• Journal of the Korean Data and Information Science Society
• /
• v.17 no.3
• /
• pp.945-952
• /
• 2006

Several accelerated life test plans use tests at only two levels of stress and thus, have practical limitations. They highly depend upon the assumption of a linear relationship between stress and time-to-failure and use only two extreme stresses that can cause irrelevant failure modes. Thus 3-level stress plans are preferable. When the lifetime distribution of test unit is exponential with mean lifetime $\theta_i$ at stress $x_i$, i=0, 1, 2, 3, we derive the optimum quadratic plan under the assumption that a quadratic relationship exists between stress and log(mean lifetime), and propose the compound linear plans, as an alternative to the optimum quadratic plan. The proposed compound linear plan is better than two other compromise plans for constant stress testing and nearly as good as the optimum quadratic plan, and has the advantage of simplicity.

• The Korean Journal of Ceramics
• /
• v.6 no.4
• /
• pp.380-384
• /
• 2000

Crystal structure of $Ba_5-5X$Y$_10/3$Nb$_10$O$_30$ was tried to determine by Rietveld analysis using powder X-ray diffraction data. This compound has tetragonal tungsten bronze (TTB) structure with general formula, (Al)$_2$(A2)$_4$(B1)$_2$(B2)$_8$(O1)$_8$(O2)$_8$(O3)$_4$(O4)$_2$(O5)$_4$(O6)$_4$. However, it was difficult to determine the distribution of Ba and Y in Al and A2 sites by the analysis only. Combination of Rietveld analysis and site potentials calculation as well as lattice energy calculations helped to determine the distribution. As the result, it was clarified that $Ba^2+$ cations occupy A2 (pentagonal tunnel site) and $Y^3+$ cations occupy Al (cubic site). The distribution of cations at each site coincides with the distribution estimated by the difference of ionic radii. This supports the formation condition of TTB which was proposed in our previous report. $Ba_5-5X$Y$_10X/3$Nb$_10$O$_30$ shows ferroelectric characteristics. In this compound, remanent polarization decreases slightly with the composition X. On the other hand, the result of crystal structure determination reveals that atomic positions along c-axis for A1, A2, B1 and B2 cations are also decreased with the composition X. This would suggest that the dependence of remanent polarization on composition X is derived by the dependence of atomic coordinates on composition X.

• YAKHAK HOEJI
• /
• v.54 no.4
• /
• pp.300-308
• /
• 2010

Adrenoceptor has been considered to be an important target in psychiatric disorders. Based on x-ray structures of bovine rhodopsin, we established homology model of ${\alpha}_{2c}$-adrenoceptor (ADA2C_rat) and then analyzed docking from binding model of receptor-ligand complex with high-active compound No.29 in tricyclic isoxazole analogues (1-30). We observed that the N (1.907 $\AA$) and O (1.712 $\AA$) atoms of isoxazole ring on the docked ligand (No.29) formed H-bonding interaction with O-H of Ser5.32 and carmeron phenyl ring centroid of tricyclic isoxazole formed $\pi-\pi$ interaction at 3.342 $\AA$ distance with phenyl ring centroid of Phe6.52. According to predictions of blood-brain distribution (logBB) through penetration of blood-brain barrie (BBB) and polar surface area (PSA) of the ligands, the high-active compound No.29 has values of logBB=-0.203, PSA=67.50, respectively. These results suggest that the high-active compound No.29 is a novel anti-depressant with the characteristics such as dopamine and serotonin.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.6
• /
• pp.100-105
• /
• 2012

In previous study, to investigate the impression of the compound lighting based on the AC-Model at the full-size room, the impressions of various compound lighting were completed as compared with that of the uniform lightings through the comparison method (a paired comparison) by Semantic Differential scaling. Also, we examined the effect of the supplementary lighting type increasing the lights at the side of the window and the blind-control lighting type, and they were compared with the existing compound lighting type. In results, pared comparison of the compound lighting and the uniform lighting, indicates that the impression of the compound lighting is generally similar to that of the uniform lighting when there are same ratios of the light from the window. Based on these results, we suggest that the AC-Model might be applied to various conditions. And we also introduce the method for daylighting that it is possible to reduce discomfort glare and to improve visual impressions as the supplementary type and blind-control type on the compound lighting. And it was found that electric power consumption of the compound lighting room was lower than that of the uniform lighting room when as same lighting ratio of the compound lighting and the uniform lighting from the window was provided or there was the lighting distribution simulated to same light ratio from the window. Since the method of the ACModel was described in the experimental condition, additional studies should be performed to determine if this model could be applied to different window configurations, lighting layout and types of a room.

• Journal of Drive and Control
• /
• v.17 no.1
• /
• pp.1-12
• /
• 2020

This study was to develop a simulation model of a compound planetary gear reducer for the final driving shaft using a gear analysis software (KISSsoft, Version 2017, KISSsoft AG, Switzerland). The aim of this study is to analyze transmission error and the tooth load distribution through micro-geometry using the simulation model. The tip and root relief were modified with Micro-geometry in the profile direction, and crowning was modified with Micro-geometry in the lead direction. The transmission error was analyzed using the PPTE (Peak to Peak Transmission Error) value, and the tooth load distribution was analyzed for the concentrated stress on the tooth surface. As a result of modifying tip and relief in the profile direction, the transmission error was reduced up to 40.7%. In the case of modifying crowning in the lead direction, the tooth load was more evenly distributed than before and decreased the stress on the tooth surface. After modifying the profile direction for the 1st and 2nd planetary gear train, the bending and contact safety factors were increased by 31.7% and 17%, and 18.3% and 12.5% respectively. Moreover, the bending and safety factors after modifying lead direction were increased by 59.5% and 32.7%, respectively for the 1st planetary gear train, and 59.6% and 43.6%, respectively for the 2nd planetary gear train. In future studies, the optimal design of a compound planetary gear reducer for the final driving shaft is needed considering both the transmission error and tooth load distribution.

• Steel and Composite Structures
• /
• v.38 no.1
• /
• pp.79-86
• /
• 2021

Due to the complex geological conditions, a large number of high quality coal seams was buried in the western of China which cannot be mining in open-pit methods. The dynamic properties of that coal cannot be studied easily in real site for the complex working condition. The compound coal blocks made on the basis of the real situation were studied in the laboratory. The physical and mechanical properties of the compound coal blocks and the raw coal were contrasted by using the UCS tests. The results show that the compound coal blocks made by mixing coal powder, cement and water in proportion of 2.5:2:1 are the closest to that of standard raw coal. Then the propagation of strain waves and crushing effects on the coal were studied in the compound coal blocks by using the super dynamic strain test system and the numerical calculated method of ANSYS/LS-DYNA. The results show that the diameter of the crushing zone in the compound coal blocks was similar to that in the numerical results. The fractures distribution in laboratory tests also has a similar trend to the calculation results. The measured strain waves at the distance of 50 cm, 100 cm, and 150 cm from the center of the charge are mainly concerned at -1.0×104 με and have a similar trend as that in the numerical simulation.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.24 no.3
• /
• pp.109-123
• /
• 1999

Fleet sizing and empty equipment redistribution are two of the most critical problems in managing a fleet of equipment over a transportation network. Where the demand pattern followed the compound Poisson process(CPP) which can be generated one or more at a time under homogeneous Poisson process(HPP), this paper presented a mathematical model to determine control parameters of a decentralized distribution policy and fleet size in case of the pure hub-and-spoke system, a popular form of a logistics system. and validated this model by simulation. That is, where the number of demanded equipments followed geometric and binomial distributions, respectively, cost models on the pure hub-and-spoke logistics system with deterministic trans-portation times, which could be solved analytically, were established and analyzed. We also compared the deterministic case with stochastic one that the transportation time follows some probability distributions.

• Journal of Ginseng Research
• /
• v.22 no.2
• /
• pp.91-95
• /
• 1998

The distribution of phenolic components of Korean ginseng (Panax ginseng KG) and American ginseng (Panax quinquefolium, AG) were compared by thin-layer chromatography (TLC). Silica gel TLC gave 3~4 spots, while $NH_2$ HPTLC 5~6 spots, which were colored by both $FeCl_3$/$K_3Fe(CN)_6$ and Folin-Ciocalteu. The distribution of phenolic components was quite different between KG and AG. Especially, a polyphenol (m.w. 578), which had been isolated from KG by the author, was not found in AG. This result suggests that the polyphenol could be used as an index compound for the differentiation of KG from AG.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.12 no.2
• /
• pp.81-95
• /
• 2008

In this paper, the negative Polya-Eggenberger distribution has been introduced by compounding negative binomial distribution with beta distribution of I-kind which generates a number of univariate contagious or compound (or mixture of) distributions as its particular cases. The distribution is unimode, over dispersed and all of its positive and negative integer moments exist. The difference equation of the proposed model shows that it is a member of the Ord's family of distribution. Some of its interesting properties have been explored besides different methods of estimation been discussed. Finally, the parameters of the proposed model have been estimated by using a computer programme in R-software. Application of the proposed model to some data, available in the literature, has been given and its goodness of fit demonstrated.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.637-642
• /
• 2012

The effects of mixing geometry (intermeshing vs. tangential rotor) for the dispersion and distribution of silica agglomerates in SBR/BR compound were investigated. Silica dispersion and distribution were found to be better with the intermeshing rotor compared to the tangential rotor. It was concluded that the intermeshing rotor compared to the tangential rotor delivered a higher shear stress due to interlocked rotor geometry to silica agglomerates leading to better dispersity and distribution of silica in the agglomerates.