• Journal of computational fluids engineering
• /
• v.20 no.4
• /
• pp.36-43
• /
• 2015

Accurate prediction of supersonic transition is required for the heat transfer estimation over supersonic double compression ramp flows. Correlation-based transition models were assessed for a supersonic double ramp problem. Numerical results were compared with experimental data from RWTH Aachen University. A parametric study on the nose bluntness was performed using a selected transition model. As the nose bluntness increases, the boundary layer thickness is increased and the triple point of shock interactions moves downstream. The peak magnitude of the heat transfer is consequently decreased with the nose bluntness.

• Safety and Health at Work
• /
• v.11 no.3
• /
• pp.307-313
• /
• 2020

Background: Many tasks in industrial and health care setting are involved with pushing and pulling tasks up or down on a ramp. An efficient method of moving cart which reduces the risk of low back pain should be concerned. This study aimed to investigate the effects of handling types (HTs) and slope on lumbar spinal load during moving a cart on a ramp. We conducted a 2 × 2 × 4 factorial design with three main factors: 2 HTs, 2 handling directions of moving a cart and 4 degrees of ramp slope. Methods: Thirty healthy male workers performed 14 tasks consist of moving a cart up and down on the ramp of 0°, 10°, 15°, and 20° degrees with pushing and pulling methods. Joint angles from a 3D motion capture system combined with subject height, body weight, and hand forces were used to calculate the spinal load by the 3DSSPP program. Results: Our results showed significant effect of HT, handling directions and slope on compression and shear force of the lumbar spine (p < 0.001). When the ramp gradient increased, the L4/5 compression forces increased in both pushing and pulling (p < 0.001) Shear forces increased in pulling and decreased in pushing in all tasks. At high slopes, pulling generated more compression and shear forces than that of pushing (p < 0.01). Conclusion: Using the appropriate technique of moving a cart on the ramp can reduce the risk of high spinal load, and the pushing is therefore recommended for moving a cart up/down on ramp gradients.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.649-656
• /
• 2004

Hypersonic wind tunnel test of the rectangular variable geometry intake is performed. For realization of a Precooled turbojet engine, development of a hypersonic ramjet engine is planned. To investigate performance of the intake of the hypersonic ramjet engine, wind tunnel test is done with freestream Mach number of 5.1. The total pressure recovery was 18 % with 12.9 % of ramp bleed. Several reasons for low total pressure recovery are shown. Supersonic internal compression is not enough. Then, the throat Mach number is high (M2.61) and total pressure losses at the terminal shock is large. Supersonic flow at the throat and position of the terminal shock is sensitive to a difference of the second ramp's throat height and the third ramp's throat height. Flow separations at the second ramp's trailing edge and the third ramp's leading edge are seen those could result in the trigger of unstart. The seal mechanism between the ramps and the sidewalls is important.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.262-267
• /
• 2008

Numerical investigations were performed with an external-compression inlet with a three-dimensional bump at Mach 2 to scrutinize the geometrical effects of the bump in controlling the interaction of a shock wave with a boundary layer. The inlet was designed for two oblique shock waves and a terminal normal shock wave followed by a subsonic diffuser, with a circular cross-section throughout. The bump-type inlet that replaced the aft ramp of the conventional ramp-type inlet was optimized with respect to the inlet performance parameters as well as compared with the conventional ramp-type inlet. The current numerical simulations showed that a bump-type inlet can provide an improvement in the total pressure recovery downstream of the shock wave/boundary layer interaction over a conventional ramp-type inlet.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.262-267
• /
• 2008

Numerical investigations were performed with an external-compression inlet with a three-dimensional bump at Mach 2 to scrutinize the geometrical effects of the bump in controlling the interaction of a shock wave with a boundary layer. The inlet was designed for two oblique shock waves and a terminal normal shock wave followed by a subsonic diffuser, with a circular cross-section throughout. The bump-type inlet that replaced the aft ramp of the conventional ramp-type inlet was optimized with respect to the inlet performance parameters as well as compared with the conventional ramp-type inlet. The current numerical simulations showed that a bump-type inlet can provide an improvement in the total pressure recovery downstream of the shock wave/boundary layer interaction over a conventional ramp-type inlet.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.5
• /
• pp.297-308
• /
• 2022

Most air-breathing aircraft operated in the hypersonic region are equipped with a scramjet engine. In a scramjet engine, a shock wave generated at an inlet acts as a compressor for a general gas turbine engine instead, so total pressure loss caused by the shock wave is considered very important. In this study, to minimize total pressure loss, a method of designing an external compression inlet using isentropic compression surface was proposed, and an external compression inlet with 3-deflection angles and Busemann inlet were designed under the same conditions. After that, through computational analysis, the performance characteristics at off-design conditions were compared. Each inlet shape was truncated according to the length of the 3-ramp external compression inlet, and the boundary layer correction was performed. The isentropic external compression inlet showed superior performance at the design point, but under the off-design conditions, its performance was degraded compared to the 3-ramp external compression inlet.

• Journal of computational fluids engineering
• /
• v.18 no.2
• /
• pp.56-65
• /
• 2013

Two compression ramp problems and an impinging shock problem are computed to investigate influence of turbulence models and eddy viscosity on the shock-wave / boundary layer interaction. A Navier-Stokes boundary layer generation code was applied to the generation of inflow boundary conditions. Computational results are validated well with the experimental data and effects of turbulence models are investigated. It is shown that the behavior of turbulence (eddy) viscosity directly affects both the extent of the separation and shock-wave positions over the separation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.2
• /
• pp.99-107
• /
• 2016

Test research on Infra-Red Thermography(IRT) technique in a supersonic wind tunnel has been conducted. Inadvertent technical difficulties and their solutions associated with the technique in running of the facility were examined. Two flow conditions at Mach number of 3 and 4 were considered. A double compression ramp model, that replicates realistic high-speed vehicle configuration, was used as test model. The present IR data were compared with shadowgraph visualization images and laminar computational fluid dynamics(CFD) results. It has been shown that the IRT technique can be used in quantifying various fluid dynamic features such as flow transition, separation and three-dimensional phenomena around the double compression ramp model.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.12
• /
• pp.1031-1038
• /
• 2017

In order to improve the performance of the air breathing engines, it is important to maximize the total pressure recovery through air intake. In this study, we investigated whether the Oswatitsch method, which guarantees the maximum pressure recovery for supersonic intake, is effective at hypersonic speed by compressing the intake air with the same intensity at each ramp. The non-linearity of the shock wave normal Mach number at each ramp stage was analyzed by comparing the compression ramp angle and the number of ramp to the inflow Mach number in terms of compressible thermodynamics and the operation limits of the inlet. Based on this analysis, the Oswaitisch technique yields valid conditions not only in supersonic but also hypersonic flight regime.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.585-589
• /
• 2015

본 연구에서는 이중압축램프의 초음속 유동에서 발생하는 충격파 경계층 상호작용을 EDISON_CFD로 해석하기로 한다. 이중압축램프에선 역압력 구배로 인하여 경계층이 박리가 일어나게 되고 박리된 경계층이 다시 이중압축램프에 부착되어 생겨난 박리영역을 관찰할 수 있다. 박리영역의 앞뒤로 유동의 방향이 바뀌게 되면서 압축 팬(compression fan)과 재부착 팬(reattachment fan)이 충격파를 발생시키고 이중압축램프전방의 충격파와 만나서 복잡한 유동 구조를 가지게 됨을 확인하였다. 이와 같은 층류에서 난류, 박리와 재부착의 영역에서의 해석하기 위해선 해석자의 난류모델이 중요하다. $15^{\circ}-30^{\circ}$, $15^{\circ}-45^{\circ}$의 두 종류의 이중압축램프를 $k-{\omega}$ SST 난류 모델과 ${\gamma}-Re_{\theta}$ 천이 모델로 계산을 EDISON_CFD로 수행하였다. 난류 모델의 차이를 표면마찰계수, 압력계수, 마하수로 비교하여 차이점을 분석하였다.