• Steel and Composite Structures
• /
• v.49 no.2
• /
• pp.245-255
• /
• 2023

The present paper summarizes the results of an experimental program on the influence of using waste lathe scraps in the concrete mixture on the shear behavior of RC beams with different amounts of shear reinforcement. Three different volumetric ratios (1, 2 and %3) for the scraps and three different stirrup spacings (160, 200 and 270 mm) were adopted in the tests. The shear span-to-depth ratios of the beams were 2.67 and the stirrup spacing exceeded the maximum spacing limit in the building codes to unfold the contribution of lathe scraps to the shear resistances of shear-deficient beams, subject to shear-dominated failure (shear-tension). The experiments depicted that the lathe scraps have a pronounced contribution to the shear strength and load-deflection behavior of RC beams with widely-spaced stirrups. Namely, with the addition of 1%, 2% and 3% waste lathe scraps, the load-bearing capacity escalated by 9.1%, 21.8% and 32.8%, respectively, compared to the reference beam. On the other hand, the contribution of the lathe scraps to the load capacity decreases with decreasing stirrup spacing, since the closely-spaced stirrups bear the shear stresses and render the contribution of the scraps to shear resistance insignificant. The load capacity, deformation ductility index (DDI) and modulus of toughness (MOT) values of the beams were shown to increase with the volumetric fraction of scraps if the stirrups are spaced at about two times the beam depth. For the specimens with a stirrup spacing of about the beam depth, the scraps were found to have no considerable contribution to the load capacity and the deformation capacity beyond the ultimate load. In other words, for lathe scrap contents of 1-3%, the DDI values increased by 5-23% and the MOT values by 63.5-165% with respect to the reference beam with a stirrup spacing of 270 mm. The influence of the lathe scraps to the DDI and MOT values were rather limited and even sometimes negative for the stirrup spacing values of 160 and 200 mm.

• Composites Research
• /
• v.37 no.3
• /
• pp.209-214
• /
• 2024

Graphene oxide (GO), known for its high stiffness, thermal conductivity, and electrical conductivity, is being utilized as a reinforcement in nanocomposite materials. This study evaluates the mechanical properties of epoxy nanocomposites incorporating GO and edge modified GO (E-GO), which has hydroxyl groups substituted only on its edges. GO/E-GO was uniformly dispersed in epoxy resin using ultrasonic dispersion, and mechanical properties were assessed through tensile testing. The results showed that the addition of nanoparticles increased both tensile strength and toughness. The tensile strength of the epoxy without nanoparticles was 74.4 MPa, while the highest tensile strength of 90.7 MPa was observed with 0.3 wt% E-GO. Additionally, the modulus increased from 2.55 GPa to 3.53 GPa with the addition of nanoparticles. Field emission scanning electron microscopy of the fracture surface revealed that the growth of cracks was impeded by the nanoparticles, preventing complete fracture and causing the cracks to split in multiple directions. E-GO, with surface treatment only on the edges, exhibited higher mechanical properties than GO due to its superior dispersion and surface treatment effects. These results highlight the importance of nanoparticle surface treatment in developing high-performance nanocomposite materials.

• Journal of Distribution Research
• /
• v.17 no.3
• /
• pp.59-92
• /
• 2012

With accumulated research evidence, there is little doubt that leadership behavior is related to a wide variety of positive individual and organizational outcomes. Indeed, leadership behavior has been empirically linked to increased employee satisfaction, organizational commitment, extra effort, turnover intention, organizational citizenship behavior, and overall employee performance. Although leadership behavior has been linked to a number of positive organizational outcomes, research regarding the antecedents of such behavior is limited. Especially there is little research dealing with the antecedents of inter-organizational leadership behavior. This study interests in inter-organizational ethical leadership among marketing channel members. In both the mass media and the academic association, there has been a surge in interest in the ethical and unethical behavior of leaders. Although the corporate scandals in recent years may explain much of the mass media and popular focus, academics' interest has been limited by evidence that ethical leadership behavior is associated with both positive and negative inter-organizational processes and performances. This study tried to contribute to this body of knowledge by examining antecedents of ethical leadership. Ethical leadership is defined "the demonstration of normatively appropriate conduct through personal actions and interpersonal relationships, and the promotion of such conduct to followers through two-way communication, reinforcement, and decision-making." Ethical leaders not only inform individuals of the behefits of ethical behavior and the cost of inappropriate behavior, such leaders also set clear standards and use rewards and fair and balanced punishment to hold followers accountable for their ethical conduct. Despite the assume importance and prominence of ethical leadership among organizations, there are still many questions relating to its antecedents and consequences. One is whether the likelihood of an leading organization being perceived as an ethical leader among other following organizations in marketing channels can be predicted using its characteristics and inter-organizational relationship maintenance skills. Identifying trait and skill antecedents will aid in the development of strategies for selecting and developing ethical leaders and determining the best means to reinforce ethical behaviors. The purpose of this study is to investigate the effects of three categorized variables on ethical leadership of channel leader. To be concrete, this study develops a model of the antecedents of three conceptually distinct forms of channel leader characteristics, such as organizational traits, inter-organizational relationship maintenance strategies, and supplier management strategies, and tests the hypothesized differential effects on ethical leadership of marketing channel leaders. The reason why this study deals with discount store channel is that there is very strong inter-dependence between a discount store and its suppliers. Their strong inter-dependence makes their relationship as the relationship between a leader and suppliers and creates an atmosphere that leadership occur without difficulty. The research model is as follows. For the purpose of empirical testing, 295 respondents of suppliers of discount store channel in Korea were surveyed. The procedures included scale reliability, and discriminant and convergent validity were used to validate measures. Also, the reliability measurements traditionally employed, such as the Cronbach's alpha, were used. All the reliabilities were greater than .70. This study conducted confirmatory factor analyses to assess the validity of our measurements. All items loaded significantly on their respective constructs(with the lowest t-value being 15.2), providing support for convergent validity. We then examined composite reliability and average variance extracted(AVE). The composite reliability of each construct was greater than .70. The AVE of each construct was greater than .50. This study tested research model using Partial Least Square(PLS). The estimation of the structural equation model revealed an acceptable fit of the model to the data($r^2$=.851). Thus, This study concluded that the model fit was considered acceptable. The results of PLS are as follows. The results indicated that conscientiousness, openness, conflict management, social networks, training, fair reward had positive effects on ethical leadership of channel leaders. On the other hand, emotional insecure had negative effect and agreeableness, assurance, and inter-organizational communication had no significant effect on supply chain leadership.

• The Journal of Engineering Geology
• /
• v.27 no.3
• /
• pp.331-343
• /
• 2017

In this study to improve stability, workability and economics of the H-Pile+Earth plate or H-Pile+Earth plate+Cutoff grouting currently in use, we had developed HCS method belonging to the retaining wall which is consisting of a combination H-Pile, Plastic Sheet Pile and Steel Square Pipe for gap maintenance and reinforcement of flexible plastic Sheet Pile, and the behavior of each member composing HCS method is investigated by three-dimensional finite element analysis. To numerically analyze the behavior of the HCS method, we have performed extensive three-dimentional finite element analysis for three kinds of plastic Sheet Pile size, two kinds of H-Pile size and three kinds of H-Pile installation interval, one kinds of Steel Square Pipe and three kinds of Steel Square Pipe installation interval. After analyzing the numerical results, we found that the combinations of $P.S.P-460{\times}131.5{\times}7t$ (PS7) and H-Pile $250{\times}250{\times}9{\times}14$ (H250), $P.S.P473{\times}133.5{\times}9t$ (PS9) and H-Pile $300{\times}200{\times}9{\times}14$ (H300) is the most economical because these combinations are considered to have a stress ratio (=applied stress/allowable stress) close to that as the stiffness of H-Pile, plastic Sheet Pile and Steel Square Pipe composite increased, the horizontal displacement of the retaining wall and the vertical displacement of the upper ground decreased. Especially, due to the arching effects caused by the difference in stiffness between H-Pile and plastic Sheet Pile, a large part of the earth pressure acting on plastic Sheet Pile caused a stress transfer to H-Pile, and the stress and displacement of plastic Sheet Pile were small. Through this study, we can confirm the behavior of each member constituting the HCS method, and based on the confirmed results of this study, it can be used to apply HCS method in reasonable, stable and economical way in the future.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.39 no.2
• /
• pp.206-225
• /
• 2012

General status of pediatric dentistry in Korea is to conduct vigorous academic activities and specialized medical care centering the Korean Association of Pediatric Dentistry (KAPD) that has about 1,000 pediatric dentists as members, pediatric dentistry departments of 11 Colleges of Dentistry, numbers of pediatric dentistry training institutions and private clinics specialized in children. From 1996, the accredited pediatric dentists were produced by the KAPD and from 2008, the state began to produce the accredited pediatric dentists. Since then, doctors with expertise in pediatric care had opened private clinics in addition to the university hospitals, it became the basis of a momentum to deepen the specialty of pediatric dentistry. The Dentistry community of Korea is going through rapid and profound changes recently, and the underlying reasons for such changes can be classified largely into a few categories: (1) Decreasing population and structural changes in population (2) Increase in numbers of dentists, (3) Changes in the pattern of dental diseases and (4) Changes in medical environment. In Korea, the children population in the age range of 0 ~ 14 years old had been decreased by 2 million in 2010 compared to that of 2000 due to reduction of birth rate. The current population of children in the age range of 0 ~ 4 years old in 2010 takes up 16.2% of the total population, but it is estimated that such percentage would decrease to 8.0% by 2050. Such percentage is largely behind the estimated mean global population of 19.6% by 2050. On the other hand, the number of dentists had been largely increased from 18,000 in 2000 to 25,000 in 2010. And it is estimated that the number will be increased to 41,000 by 2030. In addition, the specialized personnel of Pediatric dentistry had been shown as increased by 2.5 times during past 10 years. For the changes in the pattern of dental diseases, including dental caries, each df rate of 5 years old children and 12 years old children had been decreased by 21.9% and 16.7% respectively in 2010 compared to 2000. Each df Index also had been decreased by 2.5 teeth and 1.2 teeth respectively. The medical expenditure of Korea is less than that of OECD and more specifically, the expenditure from the National Health Plan is less than OECD but the expenditure covered by households is larger than OECD. These facts indicate that it is considered as requiring the coverage of the national health plan to be reinforced more in the future and as such reinforcement needs continuous promotion. In medical examination pattern of Pediatric dentistry, the preventive and corrective treatment were increased whereas the restorative treatment was decreased. It is considered that such change is caused from decrease of dental caries from activation of the prevention project at national level. For the restorative treatment, the restorations in use of dental amalgam, pre-existing gold crowning and endodontic treatment had been decreased in their proportion while the restorative treatment in use of composite resin had been increased. It is considered that such changes is caused by the change of demands from patients and family or guardians as they desired more aesthetic improvement along with socio-economic growth of Korean society. Due to such changes in dentistry, the pediatric dentistry in Korea also attempts to have changes in the patterns of medical examination as follows; It tends to implement early stage treatment through early diagnosis utilizing various diagnostic tools such as FOTI or QLF. The early stage dental caries so called white spot had been included in the subjects for dental care or management and in order to do so, the medical care guidelines essentially accompanied with remineralization treatment as well as minimally invasive treatment is being generalized gradually. Also, centering the Pediatric dentists, the importance of caries risk assessment is being recognized, in addition that the management of dental caries is being changed from surgical approach to internal medicinal approach. Recently, efforts began to emerge in order to increase the target patients to be managed by dentists and to expand the application scope of Pediatric dentistry along with through such changes. The interest and activities of Pediatric dentists which had been limited to the medical examination room so far, is now being expanded externally, as they put efforts for participating in the preventive policy making process of the community or the state, and to support the political theories. And also opinions are being collected into the direction that the future- oriented strategic political tasks shall be selected and researches as well as presentations on the theoretical rationale of such tasks at the association level.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.1
• /
• pp.73-80
• /
• 2022

In this study, details of NRC beam-column connections were developed in which beam and columns pre-assembled in factories using steel angles were bolted on site. The developed joint details are NRC-J type and NRC-JD type. NRC-J type is a method of tensile joining with TS bolts to the side and lower surfaces of the side plate of the NRC column and the end plate of the NRC beam. NRC-JD type has a rigid joint with high-strength bolts between the NRC beam and the side of the NRC column for shear, and with lap splices of reinforcing bar penetrating the joint and the beam main reinforcement for bending. For the seismic performance evaluation of the joint, three specimens were tested: an NRC-J specimen and NRC-JD specimen with NRC beam-column joint details, and an RC-J specimen with RC beam-column joint detail. As a result of the repeated lateral load test, the final failure mode of all specimens was the bending fracture of the beam at the beam-column interface. Compared to the RC-J specimen, the maximum strength of the specimen by the positive force was 10.1% and 29.6% higher in the NRC-J specimen and the NRC-JD specimen, respectively. Both NRC joint details were evaluated to secure ductility of 0.03 rad or more, the minimum total inter-story displacement angle required for the composite intermediate moment frame according to the KDS standard (KDS 41 31 00). At the slope by relative storey displacemet of 5.7%, the NRC-J specimen and the NRC-JD specimen had about 34.8% and 61.1% greater cumulative energy dissipation capacity than the RC specimen. The experimental strength of the NRC beam-column connection was evaluated to be 30% to 53% greater than the theoretical strength according to the KDS standard formula, and the standard formula evaluated the joint performance as a safety side.