• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.15-21
• /
• 1991

The magnetic properties of the $Y_{1}Ba_{2}Cu_{3-x}Sn_{x}O_{7-y}$ superconductor were studied as a function of Sn concentration by utilizing both the vibrating sample magnetometer (VSM) and torque magnetometer. Unlike the cases where Fe and Co were substituted for Cu, the superconducting transition temperature was maintained above 90 K until x reached the value of 0.36. The lower critical field $H_{c1}(T)$ and upper critical field $H_{c2}(T)$ are measured as a function of temperature and external magnetic field, respectively. By aid of these results, $H_{c1}(0)$.($H_{c2}(0)$), the coherence length ${\varepsilon}_{0}$, the penetration depth ${\lambda}_{0}$, and the Ginzburg-Landau parameter k were oqtained. Flux pinning was also observed in the sample.

• Korean Journal of Materials Research
• /
• v.8 no.7
• /
• pp.579-583
• /
• 1998

Silicide layer structures, agglomeration of silicide layers, and dopant redistributions for the Co/Ti bilayer sputter-deposited on the P-doped polycrystalline Si substrate and subjected to rapid thermal annealing were investigated and compared with those on the single Si substrate. The $CoSi_2$ phase transition temperature is higher and agglomeration of the silicide layer occurs more severely for the Co/Ti bilayer on the doped polycrystalline Si substrate than on the single Si substrate. Also, dopant loss by outdiffusion is much more significant on the doped polycrystalline Si substrate than on the single Si substrate. All of these differences are attributed to the grain boundary diffusion and heavier doping concentration in the polycrystalline Si. The layer structure after silicidation annealing of Co/ Tildoped - polycrystalline Si is polycrystalline CoSi,/polycrystalline Si, while that of Co/TiI( 100) Si is Co- Ti- Si/epi- CoSi,/(lOO) Si.

• Journal of Chest Surgery
• /
• v.29 no.3
• /
• pp.303-310
• /
• 1996

From December of 1994 to April of 1995, we, SHUH Department of Pediatric Thoracic and Cardiovascular Surgery, studied effects of aprotinin. 95 patients were randomly divided into two groups : group I (n=47) with aprotinin and group ll (n=48) without aprotinin. Aprotinin was given as one shot injection to cardiopulmonary bypass perfusion solution with dose of 50,000 KIUikg. Laboratory data such as hemoglobin, hematocrit, BUH, creatinine, fibrinogen, electrolyte concentration, aPTT, PT, and AT R was checked preoperatively, 5 minutes after anesthesia, 5 minutes and 35 minutes after CPB circulation, and 5 minutes, 3 hours, and 24 hours after reperfusion. Also, chest-tube drainage, transfused amount of RBC, platelet concentrate, and fresh frozen plasma within first 24 hours postoperatively were checked and analyzed after transition nn body weight demension. Only RBC transfused postoperatively had statistical significance with P value of less than 0.001. Others had no difference statistical wise. Postoperative side effects of aprotinin was not detected weeks after the surgery and there was no reoperated patient due to postoperative bleeding.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.695-702
• /
• 1994

Current study was undertaken to explain the structural evolution and corresponding changes in the properties of calcium aluminate glasses with the variation of SiO2 doping concentration. Calcium aluminate glasses in the compositional ranges of (100-x)(0.6CaO+0.4Al2O3)+xSiO2(where x=0~60) were fabricated. DTA analysis confirmed an anomalous behavior in glass transition temperature (Tg) with the maximum of 887$^{\circ}C$ and minimum of 859$^{\circ}C$ when x=5 and 50, respectively. densities and refractive indices monotonically decreased with increasing SiO2 content and IR transmitting cutoff shifted to shorter wavelength side when the amount of added SiO2 exceeded 5 mole%. IR fundamental vibration absorption peaks showed the change that NBOs were inclined to SiO4 tetrahedron in the low-silica region and NBO per SiO4 tetrahedra changed from 2 to 0 with increasing silica content. Based on the analysis of IR fundamental vibration absorption peaks, the model of the structural change can be proposed in three step: 1) SiO4 scavenged the NBOs located at AlO4-tetrahedra, which resulted in the increased of Tg values, 2) NBOs located in the main network again with a decrease in Tg, and 3) dominated by the decrease in the relative amount of NBOs in the glass system, where Tg re-increased.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.1
• /
• pp.8-14
• /
• 2015

In this study, the model biomass was used for hydrogen production by supercritical water gasification (SCWG). Model biomasses were glycerol, glycine, lignin and cellulose. The feed concentration was set to 1 wt%. Experiments were conducted in a reactor at $440^{\circ}C$ and above 26.3 MPa for 30 min. The effects of catalysts such as alkali metal salt ($K_2CO_3$ and $Na_2CO_3$) and transition metal salts ($Ni(NO_3)_2$, $Fe(NO_3)_3$ and $Mn(NO_3)_2$) on the gasification were systematically investigated. No tar or coke was observed in all experiments. The results showed that the gasification efficiency increased with various catalysts. For the cellulose and glycerol, all catalysts were effective for the promoted $H_2$ production compared with no catalyst. The significant decrease of $H_2$ production compared with no catalyst was observed with $Na_2CO_3$ and $Fe(NO_3)_3$ for glycine and lignin. respectively. The highest H2 production, 1.24 mmol was obtained for glycerol-SCWG with $Mn(NO_3)_2$. Conclusively, the addition of $Mn(NO_3)_2$ enhanced all model biomass gasification efficiency and increased the hydrogen production promoting the supercritical water reaction.

• Membrane and Water Treatment
• /
• v.1 no.3
• /
• pp.215-230
• /
• 2010

Poly(vinylidene fluoride-co-hexafluoropropylene), PVDF-HFP, hollow fiber membranes were prepared by the dry/wet spinning technique using different polyethylene glycol (PEG) concentrations as non-solvent additive in the dope solution. Two different PEG concentrations (3 and 5 wt.%). The morphology and structural characteristics of the hollow fiber membranes were studied by means of optical microscopy, scanning electron microscopy, atomic force microscopy (AFM) and void volume fraction. The experimental permeate flux and the salt (NaCl) rejection factor were determined using direct contact membrane distillation (DCMD) process. An increase of the PEG content in the spinning solution resulted in a faster coagulation of the PVDF-HFP copolymer and a transition of the cross-section internal layer structure from a sponge-type structure to a finger-type structure. Pore size, nodule size and roughness parameters of both the internal and external hollow fiber surfaces were determined by AFM. It was observed that both the pore size and roughness of the internal surface of the hollow fibers enhanced with increasing the PEG concentration, whereas no change was observed at the outer surface. The void volume fraction increased with the increase of the PEG content in the spinning solution resulting in a higher DCMD flux and a smaller salt rejection factor.

• Elastomers and Composites
• /
• v.47 no.1
• /
• pp.75-81
• /
• 2012

Acrylic rubber was synthesized using ethyl acrylate. butyl acrylate, methoxyethyl acrylate as main monomers and glycidyl methacrylate as cure site monomer by emulsion polymerization. Rubber compound was made by adding 2,2-bis[4-(4-aminophenoxy)phenyl]propane as crosslinking agent. Increase of ethyl acrylate content in the main monomer ratio resulted in enhancement of heat resistance due to decrease of glass transition temperature in acrylic rubber. And also oil resistance was increased with increasing content of ethyl acrylate because ethyl acrylate has the highest ester concentration in the three main monomers. With content of 2,2-bis[4-(4-aminophenoxy)phenyl]propane, both tensile strength and elongation were increased until 2 phr, but in higher content than that, they decreased owing to reduction of viscosity and elongation by increase of crosslinking density.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.294-299
• /
• 2013

Solution polymerization was conducted with water-soluble methacrylic acid (MAA) as a monomer and potassium persulfate (KPS) as an initiator at a selected temperature between $70^{\circ}C$ and $90^{\circ}C$. When the ratio between MAA and water was reduced or initiator concentration increased, molecular weights decreased. Molecular weights of poly(methacrylic acid) (PMAA) showed nearly no dependence on reaction temperature. The Weissenberg effect was observed in most polymerization reactions, while its effect weakened at $90^{\circ}C$. The polydispersity index was less than 1.5 in most of the reactions. An increase in the stirring speed produced PMAAs with increasing molecular weights. When the stirring speed reached 800 rpm, we retrieved a monodisperse PMAA with both the number and weight average molecular weights of 791,000 g/mol. The glass transition temperature was found to be $162^{\circ}C$.

• Journal of Sensor Science and Technology
• /
• v.19 no.2
• /
• pp.155-159
• /
• 2010

0.96$(Na_{0.5}K_{0.5})NbO_3$-0.04$(Ba_{(1-x)}Sr_x)TiO_3$ lead free piezoelectric ceramics were synthesized to enhance the piezoelectric properties of (Na,K)$NbO_3$. The systhesis and sintering method were the conventional solid state reaction method and general sintering method in air atmosphere. The polymorphic phase transition(PPT) was observed at all composition(0 $\leq$ x $\leq$ 0.05) when $(Ba_{(1-x)}Sr_x)TiO_3$ were added in the $(Na_{0.5}K_{0.5})NbO_3$. As Sr concentration was increased, grain size, dielectric loss(tan$\delta$) and mechanical quality factor($Q_m$) were decreased and piezoelectric constant($d_{33}$) and electromechanical coupling factor($k_p$) were increased within a limited value. The optimized piezoelectric and properties, $d_{33}$, $k_p$, $Q_m$, and tand, of 0.96$(Na_{0.5}K_{0.5})NbO_3$-0.04$(Ba_{(1-x)}Sr_x)TiO_3$ were 139 pC/N, 0.31 %, 95, 0.04 at the composition of x=0.04.

• Journal of Soil and Groundwater Environment
• /
• v.23 no.1
• /
• pp.74-84
• /
• 2018

Pot experiments were conducted to assess the applicability of ferric chloride ($FeCl_3$) as a washing agent for laboratory scale in-situ soil washing of paddy soil contaminated with Pb. During the monitoring period for nearly 90 days, the concentrations of Fe and Mn in the soil solution were lower than that of control soil due to lime ($Ca(OH)_2$) amendment for pH recovery. Lime amendment also affected solubility and fractionation of Pb into soil matrix. The result showed that Pb concentrations of soil solution were consistently lower than that of control soil, and the concentration in the exchangeable fraction in washed soil decreased from 13 to 2 mg/kg. There was no significant difference of biomass yield of rice plant in each pots, and Pb contents in rice roots and grains in washed soil decreased to 50 and 78%, respectively, of the control soil. Therefore, $FeCl_3$ could be used as an acceptable in-situ washing agent for agricultural paddy soil if appropriate soil pH management is subsequently practiced.