• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1690-1697
• /
• 2002

The effects of re-peening on the fatigue damaged material are studied in this paper. The effects of re-peening process on surface hardness, surface roughness, surface compressive residual stress, and fatigue life are investigated. The results can be summarized in brief as follows: The depth of hardening layer was increased by re-peening process. There is no large variation of the surface roughness by re-peening process. The compressive residual stress of shot-peened specimen decreases under the fatigue loading and then increases again by re-peening process. Re-peening process increases the fatigue lifo of shot-peened and fatigue damaged specimen. The increase of fatigue lift under high stress level is much higher than under low stress level.

• 대한치과보철학회지
• /
• 제37권2호
• /
• pp.143-166
• /
• 1999

The success of porcelain laminate veneer depends on the bond strength between tooth structure and ceramic restoration and the design of tooth preparation. In particular, incisal coverage and incisal finish line are the two most important factors in long-term fracture resistance. Although the majority of clinicians are practicing incisal coverage and there are various opinions on the geo-metrical ratio between the clinical crown length of the remaining tooth structure and the length of incisal extension in porcelain laminate veneer and the optimal incisal finish lines. scientific evidence still loaves much to be desired. The purpose of this study was to determine the effects of the amounts of incisal coverage and the types of incisal finish line on the stress distribution in maxillary anterior porcelain laminate veneers under two different loading conditions. Three-dimensional finite element models of a maxillary anterior porcelain veneer with differ-ent amounts of incisal coverage ; 0, 1, 2, and 3mm and different incisal finish lines feathered edge, incisal bevel, reverse bevel and lingual chamfer with various amounts of lingual extension were developed. 300N force was applied at the point 0.5mm cervical of the linguoincisal edge in two loading conditions ; A) 125 degrees, B) 132 degrees. Tensile and compressive stress in ceramic and shear stress in the resin cement layer were analyzed using three-dimensional finite element method. The results were as follows : 1. The types of incisal finish line had more influence on the stress distribution in porcelain laminate veneer than the amounts of incisal coverage. 2. In case of no incisal coverage, incisal beveled laminate exhibited more evenly distributed tensile stress than feathered edged laminate. And in case of incisal coverage, reverse beveled laminate and lingual chamfered laminate with 1mm lingual extension exhibited more evenly distributed tensile stress than lingual chamfered laminates with 2mm and 3mm lingual extension. 3. As long as the lingual chamfer goes, less tensile stress was found at the incisal edge, while much more tensile stress was found at the lingual margin area in proportion to the length of lingual extension. 4. Under 125 degree load, tensile stress in porcelain laminate veneer had increased compared with that under 132 degree load and the difference exhibited by the change of the amount of tooth support was larger. 5. The types of incisal finish line and the distance from the incisal finish line to the loading point had more influence on the shear stress distribution in the resin cement layer than the amounts of incisal coverage. In contrast loading condition had little influence.

• Structural Engineering and Mechanics
• /
• 제22권3호
• /
• pp.311-330
• /
• 2006

Standard compression tests of steel fiber reinforced concrete (SFRC) cylinders are conducted to formulate compressive stress versus compressive strain relationship of SFRC. Axial pullout tests of SFRC specimens are also conducted to explore its tensile stress strain relationship. Cover concrete spalling and reinforcement buckling models developed originally for normal reinforced concrete are modified to extend their application to SFRC. Thus obtained monotonic material models of concrete and reinforcing bars in SFRC members are combined with unloading/reloading loops used in the cyclic models of concrete and reinforcing bars in normal reinforced concrete. The resulting path-dependent cyclic material models are then incorporated in a finite-element based fiber analysis program. The applicability of these models at member level is verified by simulating cyclic lateral loading tests of SFRC columns under constant axial compression. The analysis using the proposed SFRC models yield results that are much closer to the experimental results than the analytical results obtained using the normal reinforced concrete models are.

• 터널과지하공간
• /
• 제7권2호
• /
• pp.130-135
• /
• 1997

When crystalline rocks are heated, thermal stress is induced by the differences in thermal expansion of the mineral composition and its orientation. In this study, high temperature uniaxial compressive tests were carried out for Iksan and Hwangdeung granites to study the deformation and failure behavior due to thermal loading. Compressive and tensile strength of Hwangdeung granite for 20$0^{\circ}C$ decreased to 80% and 82% of the room temperature strength, and those of Iksan granite decreased to 90% and 92% for 20$0^{\circ}C$, respectively. Elastic moduli of both granites were decreased sharply at the stress level of 80% of ultimate failure strength. Elastic moduli of both granites by variation of temperature at 50% of ultimate failure strength was decreased as almost linearly.

• 한국지반공학회논문집
• /
• 제28권8호
• /
• pp.65-78
• /
• 2012

탄성계수값은 퇴적암의 일축압축시험을 통하여 응력수준에 따라 넓은 범위로 변하며 거동특성도 다양하게 발현되고 있다. 즉 탄성계수는 정수가 아닌 변수로 볼 수 있는 것이다. 실무에서는 참고자료 및 실험값으로 사용하고 있으나 그 값은 사용하중 수준에서는 매우 큰 값을 채용하고 있다. 설계 및 시공과정에서는 재하-재(再)재하(loading-reloading) 시험을 통한 값을 사용하여 적절하고 합리적인 결과가 도출되어야 할 것이다. 또한 사용하중의 낮은 응력수준에서 발현되는 탄성계수값의 거동특성 역시 유의하여 보아야 할 점이다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.909-914
• /
• 2001

It is important to consider an effect of concrete member sizes when estimating the ACI rectangular stress block of a reinforced concrete flexural member. However, the experimental data and analytical analyses are still not available for a proper evaluation. For all types of loading conditions, the trend is that the size of an ACI rectangular stress block tends to change when the member sizes change. In this paper, the size variations of strength coefficients for ACI rectangular stress block and actual stress distribution have been studied. Results of a series of C-shaped specimens subjected to axial compressive load and bending moment were adopted from references 1 and 2. The analysis results show that the effect of specimen sizes on strength coefficients for ACI rectangular stress block and actual stress distribution of concrete member was apparent. Thus, the results suggest that the current strength criteria based design practice should be reviewed.

• Geomechanics and Engineering
• /
• 제14권3호
• /
• pp.225-231
• /
• 2018

In this paper, in order to explain the splitting of cylindrical rock specimen under uniaxial loading, cracks in cylindrical rock specimen are divided into two kinds, the longitudinal crack and the slanting crack. Mechanical behavior of the rock is described by elastic-brittle-plastic model and splitting is assumed to suddenly occur when the uniaxial compressive strength is reached. Expression of the stresses induced by the longitudinal crack in direction perpendicular to the major axis of the crack is deduced by using the Maxwell model. Results show that the induced stress is tensile and can be greater than the tensile strength even before the uniaxial compressive strength is reached. By using the Inglis's formula and simplifying the cracks as slender ellipse, the above conclusions that drawn by using the Maxwell model are confirmed. Compared to shearing fracture, energy consumption of splitting seems to be less, and splitting is most likely to occur when the uniaxial loading is great and quick. Besides, explaining the rock core disking occurred under the fast axial unloading by using the Maxwell model may be helpful for understanding that rock core disking is fundamentally a tensile failure phenomenon.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.510-513
• /
• 2004

The objectives of this research are to evaluate the effect of the compressive strength of concrete, reinforcing bar size, spacing of column transverse bars related to the concrete confinement effects on anchorage bond strength and bond behavior of beam-column joints subjected to cyclic loading and to predict the bond behavior of beam-column joints according to the variables by Finite Element Analysis appling the interface element between concrete and reinforced bar surface in a three-dimensional configuration. This paper shows that to verify the results by three-dimensional nonlinear finite element analysis appling a interface element, the test results that were already conducted are compared with analytic results. The behavior of bond and anchorage of beam bar is expressed by a local bond stress-slip relationship and the failure mode of bond is predicted by principal stress contour.

• Computers and Concrete
• /
• 제8권3호
• /
• pp.327-341
• /
• 2011

Three-dimensional graphic objects created by MATLAB are exported to the AUTOCAD program through the MATLAB handle functions. The imported SAT format files are used to produce the finite element mesh for MSC.PATRAN. Based on the Monte-Carlo random sample principle, the material heterogeneity of cement composites with randomly distributed fibers is described by the WEIBULL distribution function. In this paper, a concept called "soft region" including micro-defects, micro-voids, etc. is put forward for the simulation of crack propagation in fiber-reinforced cement composites. The performance of the numerical model is demonstrated by several examples involving crack initiation and growth in the composites under three-dimensional stress conditions: tensile loading; compressive loading and crack growth along a bimaterial interface.

• 한국도로학회:학술대회논문집
• /
• 한국도로학회 2010년 추계학술대회 논문집
• /
• pp.99-107
• /
• 2010

A permanent deformation model was developed in this study based on the shear properties of asphalt mixtures such as cohesion and friction angle. Triaxial compressive strength (TCS) and repeated load permanent deformation (RLPD) tests on the three types of asphalt mixtures are performed at various loading and temperature conditions to correlate shear properties of asphalt mixtures to rutting performance. It is observed from the tests results that the ratio of shear stress to strength accurately identifies the mixture rutting performance. It could take care of not only mixture types but also load and temperature conditions dependences. Three different versions of the permanent deformation model based on different input levels are proposed and verified using the tests data. The proposed model based on the ratio of shear stress to strength can successfully predict the permanent deformation of various asphalt mixtures all the way up to the 10% of permanent strain including all three stages of permanent deformation in a wide range of loading and temperature conditions without changing model coefficients.