본 논문에서는 "KSR-III 복합재 가압탱크“에 대한 구조 설계/제작 과정을 기술하였다. 복합재 가압탱크는 라이너 위에 복합재가 덮어 씌워진 형태이다. 하중을 부담하지 않는 라이너는 AI 6061-0로 만들어 졌으며, 라이너는 헬륨가스 기밀만을 담당하였다. 복합재 탱크는 라이너 위에 T700/Epoxy로 와인딩 하였다. 알루미늄 라이너가 얇았기 때문에 다단계 경화 공정이 필라멘트 와인딩 기법에 적용되었다. 다단계 경화 공정은 라이너의 실린더가 원형 형상을 잃지 않게 하였다. 보스부의 체결력은 보스링에 의하여 카본섬유로 분산되었다. 또한 보스링은 보스부의 국부적 변형을 막았다.
본 연구에서는 미국의 DOT-CFFC와 한국의 KS 기준에 근거하여 수소가스 복합소재 연료탱크에 대한 강도안전성을 FEM으로 해석하였다. 알루미늄 라이너 소재인 6061-T6와 탄소섬유 복합소재인 T800-24K로 적층이 형성되도록 감은 수소가스 복합소재 연료탱크는 130L의 저장용량을 갖으며, 70MPa의 충전압력으로 수소가스가 채워진다. FEM 해석결과에 의하면, 내부탱크를 형성하는 알루미늄 라이너에 작용하는 von Mises 응력 255.2MPa은 알루미늄 소재의 항복응력 대비 95%인 272MPa보다 낮기 때문에 안전하다. 또한, 복합소재 연료탱크에서 후프방향의 탄소섬유 응력비는 3.11이고, 헤리컬방향의 응력비는 3.04인 것으로 나타났다. 이들 응력비 데이터는 탄소섬유 복합소재 연료탱크에서 안전기준으로 권고한 2.4에 비해 높기 때문에 양방향 모두에서 안전하다. 따라서 70MPa의 충전압력을 갖는 130L 저장용량의 복합소재 연료탱크에 대한 강도안전성은 유용한 것으로 판단된다.
본 연구에서는 열탄성 해석과 복합재/알루미늄 링시편 실험을 통해 성형 온도와 자긴 압력이 복합재와 알루미늄 라이너로 구성된 Type 3 극저온 추진제 탱크에 미치는 영향을 살펴보았다. 우선 Type 3 탱크의 온도분포를 구한 뒤 이를 경계조건으로 사용하여 성형온도와 자긴 압력의 영향을 고려한 탄성해석을 수행하였다. 그 결과 복합재의 성형온도가 증가할수록 복합재와 알루미늄 라이너에 각각 잔류압축응력과 잔류인장응력이 증가하였다. 한편 자긴 압력은 극저온 환경에 의해 유발된 잔류열응력의 감소를 초래하였으며 자긴 압력의 크기가 증가할수록 이러한 경향은 두드러졌다. 이러한 성형 온도와 자긴 압력의 영향은 Type 3 극저온 추진제 탱크의 설계 및 제작 단계에 반드시 고려되어야 한다.
In this research, the design methods of the rocket joint parts were suggested. In the first section, nonlinear finite element analyses for joint parts of a composite pressure tank were performed. In the analyses, the detailed finite element modeling was performed and complex boundary conditions(contact problem, clamping force) were considered. Secondly, several guidelines for the design of joint parts were suggested. The parametric study for geometric design variables was peformed. Finally, the parametric study result was categorized for the multi-Joint part design of the axi-symmetric composite structure.
Filament wound pressure vessels have been studied for the efficient design tool to consider the variation of fiber angles through-the thickness direction. Filament winding patterns were simulated from semi-geodesic fiber path equation to calculate fiber path on arbitrary surface. Finite element analyses were performed considering fiber angle variation in longitudinal and thickness directions by ABAQUS. For the finite element modeling of the pressure tank, the 3-dimensional layered solid element was utilized. From the stress results of pressure tanks, maximum stress criterion in transverse direction was applied to modify material properties for failed region. In the end of each load increment, resultant layer stresses were compared with a failure criterion and properties were reduced to 1/10 for a failed layer. Results of progressive failure analysis were compared with two experimental data.
본 연구에서는 70MPa의 충전압력을 갖는 110L 수소연료 저장탱크에 대한 강도안전성을 FEM으로 해석하였다. 6061-T6 알루미늄 라이너의 외벽면에는 Toray의 T800-24K와 T700-12K, 그리고 Mitsubishi Ray의 MR60H-24P 탄소섬유를 사용하여 와인딩한 복합소재 연료탱크의 강도안전성을 미국의 DOT-CFFC와 KS의 안전규격으로 고찰하였다. 70MPa용 수소가스탱크의 응력강도에 대한 FEM 해석결과에 의하면, 거의 유사한 소재특성을 갖는 Toray의 T800-24K와 Mitsubishi Ray의 MR60H-24P는 70MPa의 수소연료 저장탱크를 제조하는데 사용해도 안전한 것으로 나타났다. 반면에, Toray의 T700-12K는 70MPa의 충전압력을 갖는 복합소재 저장탱크를 제조하기에는 강도안전성을 보장할 수 없으므로 60MPa 이하의 수소연료 복합소재탱크 제조를 권장한다.
In-situ structural health monitoring of filament wound pressure tanks were conducted during water-pressurizing test using embedded fiber Bragg grating (FBG) sensors. We need to monitor inner strains during working in order to verify the health condition of pressure tanks more accurately because finite element analyses on filament wound pressure tanks usually show large differences between inner and outer strains. Fiber optic sensors, especially FBG sensors can be easily embedded into the composite structures contrary to conventional electric strain gages (ESGs). In addition, many FBG sensors can be multiplexed in single optical fiber using wavelength division multiplexing (WDM) techniques. We fabricated a standard testing and evaluation bottle (STEB) with embedded FBG sensors and performed a water-pressurizing test. In order to increase the survivability of embedded FBG sensors, we suggested a revised fabrication process for embedding FBG sensors into a filament wound pressure tank, which includes a new protecting technique of sensor heads, the grating parts. From the experimental results, it was demonstrated that FBG sensors can be successfully adapted to filament wound pressure tanks for their structural health monitoring by embedding.
여러 복합재료 제작기법 중에서 필라멘트 와인딩 제작 기법은 압력탱크, 파이프 등과 같은 실린더 형태의 축대칭 구조물의 제작에 가장 효율적인 방법이다. 또한, 필라멘트 와인딩으로 제작된 복합재료 압력탱크는 운용 중 큰 내압을 받게 되며 복잡한 손상 메커니즘과 파손 모드를 가지고 있다. 그러므로, 필라멘트 와인딩으로 제작된 복합재료 압력탱크는 탱크의 제작 과정과 제작 후 전 과정 동안의 탱크에 대한 건전성 모니터링이 필요하며 이를 위해 탱크의 제작 시부터 탱크 내부의 여러 지점에 센서가 삽입 적용되어야 한다. 여러 센서 중에서 광섬유 센서는 복합재료 내부에 삽입이용이한 센서이며 특히, 광섬유 브래그 격자 센서(fiber Bragg grating Sensors, FBG센서)는 다중화(multiplexing)가 용이한 것을 큰 장점으로 가장 많이 채택되고 있다. 하지만, FBG 센서를 필라멘트 와인딩된 복합재료 압력탱크에 성공적으로 삽입 적용하기 위해서는 극심한 탱크의 삽입 환경에 대한 센서의 삽입 기법의 개발이 선행되어야 한다. 본 연구에서는 필라멘트 와인딩된 복합재료 압력탱크의 제작 시 FBG 센서를 탱크 내부에 다중화하여 삽입적용하기 위한 기법에 대하여 연구하였다.
This is a study on the distribution of acoustic emission parameters during a burst test for a type-II CNG vehicle fuel tank. A resonant AE sensor with a central frequency of 150 kHz was attached to the composite materials in the center of the fuel tank. The pressure was increased from 30 to 100% of the expected burst pressure and was maintained for 10 minutes at each level. Damage at 70% of expected burst pressure occurred by various damage mechanisms including fiber breakage and delamination, while that of below 60% only occurred by matrix crack initiation and growth. The count, duration and rise time of the AE signal at 60% of the expected burst pressure are distributed below 500, 5000 ${\mu}s$ and 300 ${\mu}s$, respectively. Then, at above 70% they increased with pressure by superimposing of individual AE signal generated at a nearby place. These results confirmed that the analysis of the distribution of AE parameters is an effective tool for estimating damage of a CNG fuel tank.
항공기 날개 구조물은 유체를 포함한 연료탱크로 사용되며, 연료탱크와 날개구조물을 연결하는 체결부는 복합재 구조물을 사용한다. 항공기 날개 구조물에 고속의 물체가 관통 또는 폭발하게 되면 수압램 현상이 발생하며, 수압램 현상에 의해 연료탱크에 높은 압력이 생성된다. 이러한 높은 앞력은 날개구조물 뿐만 아니라 연료탱크와 체결부의 파손을 야기하기 때문에 전투용 항공기의 기체 생존성 확보를 위해서는 수압램 효과에 대한 체결부의 거동을 확인해야 한다. 본 연구에서는 수압램 검증 시험에 앞서 항공기의 복합재 날개 외피와 스파 체결부를 모사한 4종류의 복합재 T-Joint에 정적 인장 시험을 수행하여 시편의 파손 거동을 스트레인 게이지와 초고속 카메라를 통해 확인하였다. 스트레인 게이지를 통해 얻은 변형률을 기준으로 동일한 형상과 하중 조건을 갖는 유한요소해석 모델링의 해석 결과를 비교하여 모델링의 타당성을 확인하였으며, 정적 하중에서 복합재 T-Joint의 파손응력을 확인하였다. 유한요소해석을 통해 향후 진행될 수압램 시험에서 각 시편이 파손되는 압력을 예측하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.