• Journal of Powder Materials
• /
• v.21 no.2
• /
• pp.93-96
• /
• 2014

Cobalt coated tungsten carbide-cobalt composite powder has been prepared through wet chemical reduction method. The cobalt sulfate solution was converted to the cobalt chloride then the cobalt hydroxide. The tungsten carbide powders were added in to the cobalt hydroxide, the cobalt hydroxide was reduced and coated over tungsten carbide powder using hypo-phosphorous acid. Both the cobalt and the tungsten carbide phase peaks were evident in the tungsten carbide-cobalt composite powder by X-ray diffraction. The average particle size measured via scanning electron microscope, particle size analysis was around 380 nm and the thickness of coated cobalt was determined to be 30~40 nm by transmission electron microscopy.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.33-38
• /
• 1996

High temperature wear behaviors of plasma-sprayed ZrO$_{2}$-$Y_{2}O_{3}$ composite coatings were investigated for high temperature wear resistance applications. The composite powders containing 20, 50, 80 vol% of alumina for plasma spray were made by spray drying method. Wear tests with composite coated specimens were performed at temperature ranges from room temperature to 800$^{\circ}$C. Wear tests were also carried out with heat treated specimens at room temperature. The microstructural change of coatings and the worn surface were examined by SEM and XRD. Sharp increase of wear loss at high temperature wear test was observed in specimens containing 50 and 80 vol% alumina. Similar trend was observed in the heat treated coatings. The measured residual stress was increased with increased alumina contents and heat treating temperatures. Residual stress induced during heat treatment appeared to be responsible to the observed harmful effect of alumina additions on the high temperature wear.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1271-1272
• /
• 2006

The vacuum infiltration method is one of the composite producing methods. There are several parameters in composite production by vacuum infiltration. One of them is particle size of reinforcement in particulate reinforced composites. In this study, MgO powder and Al were used as reinforcement and matrix respectively. MgO powders with different size and amount to give same height were filled in quartz tubes and liquid metal was vacuum infiltrated into the MgO powder under same vacuum condition and for same time. Infiltration height was measured and microstructure and fracture behavior of composite were investigated. It has been found that infiltration height and fracture strength were increased with particulate reinforcement sizes. It has also been determined that molten metal temperature facilitates infiltration.

• Journal of Powder Materials
• /
• v.22 no.5
• /
• pp.356-361
• /
• 2015

Fe-30 wt% TiC composite powders are fabricated by in situ reaction synthesis after planetary ball milling of (Fe, $TiH_2$, Carbon) powder mixture. Two sintering methods of a pressureless sintering and a spark-plasma sintering are tested to densify the Fe-30 wt% TiC composite powder compacts. Pressureless sintering is performed at 1100, 1200 and $1300^{\circ}C$ for 1-3 hours in a tube furnace under flowing argon gas atmosphere. Spark-plasma sintering is carried out under the following condition: sintering temperature of $1050^{\circ}C$, soaking time of 10 min, sintering pressure of 50 MPa, heating rate of $50^{\circ}C/min$, and in a vacuum of 0.1 Pa. The curves of shrinkage and its derivative (shrinkage rate) are obtained from the data stored automatically during sintering process. The densification behaviors are investigated from the observation of fracture surface and cross-section of the sintered compacts. The pressureless-sintered powder compacts are not densified even after sintering at $1300^{\circ}C$ for 3 h, which shows a relative denstiy of 66.9%. Spark-plasma sintering at $1050^{\circ}C$ for 10 min exhibits nearly full densification of 99.6% relative density under the sintering pressure of 50 MPa.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.4
• /
• pp.59-65
• /
• 2001

Epoxy/$BaTiO_3$composite capacitor films with excellent stability at room temperature, uniform thickness, and electrical properties over a large area ware successfully fabricated. The composite capacitor films with good film formation capability and easy process ability were made from epoxy resin developed for ACF as a matrix and two kinds of $BaTiO_3$powders as fillers to increase the dielectric constant of the composite film. The crystal structure of the powders and its effects on dielectric constant of the films were investigated by X-ray diffraction (XRD). And the optimum amount of dispersant, phosphate ester, was determined by viscosity measurement of suspension. DSC and dielectric property tests were conducted to decide the right curing temperature and the optimum amount of the curing agent. As a result, the capacitors of 7 $\mu \textrm{m}$ thick film with 10 nF/$\textrm{cm}^2$ and low leakage current were successfully demonstrated.

• Journal of Powder Materials
• /
• v.21 no.3
• /
• pp.229-234
• /
• 2014

This study manufactured a CIG-based composite coating layer utilizing a new warm spray process, and a mixed powder of Cu-20at.%Ga and Cu-20at.%In. In order to obtain the mixed powder with desired composition, the Cu-20at.%Ga and Cu-20at.%In powders were mixed with a 7:1 ratio. The mixed powder had an average particle size of $35.4{\mu}m$. Through the utilization of a warm spray process, a CIG-based composite coating layer of $180{\mu}m$ thickness could be manufactured on a pure Al matrix. To analyze the microstructure and phase, the warm sprayed coating layer underwent XRD, SEM/EDS and EMPA analyses. In addition, to improve the physical properties of the coating layer, an annealing heat treatment was conducted at temperatures of $200^{\circ}C$, $400^{\circ}C$ and $600^{\circ}C$ for 1 hour each. The microstructure analysis identified ${\alpha}$-Cu, $Cu_4In$ and $Cu_3Ga$ phases in the early mixed powder, while $Cu_4In$ disappeared, and additional $Cu_9In_4$ and $Cu_9Ga_4$ phases were identified in the warm sprayed coating layer. Porosity after annealing heat treatment reduced from 0.75% (warm sprayed coating layer) to 0.6% (after $600^{\circ}C/1hr$. heat treatment), and hardness reduced from 288 Hv to 190 Hv. No significant phase changes were found after annealing heat treatment.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1205-1210
• /
• 1999

Far infrared ceramic/aluminum composite powders for thermal spray were fabricated by spray drying method and investigated the characteristics of the plasma sprayed coating layers, I.e. microstructure, phases, thermal shock resistance and spectral emissivity. The shape of the spray dried composite powder was spherical and the particle size distribution was 34~105${\mu}m $. Aluminum was distributed homogeneously in the spray dried composite powder. Spectral emissivity of the plasma sprayed coating layer ranges from 3 to 14${\mu}m $ whereas spectral emissivity of the raw ceramic powder ranges from 8 to 14${\mu}m $. And then spectral emissivity of the coatings was better than that of the raw powder but spectral emissivity was decreased with increasing aluminum content. It was found that aluminum content ranging from 20 to 30wt% was suitable for fabricating far-infrared radiator by plasma spraying method.

• Journal of Powder Materials
• /
• v.26 no.4
• /
• pp.290-298
• /
• 2019

$TiO_2$-particles containing Co grains are fabricated via thermal hydrogenation and selective oxidation of TiCo alloy. For comparison, $TiO_2$-Co composite powders are prepared by two kinds of methods which were the mechanical carbonization and oxidation process, and the conventional mixing process. The microstructural characteristics of the prepared composites are analyzed by X-ray diffraction, field-emission scattering electron microscopy, and transmission electron microscopy. In addition, the composite powders are sintered at $800^{\circ}C$ by spark plasma sintering. The flexural strength and fracture toughness of the sintered samples prepared by thermal hydrogenation and mechanical carbonization are found to be higher than those of the samples prepared by the conventional mixing process. Moreover, the microstructures of sintered samples prepared by thermal hydrogenation and mechanical carbonization processes are found to be similar. The difference in the mechanical properties of sintered samples prepared by thermal hydrogenation and mechanical carbonization processes is attributed to the different sizes of metallic Co particles in the samples.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.11a
• /
• pp.45.1-45.1
• /
• 2008

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.05a
• /
• pp.20-20
• /
• 2002