• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.58-67
• /
• 2003

An automotive engine cooling system is closely related with overall engine performances, such as reduction of fuel consumption, decrease of air pollution, and increase of engine life. Because of complex reaction between each component, the direct experiment, using a vehicle, takes high cost, long time, and slow response to the system change. Therefore, a computer simulation would provide the designer with an inexpensive and effective tool for design, development, and optimization of the engine cooling system over a wide range of operating conditions. In this work, it has been predicted the thermal performance of the engine cooling system in cases of stationary mode, constant speed mode, and city-drive mode by mathematical modelling of each component and numerical analysis. The components are engine, radiator, heater, thermostat, water pump, and cooling fans. Since the engine model is the most important, that is divided into eight sub-sections. The volume mean temperature of eight sub-sections are simultaneously calculated at a time. For detail calculation, the radiator and heater are also divided into many sub-sections like control volumes in finite difference method. Each sub-section is assumed to consist of three parts, coolant, tube with fin, and air. Hence it has been developed the simulation program that can be used in case of design and system configuration changes. The overall performance results obtained by the program were desirable and the time-traced tendencies of the results agreed fairly well with those of actual situations.

• 한국재료학회지
• /
• 제18권2호
• /
• pp.107-111
• /
• 2008

[ $BaO{\cdot}Nd_2O_3{\cdot}5TiO_2$ ] (BNT) ceramics modified with a borate glass containing Ba, Nd and Ti as glass constituents were investigated with regard to their sintering behavior and microwave dielectric properties. An addition of iso-component glass significantly improved the sinterabilty of the BNT ceramics and lowered the sintering temperature. A maximum density of $5.29\;g/cm^3$ and an x-y shrinkage of 17% were obtained for BNT ceramics containing 10wt.% of the glass sintered at $1100^{\circ}C$. The dielectric composition without the glass additive was only slightly densified at $1100^{\circ}C$. The resulting sample exhibited two crystalline phases, $BaNd_2Ti_5O_{14}$ and $Ba_2Ti_9O_{20}$, regardless of sintering temperature and glass content. When >10wt.% glass was added, exaggerated grain growth with a less uniform microstructure was found, resulting in the subsequent reduction of the fired density and the dielectric properties. BNT ceramics containing 10wt.% of the isocomponent glass sintered at $1100^{\circ}C$ for 4 h showed promising dielectric properties of k = 71.3 and Q = 1,330.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 춘계학술대회
• /
• pp.703-708
• /
• 2009

본 논문에서는 ZnO와 $Ga_2O_3$ 분말을 1:1의 mole비로 혼합하고 여기에 Mn을 첨가하여 Ar이나 진공 분위기에서 $ZnGa_2O_4$ : Mn을 합성하였다. 제작된 $ZnGa_2O_4$ : Mn의 발광 스펙트럼, 표면 사진 및 성분비를 측정하여 산소의 성분 변화가 발광 특성에 미치는 영향을 규명하고자 하였다. 또한 저온의 Photoluminescence(PL) 스펙트럼으로부터 Mn의 site symmetry가 발광 스펙트럼에 미치는 영향을 설명하였다.

• 한국재료학회지
• /
• 제34권5호
• /
• pp.242-246
• /
• 2024

La modified lead zirconate titanate ceramics (Pb_0.92La_0.08)(Zr_0.95Ti_0.05)O₃ = PLZT-8/95/5 were prepared using the conventional solid state reaction method in order to investigate the complex impedance characteristics of the PLZT-8/95/5 ceramic according to temperature. The complex impedance in the PLZT-8/95/5 ceramic was measured over a temperature range of 30~550 ℃ at several frequencies. The complex dielectric constant anomaly of the phase transition was observed near T_U1 = 179 ℃ and T_U2 = 230 ℃. A remarkable diffuse dielectric constant anomalous behaviour of the complex dielectric constant was found between 100 ℃ and 550 ℃. The complex impedance spectra below and above T_U1 and T_U2 were fitted by the superposition of two Cole-Cole types of impedance relaxations. The fast component in the higher frequency region may be due to ion migration in the bulk, and the slow component in the lower frequency region is interpreted to be the formation and migration of ions at the grain boundary or electrode/crystal interfacial polarization.

• Journal of Acupuncture Research
• /
• 제15권2호
• /
• pp.1-15
• /
• 1998

Purpose : The study for changes in components and acitvities of Artemisiae Herba at various processing temperature is generally regarded as a foundation in setting the optimum heat-processing temperature and for getting the maximum activities for medical usage of this herb. Methods: Therefore some experiments were performed either in vitro or in vivo and various changes were observed - the changes in the weitht of Artemisiae Herba, the changes in the relative amount of three kinds of extracts from Artemisiae Herba ( diluted ethanol extract, water extract, ether extract ), the TLC pattern of essential oil at various processing temperature, the existance of inhibitory effects both on ${\beta}$-Glucuronidase activities, and on heat-induced hemolysis, the effects on increased vascular permeability. The valid results derived from the experiments are as follows. Results: 1. The weight of Artemisiae Herba prominently decreased at 240^{\circ}C$. 2. The contents of diluted ether extract were maximum in the unprocessing condition. Those of water extract were maximum at 180^{\circ}C$ and at 210^{\circ}C$. and the changes of diluted ethanol extract at 150^{\circ}C$. 3. The TLC pattern of essential oil in Artemisiae Herba at various processing temperature showed that a component began to increase at Rf 0.56 and another component began to decrease at Rf 0.86. 4. The contents of Eupatilin in Artemisiae Herba at various processing temperature continued to decreased in proportion to the temperature rise, the extent of which was prominent at 210^{\circ}C$, and was unnoticeable at 270^{\circ}C$. 5. Inhibitory effects on ${\beta}$-Glucuronidase activities, trypsin activities and heat-induced hemolysis increased in proportion to the density of Artemisiae Herba. Inhibitory effects on ${\beta}$-Glucuronidase activities and trypsin activities were relatively high at 180^{\circ}C$ while on the writhing syndrome and inhibitory effects on increased vascular permeability induced by acetic acid were maximum at 240^{\circ}C$. those on heat-induced hemolysis were relatively high at 240^{\circ}C$. 6. In vivo, both analgesic effects Conclusions: To maximize of the effectiveness of Artemmisiae Herba, the ideal heating temperature is in the range of 180^{\circ}C{\sim}240^{\circ}C$.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.610-616
• /
• 2011

The effect of curing temperature on basic geopolymeric reactivity and hardening behaviour of blast furnace slag were investigated using the mixture of pulverized slag and several alkaline solutions of relatively high concentration. For the pastes prepared at several different temperatures between 20$^{\circ}C$ and 90$^{\circ}C$, setting time and heat of reaction were examined while mineralogical and morphological examinations were performed for the hardened paste after curing period at same temperature. The geopolymeric reaction of slag was revealed to be accelerated strongly according to the curing temperature regardless of the sort and concentration of the alkaline solution. The increase of concentration of the alkaline solution within 9M and the existence of silicic ion in the solution also promoted the reaction severely. The mineral component and their ratio of the hardened paste were revealed to be influenced by the chemical species and silicic ion contained in alkaline solution rather than by the curing temperature. The higher temperature and longer period of curing stage were effective for the sustained formation of geopolymer and succeed improvement of density and uniformity of morphology of the final hardened body.

• Tribology and Lubricants
• /
• 제21권4호
• /
• pp.171-176
• /
• 2005

O-ring seal is an essential component in various mechanical apparatuses for a sealing of oil container and pressure vessels. This paper presents the sealing pressure and compressive contact behaviors of hi-polymer O-rings, which is made by an outer shell of FFKM material and an inner solid ring of FKM one. The contact normal pressure and its ratios are measured by experimental method with an automatic control system of the working temperature and analyzed numerically by using the non-linear Marc FEM program. The results show reasonably good agreements between the computed FEM results and measured ones when the operating temperature is kom normal temperature of $18^{\circ}C$ and a high temperature of $300^{\circ}C$ But the compared values between the computed and tested results show a little difference because of the increased temperature, which is related to the non-linear parameter of the O-ring material. Bi-polymer 0-ring shows a good contact normal stress and compression behavior for a given operation temperature and compression ratio.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.281-284
• /
• 2006

PW206C 터보 축 엔진을 위해 신경회로망을 이용한 지능형 성능 진단 프로그램이 제안되었다. 이 엔진은 항공우주연구원에서 개발 중에 있는 틸트 로터 타입 스마트 무인기의 추진시스템으로 선정되었다. 스마트 무인기 추진시스템에서 계측되는 성능변수는 가스발생기 회전속도, 동력터빈 회전속도, 배기가스 온도, 토크 등 4개이다. 그러나 이러한 4개 계측변수로는 각 구성품의 손상 진단이 어려운 관계로 압축기 출구 압력 및 압축기 터빈 출구 온도를 포함한 6개의 계측변수를 진단에 이용하였다. 구성품 성능저하량을 판단하는 성능파라미터는 압축기, 압축기 터빈, 동력 터빈의 유량함수 및 효율이다. 신경망을 훈련하고 테스트하기 위한 데이터베이스는 가스터빈 성능모사 프로그램을 이용하여 구성하였다. 훈련된 신경망을 PW206C 터보 축 엔진의 진단에 적용한 결과 제안된 진단 알고리즘이 압축기 오염과 압축기 터빈의 침식과 같은 단일 손상을 탐지하는데 유용함을 확인하였다.

• 한국건설순환자원학회논문집
• /
• 제5권4호
• /
• pp.403-413
• /
• 2017

본 논문에서는 탄소저감을 위한 산업부산물 사용 증대 및 시공성능 향상을 위하여 시멘트 사용량을 80% 이상 감소시킨 탄소저감형 4성분계 고유동 콘크리트(QC-HFC)를 제조하여 품질특성 및 수화특성 평가를 수행하였다. QC-HFC의 품질은 목표 성능을 만족하는 결과를 얻을 수 있었으며, 유동 및 역학특성의 경우 기존에 적용되는 콘크리트와 유사한 수준인 것으로 나타났다. QC-HFC의 건조수축은 기존 배합과 비교하여 약 2배 이상, 수화열의 경우 약 36% 감소하는 것으로 결과가 나타났으며, 그 결과 수화열 저감 효과에 따른 온도응력 감소, 상대적으로 작은 내외부 온도차로 인한 변형 감소로 균열 발생량을 저감시킬 수 있을 것으로 판단된다. 또한 매스 구조물의 시뮬레이션을 실시한 결과 온도균열지수 1.1 이상으로 균열발생 확률이 약 35% 감소하는 결과가 나타남에 따라 온도에 의한 균열을 저감시킬 수 있을 것으로 판단된다.

• 한국전기전자재료학회논문지
• /
• 제33권5호
• /
• pp.373-379
• /
• 2020

In this study, TiN-coated cBN (cubic-structure boron nitride) powders were successfully synthesized by a sol-gel method using titanium (IV) isopropoxide (TTIP) and by controlling the heat treatment conditions. After the sol-gel process, amorphous nano-sized TiO_x was uniformly coated on the surface of cBN powder particles. The obtained TiO_x-coated cBN powders were heated at 1,000~1,300℃ for 1 or 6 h in a flow of 95%N₂-5%H₂ mixed gas. With increasing temperature, the chemical composition of the TiO_x coating layer changed in the order of TiO₂→Ti₆O₁₁→Ti₄O₇→TiN due to reduction of the Ti ions. The TiN coating layer was observable in the samples heated at 1,200℃ and appeared as the main phase in the sample heated at 1,300℃. The resulting thickness of the TiN coating layer of the sample heated at 1,300℃ was approximately 45~50 nm.