• Computers and Concrete
• /
• v.24 no.2
• /
• pp.159-172
• /
• 2019

This paper presents an investigation into the flexural behavior of reinforced concrete (RC) beams retrofitted by ultra-high performance fiber-reinforced concrete (UHPFRC) layers. The experimental study has been conducted in two parts. In the first part, four methods of retrofitting with UHPFRC layers in both the up and down sides of the beams have been proposed and their efficiency in the bonding of the normal concrete and ultra-high performance fiber-reinforced concrete has been discussed. The results showed that using the grooving method and the pre-casted UHPFRC layers in comparison with the sandblasting method and the cast-in-place UHPFRC layers leads to increase the load carrying capacity and the energy absorption capacity and causes high bond strength between two concretes. In the second part of the experimental study, the tests have been conducted on the beams with single UHPFRC layer in the down side and in the up side, using the effective retrofitting method chosen from the first part. The results are compared with those of non-retrofitted beam and the results of the first part of experimental study. The results showed that the retrofitted beam with two UHPFRC layers in the up and down sides has the highest energy absorption and load carrying capacity. A finite element analysis was applied to prediction the flexural behavior of the composite beams. A good agreement was achieved between the finite element and experimental results. Finally, a parametric study was carried out on full-scale retrofitted beams. The results indicated that in all retrofitted beams with UHPFRC in single and two sides, increasing of the UHPFRC layer thickness causes the load carrying capacity to be increased. Also, increases of the normal concrete compressive strength improved the cracking load of the beams.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.3
• /
• pp.321-327
• /
• 2019

The purpose of this study is paper is to improve the flow performance and to reduce the aerodynamic noise of air discharge system consisting of a centrifugal fan, ducts and a housing for the clothes dryer. Using computational fluid dynamics and acoustic analogy based on FW-H (Ffowcs-Williams and Hawkings) Eq., air flow field and acoustic fields of the air discharge system are investigated. To optimize aerodynamic performance and aerodynamic noise, the response surface method is employed. The two factors central composite design using the inflow and outflow angles of fan blades is adopted. The devised optimum design shows the reduction of turbulent kinetic energy in the ducts and the housing of the system, and as a result, the improved flow rate and reduce noise is confirmed. Finally, the experment using the proto-type manufactured usign the optimum design shows the increase of flow rate by 4.2 %.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.54 no.5
• /
• pp.724-732
• /
• 2021

This study used response surface methodology to investigate the optimal conditions to reduce the bitterness of alcalase-treated anchovy hydrolysate (AAH) by the aminopeptidase active fraction (AAF) derived from the common squid Todarodes pacificus hepatopancreas. The central composite design selected AAF/AAH ratio (X₁, %) and hydrolysis time (X₂, h) as independent variables, and the degree of hydrolysis (Y₁) and bitterness (Y₂) as dependent variables. The uncoded values of the multiple response optimization for independent variables were 3.4% for the AAF/AAH ratio and 9.2 h for the hydrolysis time. The predicted values of the yield and bitterness score of alcalase-AAF continuously treated anchovy hydrolysate (AAAH) under the optimized conditions were 68.9% and 4.6 points, respectively. Their measured values of 69.5% for yield and 4.6±0.5 points for bitterness were similar to the predicted values. The food components of AAAH were 91.4% (moisture), 7.5% (protein), 0.1% (lipid) and 0.6% (ash). The findings indicate the potential value for use as an anchovy seasoning base. The results also confirm that the bitterness of AAH was remarkably improved by AAF and implicates AAF derived from squid hepatopancreas as a good enzyme to catalyze reduced bitterness.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.23 no.3
• /
• pp.43-55
• /
• 2021

Unlike nail care, nail art is a field with strong decorative elements that decorate the surface of the nail. In line with the trend of the times, which freely expresses one's personality, nail art is establishing itself as a definite and a key area in the beauty industry. Currently, design creation and technology developments are important, with the release of various nail materials and new trends that spread through mass media. Despite the great developments in the nail beauty industry, there is a lack for nail artists. Due to this fact, it is considered a necessary to combine nail art with the contemporary art styles, which have various motifs of design, and to study nail art design using them. In response, this study selected art from the Rococo era, where delicate and colorful decorative elements were at their peak, to consider the artistic styles of the time and present them in various nail designs. This study would like to expand the scope of new nail designs by suggesting colorful and feminine designs to women, who are the main customers of nail salon. In addition, the purpose of this study is to provide nail artists with basic materials that can be used in creative ideas and expressions, such as 2D and 3D nail designs, and composite nail design art, which are the art areas for nail art.

• Structural Engineering and Mechanics
• /
• v.70 no.6
• /
• pp.703-710
• /
• 2019

While fiber-reinforced plastic (FRP) materials have been largely used in the retrofitting of concrete buildings, its application has been limited because of some problems such as de-bonding of FRP layers from the concrete surface. This paper is the part of a wide experimental and analytical investigation about flexural retrofitting of reinforced concrete (RC) columns using FRP and mechanical fasteners (MF). A new generation of MF is proposed, which is applicable for retrofitting of RC columns. Furthermore, generally, to evaluate a retrofitted structure the nonlinear static and dynamic analyses are the most accurate methods to estimate the performance of a structure. In the nonlinear analysis of a structure, accurate modeling of structural elements is necessary for estimation the reasonable results. So for nonlinear analysis of a structure, modeling parameters for beams, columns, and beam-column joints are essential. According to the concentrated hinge method, which is one of the most popular nonlinear modeling methods, structural members shall be modeled using concentrated or distributed plastic hinge models using modeling parameters. The nonlinear models of members should be capable of representing the inelastic response of the component. On the other hand, in performance based design to make a decision about a structure or design a new one, numerical acceptance should be determined. Modeling parameters and numerical acceptance criteria are different for buildings of different types and for different performance levels. In this paper, a new method was proposed for FRP retrofitted columns to avoid FRP debonding. For this purpose, mechanical fasteners were used to achieve the composite behavior of FRP and concrete columns. The experimental results showed that the use of the new method proposed in this paper increased the flexural strength and lateral load capacity of the columns significantly, and a good composition of FRP and RC column was achieved. Moreover, the modeling parameters and acceptance criteria were presented, which were derived from the experimental study in order to use in nonlinear analysis and performance-based design approach.

• Composites Research
• /
• v.34 no.1
• /
• pp.47-50
• /
• 2021

In this paper, the Curing process for Epoxy Molding Compound (EMC) Package was developed by comparing the performance of the EMC/Cu Bi-layer package manufactured by the conventional Hot Press process system and Carbon Nanotubes (CNT) Heater process system of the surface heating system. The viscosity of EMC was measured by using a rheometer for the curing cycle of the CNT Heater. In the EMC/Cu Bi-layer Package manufactured through the two process methods by mentioned above, the voids inside the EMC was analyzed using an optical microscope. In addition, the interfacial void and warpage of the EMC/Cu Bi-layer Package were analyzed through C-Scanning Acoustic Microscope and 3D-Digital Image Correlation. According to these experimental results, it was confirmed that there was neither void in the EMC interior nor difference in the warpage at room temperature, the zero-warpage temperature and the change in warpage.

• Membrane Journal
• /
• v.31 no.3
• /
• pp.170-183
• /
• 2021

Fouling has continued to be a problem that hinders the effectiveness of membrane properties. To solve this problem of reducing fouling effects on membrane surface properties, different and innovative types of membrane patterning has been proposed. This article reviews on the progress of patterned membranes and their separation process concerning the fouling effects of membranes. The types of separation processes that utilize the maximum effectiveness of the patterned membranes include nanofiltration (NF), reverse osmosis (RO), microfiltration (MF), ultrafiltration (UF), and pervaporation (PV). Using these separation processes have shown and prove to have a major effect on reducing fouling effects, and in addition, they also add beneficial properties to the patterned membranes. Each patterned membrane and their separation processes gave notable results in threshold towards flux, salt rejections, hydrophilicity and much more, but there are also some unsolved cases to be pointed out. In this review, the effects of patterned membrane for separation processes will be discussed.

• Advances in nano research
• /
• v.10 no.3
• /
• pp.295-312
• /
• 2021

A new ionic liquid functionalized magnetic silica nanoparticle was synthesized and characterized and tested as an adsorbent. The adsorbent was used for magnetic solid phase extraction on ICP-MS method. Simultaneous determination of precious metal Au has been addressed. The method is simple and fast and has been applied to standard water and surface water analysis. A new method for separation/analysis of trace precious metal Au by Magnetron Solid Phase Extraction (MSPE) combined with ICP-MS. The element to be tested is rapidly adsorbed on CoFe2O4@SiO2@[BMIM]PF6 composite nano-adsorbent and eluted with thiourea. The method has a preconcentration factor of 9.5-fold. This method has been successfully applied to the determination of gold in actual water samples. Hydrophobic Ionic Liquids (ILs) 1-butyl-3-methylimidazole hexafluorophosphate ([BMIM]PF6) coated CoFe2O4@SiO2 nanoparticles with core-shell structure to prepare magnetic solid phase extraction agent (CoFe2O4@SiO2@ILs) and establish a new method of MSPE coupled with inductively coupled plasma mass spectrometry for separation/analysis of trace gold. The results showed that trace gold was adsorbed rapidly by CoFe2O4@SiO2@[BMIM]PF6 and eluanted by thiourea. Under the optimal conditions, preconcentration factor of the proposed method was 9.5-fold. The linear range, detection limit, correlation coefficient (R) and relative standard deviation (RSD) were found to be 0.01~1000.00 ng·mL-1, 0.001 ng·mL-1, 0.9990 and 3.4% (n = 11, c = 4.5 ng·mL-1). The CoFe2O4@SiO2 nanoparticles could be used repeatedly for 8 times. This proposed method has been successfully applied to the determination of trace gold in water samples.

• Composites Research
• /
• v.33 no.6
• /
• pp.336-340
• /
• 2020

In this study, carbon aerogels (CA) were prepared by sol-gel polycondensation of resorcinol and furfural in isopropanol using hexamethylenetetramine as a catalyst, and then directly drying the organic gels under isopropanol freeze-drying conditions, followed by carbonization under a nitrogen atmosphere. The preparation conditions of the CA were explored by changing the mole ratio of resorcinol to furfural. The effect of the preparation conditions on the pore structure of the CA was studied by nitrogen adsorption isotherms. The characteristics of the CA were studied by scanning and transition electron microscopy, and infrared spectrometry. The accessibility of pores and performance of the CA as an electrode in electric double layer capacitors were also electrochemically investigated. As a result, BET surface area and specific capacitance increased with the molar ratio of resorcinol to catalyst (R/C) ratio; the maximum values of 765 ㎡/g and 132 F/g were achieved at the R/C ratio of 200, respectively. Consequently, it was confirmed that increasing the R/C ratio increased the average pore size of the CA electrode, which improved the rate capability of the system.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.70-79
• /
• 2022

Biodiesel production has attracted attention as a sustainable source of fuel and is a competitive alternate to diesel engines. The glycerol that is produced as a by-product is generally discarded as waste and can be converted to green chemicals such as acetins to increase bio-diesel profitability. Acetins find application in fuel, food, pharmaceutical and leather industries. Batch experiments and analysis have been previously conducted for synthesis of acetins using glycerol esterification reaction aided by sulfated metal oxide catalysts (SO₄^2-/CeO₂-ZrO₂). The aim of this study was to optimize process parameters: effects of mole ratio of reactants (glycerol and acetic acid), catalyst concentration and reaction temperature to maximize glycerol conversion/acetin selectivity. The optimum conditions for this reaction were determined using response surface methodology (RSM) designed as per a five-level-three-factor central composite design (CCD). Statistica software 10 was used to analyze the experimental data obtained. The optimized conditions obtained were molar ratio - 1:12, catalyst concentration - 6 wt.% and temperature -90 ℃. A packed bed reactor was fabricated and column studies were performed using the optimized conditions. The breakthrough curve was analyzed.