, Kangwon-do. Fine and coarse asggregates from CMW were prepared by crushing it in a jaw crusher and separating debris with #4 sieve. CMW aggregates showed good physical and mechanical properties with having specific gravity over 2.65, absorption less than 1%, and abration ratio below 20%, but particle shape of CMW was long or flat, which caused a poor workability in mixing. Therefore, to make workability better, a 1/4 of CMW coarse aggregate was replaced with normal aggregate which had a good particle shape, and a superplasticizer was added to the mix. Compressive strength and other mechanical properties of CMW concrete was very good. In conclusion, characteristics of CMW concrete was acceptable for use as a concrete structural material.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.2 s.16
• /
• pp.139-146
• /
• 2005

As a result of compressive strength, specimens having mixture rate of cockle shells of $15\%\;and\;20\%$ showed more increases of compressive strength than non-mixture specimens as age increases. Ductility capacity of specimens was higher in specimens mixing cockle shells than in specimens using general fine aggregates and specimen of $10\%$ of cockle shells was highest in ductility capacity. To sum up all experimental results, ductility capacity of specimen without shear reinforcement using mixture of cockle shell was higher than non-mixture specimen and it is considered that mixture of cockle shells up to $20\%$ as fine aggregate for concrete will be available. Continuous researches on durability, workability and economy of crushed cockle shells used for substitute fine aggregate of concrete will be needed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.5-6
• /
• 2017

Ultra high-strength concrete can prevent spalling by mixed ratio of PP and NY fiber. However, there is a lack of research on the deterioration of strength due to changes in mechanical properties after spalling prevention. In this study, the effect of high temperature on the mechanical properties of 150MPa concrete mixed with PP and NY fiber was evaluated. As a result, mixing PP and NY fiber is judge to be little effect on the mechanical properties of the 150MPa concrete at high temperature.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.687-694
• /
• 2013

This study was performed with an aim to improve the early-age strength of concrete containing fly ash, which is known to increase the long-age strength of concrete, reduce drying shrinkage, and enhance water tightness. The composition was partially substituted with calcium sulfoaluminate (CSA), from which ettringite is actively produced, in the early stages of hydration to verify its effect on improving the early-age strength and to determine the optimal mixing ratio. For this purpose, up to 30 % of the cement weight was substituted with fly ash, and the amount of CSA substitution was 8% of the fly ash weight. The mixtures were then fabricated into concrete specimens for compressive strength measurement and analysis of the correlation between the hydration products and the compressive strength.