• Structural Engineering and Mechanics
• /
• 제50권1호
• /
• pp.89-103
• /
• 2014

According to experimental studies made so far, design formula of shear characteristics suggested by ISO 22762 and JEAG 4614, representative design code for Lead Rubber Bearing(LRB) shows dependence caused by changes in compressive stress. Especially, in the case of atypical special structure, such as a nuclear power structure, placement of seismic isolation bearing is more limited compared to that of existing structures and design compressive stress is various in sizes. As a result, there is a difference between design factor and real behavior with regards to shear characteristics of base isolation device, depending on compressive stress. In this study, a full-scale low hardness device of LRB, representative base isolation device was manufactured, analyzed, and then evaluated through an experiment on shear characteristics related to various compressive stresses. With design compressive stress of the full-scale LRB (13MPa) being a basis, changes in shear characteristics were analyzed for compressive stress of 5 MPa, 10 MPa, 13 MPa, 15 MPa, and 20 MPa based on characteristics test specified by ISO 22762:2010 and based on the test result, a regression analysis was made to offer an empirical formula. With application of proposed design formula which reflected the existing design formula and empirical formula, trend of horizontal characteristics was analyzed.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.96-97
• /
• 2020

In this study, the compressive strength and porosity characteristics of cement mortar mixed with liquid and powder composite water repellent were evaluated. When the liquid water repellent was mixed, the compressive strength at 28 days of age was 42% compared to OPC, and the compressive strength was greatly reduced. However, the 28-day compressive strength of the powder water repellent mixture and P5L1, P6L1 liquid and powder composite water repellent was about 97% compared to OPC, and there was little decrease in compressive strength.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.177-178
• /
• 2023

This study evaluated the compressive strength characteristics of steam curing mortar according to the substitution rate of industrial by-products, and showed a tendency to increase the compressive strength when gypsum was substituted up to 30%.

• 소성∙가공
• /
• 제22권2호
• /
• pp.67-73
• /
• 2013

The deformation characteristics and microstructure changes in a round copper pipe under biaxial compression was studied using a horizontal compression die. The change of material properties, punch load and deformation behavior were monitored using various compressive deformation rates in the range of 0.5mm/min.~450mm/min. The strains, either tensile or compressive, were estimated from Vickers microhardness test results. The punch load and deformation characteristics of the round copper pipes were found to change greatly at a deformation rate of about 200mm/min. The punch load decreased with increasing compressive deformation rate. The results of numerical simulations agreed well with what was expected from the final microstructure and the hardness profile estimated from the final deformation strains.

• 환경위생공학
• /
• 제16권1호
• /
• pp.53-60
• /
• 2001

In this study, the heavy metals in tannery sludge were solidified by using cement and power plant fly ash. Solidification characteristics were discussed with the compressive strength and chromium leaching characteristics of solids. The compressive strength of cement mortar was increased by the amount of fly ash up to 24.3~33.8%, which was considered the results of pozzolanic reaction. When the content of fly ash was 20%, cement mortar showed the highest value $295kg/\textrm{cm}^2$ for 28 days curing. At early curing days, solidified chromium tannery sludge solids were showed lower compressive strength because of the retard on the hydration of cement, but the compressive strength was recovered to be more than $140kg/\textrm{cm}^2$ for 28 days curing regardless with the amounts of fly ash. Also, the results of leaching tests by KSM and TCLP method were showed that the solidified chromium sludge have leached out 0.3~2.2% and 11~17%, respectively.

• 한국농공학회논문집
• /
• 제60권1호
• /
• pp.101-110
• /
• 2018

This study experimentally investigated the compressive and flexyral strength development characteristics of polymer concrete using four different type polymeric resins such as unsaturated polyester, vinyl ester, epoxy, and PMMA (polymethyl methacrylate) as binders. The test results show that the average compressive strength of those four different polymer concretes was 88.70 MPa, the average flexural strength was 20.30 MPa. Those test results show that compressive and flexural strengths of polymer concrete were much stronger than compressive and flexural strengths of ordinary Portland cement concrete. In addition, the relative gains of the compressive strength development at the age of 24 hrs compared to the age of 168 hrs were 68.6~88.3 %. Also, the relative gains of the flexural strength development at the age of 24 hrs compared to the age of 168 hrs were 73.8~93.4 %. These test results show that compressive and flexural strengths of each polymer concrete tested in this study were developed at the early age. Moreover, the prediction equations of compressive and flexural strength developments regarding the age were determined. The determined prediction equations could be applied to forecast the compressive and flexural strength developments of polymer concrete investigated in this study because those prediction equations have the high coefficients of correlation. Last, the relations between the compressive strength and the flexural strength of polymer concrete were determined and the flexural/compressive strength ratios were from 1/4 to 1/5. These results show that polymer concretes investigated in this study were appropriate as a flexural member of a concrete structure because the flexural/compressive strength ratios of polymer concrete were much higher than the flexural/compressive strength ratios of Portland cement concrete.

• 한국건설순환자원학회논문집
• /
• 제5권3호
• /
• pp.313-319
• /
• 2017

일반적으로 플라이애시의 입도, 화학성분, 비정질양, 비정질 Si, Al 양등 매우 다양한 요인이 시멘트와의 반응에 영향을 미치고 있다. 본 연구에서는 플라이애시의 입자 특성이 압축강도에 미치는 영향을 확인하고자 한다. 표준사를 플라이애시와 유사한 입도로 분쇄하여 플라이애시와 동일하게 시멘트와 배합하여 압축강도를 측정하였다. 측정된 압축강도 결과 값을 사용하여 시멘트 수화반응에 의한 강도와 입자 충진 효과에 의한 강도 증진을 확인하였다. 표준사 분말을 치환한 모르타르의 압축강도 결과를 활용하여 플라이애시의 포졸란 반응에 의한 강도 증가분을 계산하였다. 이러한 결과 값과 플라이애시의 입자 특성을 비교한 결과, 분말도는 압축강도와 약한 상관성을 보이고 있으며, PI(Pozzolanic Index)는 10% 통과직경(D10)과 50% 통과직경(D50)과 좋은 상관관계를 나타내었다. 따라서 향후 PI와 D10과의 상관성은 플라이애시의 화학적 특성과 함께 플라이애시 특성을 파악하는 좋은 수단이 될 것으로 판단된다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.135-138
• /
• 2004

Because the compressive properties such as compressive stiffness and compressive maximum strength of the fabric composite materials are essential to analyse the drape behaviour and estimate the quality of the final products, compressive tests of fabric composites with different stacking sequences were performed. Appropriate shape and dimensions for the compressive test specimens were prepared and several specimens with different conditions were tested and compared with each other.

• 한국지반공학회논문집
• /
• 제18권4호
• /
• pp.75-83
• /
• 2002

본 연구에서는 준설토, EPS 그리고 고화재를 혼합한 경량혼합토의 역학적 특성을 일축 및 삼축압축시험을 통하여 고찰하였다. 역학적 특성은 다양한 준설토의 초기 함수비, EPS 함유율, 시멘트 함유율 그리고 양생압력에 대한 경량혼합토의 압축강도에 대하여 연구하였다. 삼축압축상태에서 EPS를 함유한 경량혼합토의 압축강도는 유효구속압에 의존 하지 않는 것으로 나타났다. EPS 함유율이 감소할수록($A_E$<2%) 그리고 시멘트 함유율이 증가할수록($A_c$>2%) 삼축압축강도-변형 거동특성은 극한 압축강도를 지나 급격한 압축강도의 감소를 보이는 시멘트 혼합토의 압축강도-변형 거동특성과 유사한 것으로 나타났다. 200kpa 이상의 압축강도를 요구하는 개량지반에 본 경량혼합토를 적용하는 경우에서 적절한 준설토의 초기함수비, EPS 함유율은 각각 약 165%~175%이상 그리고 3%~4%이상으로 제시할 수가 있었다. 삼축 및 일축압축상태에서 극한 압축강도는 시멘트 함유율이 2%이상에서 거의 증가하지 않음으로서 한계 시멘트 함유율은 2%로 제시할 수가 있었다.

• 소성∙가공
• /
• 제15권9호
• /
• pp.635-640
• /
• 2006

Sandwich sheet with inner structure is expected to find many applications because of high stiffness to mass ratio. However, low resistance to the compressive pressure in the thickness direction is a dominating factor in the formability of sandwich sheet. In this study, sandwich sheet with pyramid type core is considered. For the compressive characteristics in the thickness direction, experiments and finite element simulations are carried out. In the experiment, deformation behavior is observed and discussed as the compression proceeds. It is shown that a corresponding finite element simulation can give a reasonable agreement with experiment in terms of maximum pressure. However, simulation shows some discrepancy from the experiment in terms of compressive pressure-displacement characteristics. The reasons for this discrepancy are studied in the geometrical imperfectness of sandwich sheet. It is also observed that most of deformation is dominated by buckling mode of pyramid legs.