• Structural Engineering and Mechanics
• /
• 제60권4호
• /
• pp.567-594
• /
• 2016

The main objective of the current research is estimating the flexural behavior of ferrocement Ribbed Plates reinforced with composite material. Experimental investigation was carried out on fifteen plates; their dimensions were kept constant at 1200 mm in length, 600 mm width and 100 mm thick but with different volume fraction of steel reinforcement and number of ribs. Test specimens were tested until failure under three line loadings with simply supported conditions over a span of 1100 mm. Cracking patterns, tensile and compressive strains, deformation characteristics, ductility ratio, and energy absorption properties were observed and measured at all stages of loadings. Experimental results were compared to analytical models using ANSYS 10 program. Parametric study is presented to look at the variables that can mainly affect the mechanical behaviors of the model such as the change of plate length. The results showed that the ultimate strength, ductility ratio and energy absorption properties of the proposed ribbed plates are affected by the volume fraction and the type of reinforcement, and also proved the effectiveness of expanded metal mesh and woven steel mesh in reinforcing the ribbed ferrocement plates. In addition, the developed ribbed ferrocement plates have high strength, ductility ratio and energy absorption properties and are lighter in weight compared to the conventional RC ribbed plates, which could be useful for developed and developing countries alike. The Finite Element (FE) simulations gave good results comparing with the experimental results.

• Steel and Composite Structures
• /
• 제22권1호
• /
• pp.63-77
• /
• 2016

Top-down construction is a construction technique in which pit excavation and structure construction are conducted simultaneously. Reducing construction time and minimizing noise and vibration which affect neighboring structures, the technique is widely employed in constructing downtown structures. While H-steel columns have been commonly used as core columns, concrete filled steel tube (CFT) columns are at the center of attention because the latter have less axial directionality and greater cross-sectional efficiency than the former. When compared with circular CFT columns, square CFT columns are more easily connected to the floor structure and the area of percussion rotary drilling (PRD) is smaller. For this reason, square CFT columns are used as core columns of concrete encased and filled square (CET) columns in underground floors. However, studies on the structural behavior and concrete stress transfer of CET columns have not been conducted. Since concrete is cast according to construction sequence, checking the stress of concrete inside the core columns and the stress of covering concrete is essential. This paper presents the results of structural tests and analyses conducted to evaluate the usability and safety of CET columns in top-down construction where CFT columns are used as core columns. Parameters in the tests are loading condition, concrete strength and covering depth. The compressive load capacity and failure behavior of specimens are evaluated. In addition, 2 cases of field application of CET columns in underground floors are analyzed.

• Composites Research
• /
• 제23권4호
• /
• pp.28-34
• /
• 2010

본 논문에서는 일방향 케블라/에폭시 튜브에 대한 현실적인 트리거 모델링을 개발하기 위해 수치해석 모델이 확립하고 시험결과와 비교를 통해 검증하였다. 이를 위해, 4가지 트리거 모델을 제안하고 각각에 대해 상용 외연적 해석 프로그램인 LS-DYNA을 이용하여 유한요소 해석을 통해 축방향 압괴특성을 규명하였다. 유한요소해석에서는 2D 쉘요소와 Chang-Chang 파손기준식을 이용하였다. 또한, 해석에 적용된 소재의 기계적 물성치는 시험을 통해 얻었다. 해석모델은 원형 튜브에 대한 10mm/min의 준정적 압괴시험결과와 비교를 통해 검증하였다. 그 결과 케블라/에폭시 튜브의 하중-변위 곡선은 거의 일치했으며 무게당 흡수 에너지 (SEA)도 5% 미만의 오차에서 잘 일치하였다.

• 한국터널지하공간학회 논문집
• /
• 제2권2호
• /
• pp.72-85
• /
• 2000

암석은 지질학적 생성과정으로 인해 잠재적으로 많은 구조적 결함을 내포하고 있는 재료이다. 이러한 구조적 결함으로 인해 압축하중을 받고 있는 암석의 변형거동 및 파괴는 비선형적이다. 지금까지의 연구들에서는 암석의 비선형 거동을 모사하기 위해 균열모형, 즉 활주균열모형 (Sliding crack model) 과 전단균열모형 (Shear crack model) 을 사용하였다. 이 연구들에서는 암석의 비선형 응력-변형률 곡선과 균열성장으로 인해 발생되는 유효탄성정수들 ($E_1$, $E_2$, ${\nu}_1$, ${\nu}_2$, $G_2$) 의 변화와 같은 여러 가지 암석 거동을 모사하였다 (Kemeny, 1993; Jeon, 1996, 1998). 대부분의 이러한 연구들은 주로 균열모형의 암석거동의 적용에 대한 타당성을 검증하는데 그쳤으며 지하공간이나 사면설계 등의 실제적인 수치해석을 목적으로 균열모형을 적용한 연구는 그다지 많지 않다. 본 연구에서는 암석의 비선형 응력 변형률 곡선을 모사함으로써 균열모형의 암석에의 적용에 대한 타당성을 검증하며 실제적인 수치해석, 즉 상용되고 있는 유한요소해석 프로그램에 균열모형을 적용하였다.

• 한국항해항만학회지
• /
• 제26권1호
• /
• pp.50-54
• /
• 2002

선박은 박판으로 이루어진 상자형구조물이기 때문에 선박이 황천항해를 하게 되면 선체의 상갑판과 선저판에는 호깅이나 새깅이 반복적으로 일어나므로 선테판에는 인장력과 압축력이 반복적으로 작용하게 된다 이 중에서도 압축력이 작용하는 경우가 선박의 종강도상에 치명적인 결과를 가져올 수 있다. 따라서, 본 본문에서는 선체판중에서 종횡비가 1.4인 판을 대상으로 하여 탄소성유한요소해석을 통하여 압축하중을 계속적으로 증가시켜 좌굴과 함께 탄소성대변형거동을 밝힘과 동시에 2차좌굴과 탄소성거동과의 메카니즘을 규명하여 압축하중을 받는 선테판의 탄소성대변형거동을 규명하였다.

• 대한조선학회논문집
• /
• 제48권3호
• /
• pp.275-280
• /
• 2011

In the present study, a unified viscoplastic-damage model has been applied in order to describe the mechanical characteristics of fresh water ice such as nonlinear material behavior and volume fraction. The strain softening phenomenon of fresh water ice under quasi-static compressive loading has been evaluated based on unified viscoplastic model. The material degradation such as growth of slip/fraction has quite close relation with material inside damage. The volume fraction phenomenon of fresh water ice has been identified based on volume fraction (nucleation and growth of damage) model. The viscoplastic-damage model has been transformed to the fully implicit formulation and the discretized formulation has been implemented to ABAQUS user defined subroutine (User MATerial: UMAT) for the benefit of application of commercial finite element program. The proposed computational analysis method has been compared to uni-axial compression test of fresh water ice in order to validate the compatibilities, clarities and usefulness.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권1호
• /
• pp.30-39
• /
• 2017

이 연구에서는 순환굵은골재를 사용하여 31~38 MPa 범주의 압축강도를 갖는 콘크리트의 보의 휨강도 실험연구를 수행하였다. 천연굵은골재에 대한 순환굵은골재의 치환률과 철근비를 실험변수로 고려하였다. 순환굵은골재의 치환률로써 0, 30, 50 및 100%를 고려하였으며, 주철근의 철근비로써 0.50, 0.79 및 1.14%를 고려하였다. 4점 하중재하 시험방법을 통하여 순환골재 콘크리트 보의 균열 및 파괴거동, 하중-처짐 관계 특성을 파악하였다. 천연굵은골재 보와 순환굵은골재 보의 휨균열 형상은 거의 유사하며, 전반적으로 순환굵은골재 보의 균열간격이 천연굵은골재 보의 균열간격보다 작다. 순환골재치환률에 따른 균열폭 크기는 뚜렷한 차이를 나타내지 않는다. 또한, 설계기준에 의한 예측식을 이용하여 실험 부재의 휨강도를 산정하였다.현행 설계기준에 의한 순환골재 콘크리트 보의 휨강도 예측결과는 실제의 휨강도를 과소평가하여 보수적인 설계를 제공하는 것으로 나타난다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.700-702
• /
• 2005

A 5.0-inch transmissive type plastic TFT arrays were successfully fabricated on a plastic substrate at the resolution of $400{\times}3{\times}300$ lines (100ppi). All of the TFT processes were carried out below $150^{\circ}C$ on PES plastic films. After thin film deposition using PECVD, thin film failures such as film delamination and cracking often occurred. For successful growth of thin films (about 1um) without their failures, it is necessary to solve the critical problem related to the internal compressive stress (some GPa) leading to delamination at a threshold thickness value of the films. The Griffith's theory explains the failure process by looking at the excess of elastic energy inside the film, which overcomes the cohesive energy between film and substrate. To increase the above mentioned threshold thickness value there are two possibilities: (i) the improvement of the interface adhesion (for example, through surface micro-roughening and/or surface activation), and (ii) the reduction of the internal stress. In this work, reducing a-Si layer film thickness and optimizing a barrier SiNx layer have produced stable CVD films at 150oC, over PES substrates

• 한국철도학회논문집
• /
• 제13권3호
• /
• pp.271-277
• /
• 2010

본 논문에서는 에너지 흡수부재로 사용될 수 있는 단방향 케블라/에폭시 및 단방향 탄소-케블라/에폭시 튜브의 압괴거동을 예측할 수 있는 해석모델을 확립하고 이를 시험을 통해 검증하였다. 해석모델은 상용 외연적 해석 프로그램인 LS-DYNA의 2D 쉘 요소와 Chang-Chang 파손기준식을 이용하였다. 또한, 해석에 적용된 소재의 기계적 물성치는 시험을 통해 얻었다. 해석모델은 원형 튜브에 대한 10mm/min의 준정적 압괴 시험 결과와 비교를 통해 검증하였다. 그 결과 케블라/에폭시 튜브의 하중-변위 곡선은 거의 일치했으며 무게당 흡수 에너지(SEA)도 6% 미만의 오차에서 잘 일치하였다. 하지만, 탄소-케블라/에폭시 튜브는 시험과 약간의 차이를 보이고 있다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.117-117
• /
• 2016

Total ankle replacement (TAR) is a visible option in the surgical treatment of degenerative or inflammatory diseases of ankle joint. it is attributed to the current TAR which has improvements in surgical technique, uncemented implant fixation and minimally constrained articulation. In the clinical result, they can show promised surgical result when compared to earlier attempts in TAR. However, TAR is still not as successful as total knee replacement (TKR) or total hip replacement (THR), it needs to be note that there are limitations in concerning of long term performance of TAR, the high failure rate still associated with wear of the PE (polyethylene) component that has related with their material property and surface roughness. The aim of this study was to introduce the tribology characteristics of total ankle joint prosthesis with one of TDR model which was fabricated to try multi-axis wear test as a region of motion in ankle joint. The wear specimen of TDR was prepared with Ti-6Al-4V alloy and UHMWPE (ultra-high molecular weight polyethylene) for tibia-talus and bearing component, respectively. A wear test was carried out using a Force 5 (AMTI, Massachusetts, US) wear simulator which can be allowed to move in three axis to flexion-extension ($+3^{\circ}{\sim}-6^{\circ}$), internal-external axial rotation (${\pm}5^{\circ}$), as well as sinusoidal compressive load (1.6 kN, R=10). All tests were performed following standard ISO 14243, wear rate was calculated with weight loss of UHMWPE bearing while the specimen has tested at certain cycles. As based on the preliminary results, wear rate of UHMWPE bearing was $7.9{\times}10^{-6}mg/cycles$ ($R^2=0.86$), calculated loss weight until $10^7cycles$ was 79 mg, respectively.