• Steel and Composite Structures
• /
• 제32권4호
• /
• pp.537-548
• /
• 2019

This paper introduces an improved numerical model which can consider the bond-slip effect in steel-concrete composite structures without taking double nodes to minimize the complexity in constructing a finite element model. On the basis of a linear partial interaction theory and the use of the bond link element, the slip behavior is defined and the equivalent modulus of elasticity and yield strength for steel is derived. A solution procedure to evaluate the slip behavior along the interface of the composite flexural members is also proposed. After constructing the transfer matrix relation at an element level, successive application of the constructed relation is conducted from the first element to the last element with the compatibility condition and equilibrium equations at each node. Finally, correlation studies between numerical results and experimental data are conducted with the objective of establishing the validity of the proposed numerical model.

• Composites Research
• /
• 제32권5호
• /
• pp.249-257
• /
• 2019

In this paper, the buckling behavior of triaxially braided circular arch with monosymmetric open section subjected to three-point bending was studied experimentally and numerically. First, test specimens were manufactured using vacuum assisted resin transfer molding (VARTM). Then the specimen was tested under three-point bending to determine the ultimate buckling strength. Before performing the numerical analysis, effective material properties of the braided composite were obtained through micro-meso scale analysis virtual testing validated with available test results. Then linear buckling analysis and geometrically non-linear post buckling analysis, established to simulate the test setup, were performed to study the buckling behavior of the composite frame. Analysis results were compared with experimentally obtained ones for verification. The effect of manufacturing defects of tow misalignment, irregular surface and resin rich region, and uncertainties during test setup were studied using numerical models. From the numerical analyses performed it was observed that both manufacturing defect and uncertainties had effect on the buckling behavior and strength.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2007년도 정기 학술대회 논문집
• /
• pp.688-693
• /
• 2007

Nowadays various studies related with superstructure of bridges are developed and they pursuit more effective section of bridges superstructure, material and economical application of composite materials. CFT structure(Concrete Filled Steel Tubular Structure) is developed type of composite structure that concrete is filled with steel box, and the deformation of the member, stiffness and internal force will be improved by confinement effect of steel box and concrete. This paper introduces new type of girder, CFTA girder( Concrete- Filled and Tied Steel Tubular Arch Girder) which is combined with traditional CFT structure,arch effect and prestress through carrying out the structural analysis by computer programs. The computer programs which is used are ABAQCS and MIDAS, and the 12.2m girder which is applied same load and prestresses is analyzed and compared the results respectively.

• Computers and Concrete
• /
• 제22권3호
• /
• pp.279-289
• /
• 2018

Shear walls are one of the important structural elements for bearing loads imposed on buildings due to winds and earthquakes. Composite shear walls with high lateral resistance, and high energy dissipation capacity are considered as a lateral load system in such buildings. In this paper, a composite shear wall consisting of steel faceplates, infill concrete and tie bars which tied steel faceplates together, and concrete filled steel tubular (CFST) as boundary columns, was modeled numerically. Test results were compared with the existing experimental results in order to validate the proposed numerical model. Then, the effects of some parameters on the behavior of the composite shear wall were studied; so, the diameter and spacing of tie bars, thickness and compressive strength of infill concrete, thickness of steel faceplates, and the effect of strengthening the bottom region of the wall were considered. The seismic behavior of the modeled composite shear wall was evaluated in terms of stiffness, ductility, lateral strength, and energy dissipation capacity. The results of the study showed that the diameter of tie bars had a trivial effect on the performance of the composite shear wall, but increasing the tie bars spacing decreased ductility. Studying the effect of infill concrete thickness, concrete compressive strength, and thickness of steel faceplates also showed that the main role of infill concrete was to prevent buckling of steel faceplates. Also, by strengthening the bottom region of the wall, as long as the strengthened part did not provide a support performance for the upper part, the behavior of the composite shear wall was improved; otherwise, ductility of the wall could be reduced severely.

• 복합신소재구조학회 논문집
• /
• 제2권2호
• /
• pp.7-12
• /
• 2011

현재 강재와 콘크리트를 합성화 시키는 방법으로 대표적인 것이 스터드를 이용하는 것이다. 그러나 이 방법을 강합성 기둥에 적용할 경우에 용접량이 많아져 이로 인하여 강재의 성능이 변하여 국부좌굴로 유도될 가능성이 매우 크다. 외부가 구속된 CFT 부재나 내부 구속 중공 CFT 부재 그리고 내부가 강관으로 내부 구속 중공 RC 부재에 적용할 경우에 합성 거더에 비하여 강재와 콘크리트가 분리되려는 인발력 대신 슬립에 의한 분리현상이 더 크게 발생한다. 이렇기 때문에 스터드의 높이 보다는 콘크리트와 강재가 합성되는 면적을 넓혀주는 것이 더 필요하다. 이러한 목적을 달성하기 위하여 일정부분 강관에 용접을 하여 부착을 하고 ㄷ자 형으로 제작된 슬립앵커의 철근이 콘크리트 속에 삽입되어 강재와 콘크리트의 일체 거동성을 높였다. 이러한 방법의 경우에는 곡률을 가진 강구조물 등에 적용될 경우 큰 효과를 발휘할 것으로 판단된다. 본 연구에서는 제안된 슬립앵커를 H빔에 설치를 하여 축하중을 가하는 Push-over Test를 통하여 거동 특성을 분석하였다.

• 비파괴검사학회지
• /
• 제27권4호
• /
• pp.328-338
• /
• 2007

스마트 재료를 이용한 복합재료의 가장 큰 장점 중의 하나는 재료내부에 발생한 균열을 제어하는데 있다. 구조용 재료로 사용 중에 구조물 내에 균열이 발생할 때 균열의 진전을 억제할 수 있는 방법 중의 하나가 형상기억합금재료의 형상기억효과를 이용하는 것이다. 본 연구에서는 최적의 제조조건을 도출하여 형상기억합금을 이용한 형상기억복합재료를 제조하였다. 또한 형상기억복합재료 내부의 형상기억합금에 의한 형상기억효과를 평가하기 위하여 복합재료에 인장하중을 가하여 복합재료에 발생하는 응력분포를 평가하고 복합재료에 열을 가하여 형상기억합금을 원래의 상태로 복귀하면서 복합재료 전체의 응력변화를 평가하였다. 형상기억복합재료의 인장하중에 따른 응력분포를 관찰하기 위하여 광탄성에 의한 가시화 장치를 이용하였다.

• Steel and Composite Structures
• /
• 제37권4호
• /
• pp.419-429
• /
• 2020

Composite structures are generally pressurized at both sides when repaired by the scarf repair method. But single-face vacuum bag curing (SVC) may be used in some practical scarf repair of penetration damage due to the low accessibility of composite structures, which can decrease bonding quality and may reduce structural mechanical properties. In this paper, experimental investigations were conducted on tensile and compressive properties of scarf-repaired composite laminates using SVC and double-face vacuum bag curing (DVC) in four hygrothermal environments. Finite element models of composite scarf joints with voids were established to further explore the failure mechanism of scarf-repaired laminates. Results show that the curing condition hardly affects tensile and compressive properties of the repaired laminates though it significantly affects the bonding quality with adhesive inner voids. Failure loads of scarf joints almost keep unchanged with adhesive voids increasing.

• Structural Engineering and Mechanics
• /
• 제55권3호
• /
• pp.511-523
• /
• 2015

Damaged steel-concrete composite girders can be repaired and retrofitted by epoxy-bonded carbon fiber-reinforced polymer (CFRP) sheets to the critical areas of tension flanges. This paper presents the results of a study on the behavior of damaged steel-concrete composite girders repaired with CFRP sheets under static loading. A total of seven composite girders made of I20A steel sections and 80mm-thick by 900mm-wide concrete slabs were prepared and tested. CFRP sheets and prestressed CFRP sheets were used to repair the specimens. The specimens lost the cross-sectional area of their tension flanges with 30%, 50% and 100%. The results showed that CFRP sheets had no significant effect on the yield loads of strengthened composite girders, but had significant effect on the ultimate loads. The yield loads, elastic stiffness, and ultimate bearing capacities of strengthened composite girders had been changed as a result of prestressed CFRP sheets, the utilization ratio of CFRP sheets could be effectively improved by applying prestress to CFRP sheets. Both the yield loads and ultimate bearing capacities had been changed as a result of steel beam's flange damage level and CFRP sheets could cover the girders' shortage of bearing capacity with 30% and 50% flange damage, respectively.

• 한국세라믹학회지
• /
• 제30권4호
• /
• pp.316-324
• /
• 1993

Three types of dispersed, coated and mechanically mixed SiC reinforced Al2O3 composite powders were used to investigate the effect of composite powder type on sintering characteristics and properties of Al2O3-SiC composites. Sinterability of coated type composite powders was superior to that of other composite powders when they were pressureless sintered at 1500~1$700^{\circ}C$ for 2h in Ar atmosphere. However, sinterabilities (>98% TD) of each type of composite powders were similar when they were hot pressed at 180$0^{\circ}C$ for 1h under 30MPa in N2 atmosphere. SiC powders were randomly distributed in the specimen prepared from dispersed type composite powders, whereas homogeneously distributed for coated type specimens. It was found that SiC powders inhibited the grain growth of Al2O3, and fracture toughness was increased by the increment of crack growth resistance due to residual stress by secondary SiC particles within Al2O3 grains.

• 복합신소재구조학회 논문집
• /
• 제4권4호
• /
• pp.15-21
• /
• 2013

This study carried out finite element deflection analysis of cylindrical shell structures made of composite materials, which is based on the micro-mechanical approach for different fiber-volume fractions. The finite element (FE) models for composite structures using multi-scale approaches described in this paper is attractive not only because it shows excellent accuracy in analysis but also it shows the effect of the material combination. New results reported in this paper are focused on the significant effects of the fiber-volume fraction for various parameters, such as fiber angles, layup sequences, and length-thickness ratios. It may be concluded from this study that the combination effect of fiber and matrix, largely governing the dynamic characteristics of composite shell structures, should not be neglected and thus the optimal combination could be used to design such civil structures for better dynamic performance.