• 대한기계학회논문집A
• /
• 제37권8호
• /
• pp.991-998
• /
• 2013

클린디젤 차량용 커먼레일 시스템의 연료분사관은 연료레일로부터 각각의 엔진 실린더에 연결된 인젝터로 연료를 공급하는 역할을 하며 반복 내압을 받게 된다. EURO 배기가스 배출규정 만족 및 연비향상을 위하여 요구되는 연료의 압력은 200MPa 이상으로 증가하고 있으며, 성형결함이 발생하지 않는 헤딩공정과 내압 피로수명 향상을 위한 자긴처리 기술이 요구되고 있다. 본 논문에서는 250MPa 급 반복내압을 만족할 수 있는 파이프 소재의 유동응력와 고주기 피로 데이터를 각각의 실험을 통하여 확보하였고, 연료분사관 앞 끝의 성형결함 여부를 판단하기 위하여 헤딩공정에 대한 유한요소해석을 수행하였다. 반복내압에 대한 내구수명 향상 및 신뢰성 확보를 위해 자긴공정에 대한 유한요소해석을 통하여 외경부의 인장잔류응력까지 고려한 최적 공정설계 수행 및 피로해석을 통한 설계의 타당성을 검증하였다.

• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1295-1302
• /
• 2003

In order to evaluate a failure behavior of pipe with notch-type wall thinning, the present study performed full-scale pipe tests using the 102mm, Schedule 80 pipe specimen simulated notch- and circular-type thinning defects. The pipe tests were conducted under the conditions of both monotonic and cyclic bending moment at a constant internal pressure of 10 MPa. From the results. of experiment the failure mode, load carrying capacity, deformation ability, and fatigue life of a notch-type wall thinned pipe were investigated, and they were compared with those of a circular-type wall thinned pipe. The failure mode of notched pipe was similar to that of circular-type thinned pipe under the monotonic bending load. Under the cyclic bending load, however, the mode was clearly distinguished with variation in the shape of wall thinning. The load carrying capacity of a pipe containing notch-type wall thinning was about the same or slightly lower than that of a pipe containing circular-type wall thinning when the thinning area was subjected to tensile stress, whereas it was higher than that of a pipe containing circular-type thinning defect when the thinning area was subjected to compressive stress. On the other hand, the deformation ability and fatigue life of a notch-type wall thinned pipe was lower than those of a circular-type wall thinned pipe.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제17권4호
• /
• pp.325-331
• /
• 2017

Purpose: There is active research that improves both reliability and fatigue life of structures which widely used in the aerospace fields of defense industry. The effects of three parameters (pressure, peening time, nozzle distance) on Almen intensity and coverage will be investigated by using the experimental and analyzed data. Methods: we employed a Box-Behnken design. Additionally, to verify the validity of the optimal condition obtained from experimental results, metallurgical analyses of the shot-peened aerospace part were conducted with respect to surface morphology, residual stress. Results: Optimal shot peening condition is determined as (distance, pressure, time) by optimizing simultaneously the two responses of intensity and coverage. At the optimal peening condition the prediction interval for Almen intensity is well within the required range. And, the validity of the condition was checked by using the real aerospace aluminum alloy plate. Conclusion: Shot peening introduces significant levels of compressive residual stress and induces improves both reliability and fatigue life of structures.

• 한국정밀공학회지
• /
• 제34권2호
• /
• pp.151-156
• /
• 2017

Shot peening is widely used to improve the fatigue life and strength of various mechanical parts and an accurate method is important for the prediction of the compressive residual stress caused by this process. A finite element (FE) model with an elliptical multi-shot is suggested for random-angled impacts. Solutions for compressive residual stress using this model and a normal random vertical-impact one with a spherical multi-shot are obtained and compared. The elliptical multi-shot experimental solution is closer to an X-ray diffraction (XRD) than the spherical one. The FE model's peening coverage also almost reaches the experimental one. The effectiveness of the model based on an elliptical shot ball is confirmed by these results and it can be used instead of previous FE models to evaluate the compressive residual stress produced on the surface of metal by shot peening in various industries.

• 콘크리트학회지
• /
• 제5권4호
• /
• pp.179-187
• /
• 1993

본 연구에서는 콘크리트의 강도수준에 따른 피로실험을 수행하여 고강도 콘크리트의 피로거동 특성을 분석하였다. 실험변수는 4종류의 강도수준(26 MPa, 54 MPa, 82 MPa, 103 MPa)과 4종류의 최고 응력수준(75%, 80%, 85%, 95%)이며 실험에 사용된 공시체는 ${\phi}100{\times}200mm$의 원통형 공시체로서 총 160개가 제작되었다. 실험결과, 강도수준이 증가함에 따라 피로강도가 감소하였고 강도수준의 영향을 고려한 S-N-f'c 관계식을 제안하였다. 또한 강도수준의 영향 이외에도 변형도율 효과를 도입하여 피로실험과 압축실험에서 발생하는 하중재하율의 차이를 보정하였다. 한편, 피로 비탄성변형도는 강도수준이 증가함에 따라 감소하였으나 반복횟수에 따른 변형도 증가율은 강도수준이 높을수록 큰 것으로 나타났다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.156-161
• /
• 2002

It depends on the joint configuration, dimensions and constraints on the joint whether the residual stress at the root of single-sided butt weld is tensile or not. Therefore, recommendation is generally made that high R ratio should be used in the fatigue test of this type of joint in order to prevent excessively long life caused by compressive residual stress. in this research, the residual stress profile in butt weld joint was obtained through compliance method, using successive extension of a slot and measurement of the variation of strain during the slot extension. The residual stress profile was firstly assumed to be the linear summation of Legendre polynomials up to 9th order excluding 0th and 1st order. Strain variation on the surface was measured while the slot was being extended by cutting to find out the 8 unknown coefficients of each polynomial tenn. The cut was made by the electric discharge machine. It was concluded that the residual stress near the surface stayed positive, however, it turned into the negative value as soon as it passed through 2 or 3 mm depth. Several fatigue tests were also carried out under zero stress ratio. Test results showed that fatigue life coincides well with the design cuive of butt joint in British Standards, which supports that it is tensile residual stress that exists near the weld root.

• 한국정밀공학회지
• /
• 제29권1호
• /
• pp.96-102
• /
• 2012

The current establishment of car engineering plastic piping polyethylene (PE) tube used as bonding state or part of the health or safety of fusion is very important. A part of these fusion methods to determine the soundness of the short-term trials and long-term tests can be largely classified. Typical tests included short-term strength, tensile strength, impact strength, compressive strength, resiliency and compression. Polyethylene (PE) pipes installed in the domestic terms of overall penetration rate of 45% has been used. However, polyethylene (PE) pipes have reliability problems, and these occurs mostly in part by defective welding. Therefore, the test is necessary for safety. Non-destructive methods (ultrasonic testing) are difficult to be used. Therefore, Polyethylene (PE) pipe are used. Fusion of thses materilas is necessary in these field however, its technical, and basic research has not been studied well. In this research, short-term strength of welding parts, its tensile strength, hardness, fatigue, and microstructure have been analyzed to find the optimum process conditions to improve mechanical properties.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.564-569
• /
• 2011

The current establishment of city gas piping polyethylene (PE) tube used as bonding state or part of the health or safety of fusion is very important. A part of these fusion methods to determine the soundness of the short-term trials and long-term tests can be largely classified. Typical tests include short-term strength, tensile strength, impact strength, compressive strength, resiliency and compression. Polyethylene (PE) pipes installed in the domestic terms of overall penetration rate of 45% has been used. However, polyethylene (PE) pipes have reliability problems, and these occurs mostly in part by defective welding. Therefore, the test is necessary for safety. Non-destructive methods (ultrasonic testing) are difficult to be used. Therefore, Polypropylene copolymer (PP-C), polypropylene homopolymer (PP-H), and polyethylene (PE) pipe are used. Fusion of these materials is necessary in these field however, its technical, and basic research has not been studied well. In this research, short-term strength of welding parts, its tensile strength, hardness, fatigue, and microstructure have been analyzed to find the optimum process conditions to improve mechanical properties.

• Corrosion Science and Technology
• /
• 제11권5호
• /
• pp.184-190
• /
• 2012

Cu alloy is widely used for marine applications due to its excellent ductility and high resistance for corrosion as wells as cavitation. However, long term exposure of the material to marine environments may result in damages caused by cavitation and corrosion. Water cavitation peening has been introduced in order to improve resistance of Cu alloy to corrosion and cavitation. The technology induces compressive residual stress onto the surface, and thus enhances the fatigue strength and life. In this study, the characteristics of the material were investigated by using water cavitaiton peening technique, and results showed that 2 minutes of water cavitation peening indicated the considerable improvement in hardness. On the other hand, over 10 minutes of water cavitation peening accelerated damages to the surface. In the case of ALBC3, water cavitation peening in the range of 2 to 10 minutes has shown the excellent durability and corrosion resistance while minimizing surface damages.

• 대한기계학회논문집A
• /
• 제33권8호
• /
• pp.767-772
• /
• 2009

Laser shock peening(LSP) is proving to be better surface treatment than conventional one such as shot peening. The LSP process has a compressive residual stress into a metal alloy and a significant improvement in fatigue life. Our research is focused on applying finite element method to the prediction of residual stress through the LSP processing in some LSP conditions such as pressure and spot size induced by laser. Two analysis methods are considered to calculating the compressive residual stress. But the explicit solution and the static one after partially explicit solving are almost same. In LSP, because of very high strain rate($10^6s^{-1}$), HEL(Hugoniot Elastic Limit) is the most important parameter in material behavior modeling. As the circular laser spot is considered, 2-D axisymmetric elements are used and the infinite elements are applied to boundaries for no reflection. The relations of material properties and the LSP are also important parts in this study.