• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.257-262
• /
• 2001

There are only a few tests to ensure concrete quality before placing in domestic situ; One is slump test for workability, the other is air content test for durability, the concrete compressive strength which is one of important factors to influence on concrete Quality has been tested after 28 days placing. Methods on early judgement of concrete strength have been introduced for concrete quality management, but such methods are time consuming, expensive, and required special expertise. Therefore, these have difficulty in situ application for concrete management. This study aimed at reviewing application of estimated equation of compressive strength as means for ready-mixed concrete, making an estimated equation which enables to estimate 28 days compressive strength by using regression formula analysis on basis of mixing designs of ready mixed concrete and results of compressive strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.681-686
• /
• 2001

The purpose of this study is to provide the optimum mix design of concrete to be placed at the face slab concrete in CFRD(Concrete Faced Rockfill Dam) for pumped storage power plants. The basic performance tests including compressive strength, modulus of elasticity, flexural strength and the control properties of crack including plastic shrinkage, drying shrinkage were conducted for concrete using fly ash and polypropylene fiber. From this study, the fly ash concrete represented the better results in the aspects of basic performance, control properties of crack and economy than ordinary portland cement concrete. Especially the concrete mix design containing 20% of fly ash is recommended to be applied in the construction of the face slab concrete in CFRD for pumped storage power plants.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.85-88
• /
• 2001

Utilization of demolished-concrete as recycled aggregate has been researched for the purpose of substituing for insufficient natural aggregate, saving resources and protecting environment. There, however, are some problems that qualities of recycled aggregates are not only largely diverse, but also mechanical properties of recycled aggregate concrete decrease a little in comparison with those of natural aggregate concrete. In this study, the resistance to freezing and thawing of recycled aggregate concrete was highly different due to adhered mortar on recycled aggregate, and durability factor of concrete with NA SRA and DRA was decreased more than that of control concrete. However, durability factor of concrete with AA SRA was larger than that of control concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.8-13
• /
• 1995

High strength ready-miced concrete with delivering time of about 90 minutes is successfully produced at ready-mixed concrete plant and placed columns and retaining walls of a tall building without any problems. The design strength of the concrete is 450 kgf/$\textrm{cm}^2$ and the required average compressive strength is 540 kgf/$\textrm{cm}^2$ according to ACI 363R-84 report with assumed coefficient of variation of 12% For the producing of good quality concrete, many laboratary and field tests are carried out. As the results of this study, the slump loss of high strength concrete is largely influenced by kinds of superplasticizer. The measured pump pressure of high strength concrete with slump of 22cm is higher than that of normal strength concrete with slump of 18cm by about 20~30% The measured average 28-day compressive strength of the concrete is 551 kgf/$\textrm{cm}^2$ and the coefficient of variation is 2.3%

• Proceedings of the Korea Concrete Institute Conference
• /
• 1989.10a
• /
• pp.15-20
• /
• 1989

The effect of superplasticizing agents on the sorkability performance in fresh concrete have been analyzed and investigated under various mix proportions of water cement ratio of 0.40, 0.50, 0.60 and 0.70, superplasticizing agents of NL-4000 and Rheobuild-716, and addition rate of sp. agents of 0.0, 0.5, 1.0, 1.5 and 2.0 in the practical range. It is the aim of this study to provide the fundamental data on the fluidity performance and workability improvement of superplasticized concrete such as time-dependent change of slump, flow value and compacting factor, air content, bleeding, mixing temperature and setting rate of fresh concrete comparing with base concrete and conventional concrete for the practical use and research data accumulation of superplasticized concrete in the side of development of concrete construction technology and management.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1991.04a
• /
• pp.29-32
• /
• 1991

This is the study on the performance of workability and engneering properties of flowing concrete using the superplasticizers, which are being used for control of the consistency of fresh concrete without modifying the properties of the hardened concrete and for production of high quality concrete at a low water-cement ratio. It is the aim of this study to analyze and investigate workability and engineering properties of flowing concrete according to the addition rate in poor and rich mix proportions of base concrete. Base on this fundamental investigation for the development of flowing concrete mix design, it could be drawn that the workability and engineering properties of flowing concreteare influenced greatly by mix proportion and dosage of superplasticizers.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.507-512
• /
• 2002

Prestressed concrete I-girders were used in the bridge applications in the early 1950s. During the last four decades, the most widely used girder length of bridges have been below 30 meters. The main objective of this study is to develope the alternative section for widely spaced girder of 30 meters span bridge. Girder spacing, the number of strands and compressive strength of concrete are major parameters for widely spaced girders. The optimal girder spacing is determined through the parameter studies of design using widely spaced girders. 30m span bridges of widely girder spacing must use high-strength concrete. Although the basic unit cost of concrete is higher for high-strength concrete, it may be partially or even fully offset by reduced quantities of concrete as result of the smaller number of girders used. High-strength concrete girders have more prestressing strands per girder, but the total number of strands for all of the girders is less than that required for the larger number of normal-strength concrete girders. It could design PSC-I Birdge with widely spaced girder owing to high-strength concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.991-996
• /
• 2002

In this study, there are kind of property experiments like fluidity, compressive strength, bleeding measurement, concrete sink for CFT use high fluidity concrete. The property difference between before transmit and after transmit concrete in the mock up test with ready mixed concrete equipment is examined. The variable factors in mock up are diaphragm existence and nonexistence, diaphragm placing hole sizes. To investigate the concrete property under diaphragm, concrete packing ability tests is peformed. High fluidity and strength concrete which satisfied with mix criteria could apply to building construction field. It it is quality managed with use of packing ability analysis.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.613-618
• /
• 2002

Steel slag produced in steel making process is divided with electric arc furnace slag and converter slag. Compared with the blast furnace slag, converter slag has the expansibility due to the reaction with water and free CaO. Therefore it is specified in Standard Specification for Concrete in Korea that steel slag aggregate must not be used in concrete. In this study, we treat electric arc furnace slag aggregate(EAFSA) for concrete before and after several aging process to reduce expansibility. The fundamental properties are measured, which are specific gravity, unit weight, abrasion value and immersion expansion ratio, as concrete aggregate. To understand the suitability of EAFSA for concrete, we made the concrete with EAFSA and then determined the strength and the volume change in EAFSA concrete. From the results EAFSA treated with steam aging process has potentiality for concrete aggregate.

• Computers and Concrete
• /
• v.9 no.1
• /
• pp.21-33
• /
• 2012

This paper presents the numerical simulation of the rigid 12.6 mm diameter kinetic energy ogive-nosed projectile impact on plain and fiber reinforced concrete (FRC) targets with compressive strengths from 45 to 235 MPa, using a three-dimensional finite element code LS-DYNA. A combined dynamic constitutive model, describing the compressive and tensile damage of concrete, is implemented. A modified Johnson_Holmquist_Cook (MJHC) constitutive relationship and damage model are incorporated to simulate the concrete behavior under compression. A tensile damage model is added to the MJHC model to analyze the dynamic fracture behavior of concrete in tension, due to blast loading. As a consequence, the impact damage in targets made of plain and fiber reinforced concrete with same matrix material under same impact velocities (650 m/s) are obtained. Moreover, the damage distribution of concrete after penetration is procured to compare with the experimental results. Numerical simulations provide a reasonable prediction on concrete damage in both compression and tension.